2002 JEEP LIBERTY Relay wiring diagram

(1) Disconnect and isolate the battery negative
cable.
(2) Unplug the blower motor relay from the PDC
located under the hood.
(3) Remove the blower motor relay.
INSTALLATION
(1) Install the blower motor relay by aligning the
relay terminals with the cavities in the PDC and
pushing the relay firmly into place.
(2) Connect the battery negative cable.
(3) Test the relay operation.
BLOWER MOTOR RESISTOR
DESCRIPTION
The blower motor resistor is mounted to the rear
side of the HVAC housing on the passenger side of
the vehicle.
OPERATION
The resistor is a credit card resistor that utilizes
resistor circuit tracers to reduce current flow to the
blower. The blower motor switch directs the ground
path through the correct resistor circuit to obtain the
selected speed.
The blower motor resistor cannot be repaired and,
if faulty or damaged, it must be replaced.
DIAGNOSIS AND TESTING - BLOWER MOTOR
RESISTOR
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Disconnect and isolate the battery negative
cable.(2) Open the glove box door and reach in and
unplug the wire harness connector from the blower
motor resistor.
(3) Check for continuity between each of the
blower motor switch input terminals of the resistor
and the resistor output terminal. In each case there
should be continuity. If OK, repair the wire harness
circuits between the blower motor switch and the
blower motor resistor or blower motor relay as
required. If not OK, replace the faulty blower motor
resistor.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Open the glove box door to gain access to the
blower motor resistor.
(3) Pull out the lock on the blower motor resistor
wire harness connector to unlock the connector latch.
(4) Depress the latch on the blower motor resistor
wire harness connector and unplug the connector
from the resistor.
(5) Remove the two screws that secure the resistor
to the HVAC housing.
(6) Remove the resistor from the HVAC housing.
INSTALLATION
(1) Install the new resistor in the HVAC housing.
(2) Install the two screws that secure the resistor
to the HVAC housing and tighten to 2.2 N´m (20 in.
lbs.).
(3) Plug in the blower motor harness connector.
(4) Push in the lock on the blower motor resistor
harness connector.
(5) Close the glove box door.
(6) Connect the battery negative cable.
24 - 22 CONTROLSKJ
BLOWER MOTOR RELAY (Continued)

BLOWER MOTOR
DESCRIPTION
The blower motor and blower wheel are located in
the passenger side end of the HVAC housing, below
the glove box. The blower motor controls the velocity
of air flowing through the HVAC housing by spinning
a squirrel cage-type blower wheel within the housing
at the selected speed. The blower motor and wheel
can be removed from the housing inside the vehicle
without removing the dash or HVAC housing assem-
bly.
OPERATION
The blower motor will only operate when the igni-
tion switch is in the On position, and the A/C Heater
mode control switch knob is in any position, except
Off. The blower motor receives a fused battery feed
through the blower motor relay whenever the igni-
tion switch is in the On position. The blower motor
battery feed circuit is protected by a fuse in the
Power Distribution Center (PDC). Blower motor
speed is controlled by regulating the ground path
through the A/C Heater control blower motor switch
and the blower motor resistor.
The blower motor and blower motor wheel cannot
be repaired and, if faulty or damaged, they must be
replaced. The blower motor and blower wheel are ser-
viced only as a unit.
DIAGNOSIS AND TESTING - BLOWER MOTOR
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). Possible causes of
an inoperative blower motor include:²Faulty fuse
²Faulty blower motor circuit wiring or wire har-
ness connectors
²Faulty blower motor resistor
²Faulty blower motor relay
²Faulty blower motor switch
²Faulty A/C Heater mode control switch
²Faulty blower motor.
Possible causes of the blower motor not operating
in all speeds include:
²Faulty blower motor switch
²Faulty blower motor resistor
²Faulty blower motor circuit wiring or wire har-
ness connectors.
VIBRATION
Possible causes of blower motor vibration include:
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower wheel out of balance or bent
²Blower motor faulty.
NOISE
To verify that the blower is the source of the noise,
unplug the blower motor wire harness connector and
operate the HVAC system. If the noise goes away,
possible causes include:
²Foreign material in the HVAC housing
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower motor faulty.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
24 - 30 DISTRIBUTIONKJ

COVER - REMOVAL, COWL TRIM.......23-157
COVER - REMOVAL, INSTRUMENT
PANEL TOP........................23-152
COVER - REMOVAL, STRUCTURAL........9-55
COVER(S) - DESCRIPTION, CYLINDER
HEAD...............................9-25
COVER(S) - INSTALLATION, CYLINDER
HEAD...........................9-26,9-34
COVER(S) - INSTALLATION, TIMING
BELT / CHAIN........................9-76
COVER(S) - REMOVAL, CYLINDER HEAD . . 9-25,
9-34
COVER(S) - REMOVAL, TIMING BELT /
CHAIN..............................9-74
COWL GRILLE - INSTALLATION........23-140
COWL GRILLE - REMOVAL............23-140
COWL TRIM COVER - INSTALLATION....23-157
COWL TRIM COVER - REMOVAL.......23-157
COWL WEATHERSTRIP - INSTALLATION . 23-185
COWL WEATHERSTRIP - REMOVAL.....23-185
COWL/PLENUM SEAL - INSTALLATION . . . 23-187
COWL/PLENUM SEAL - REMOVAL......23-187
COWL/PLENUM WINDOW BAFFLE SEAL -
INSTALLATION......................23-187
COWL/PLENUM WINDOW BAFFLE SEAL -
REMOVAL.........................23-187
CRADLE CROSSMEMBER -
INSTALLATION, ENGINE................13-6
CRADLE CROSSMEMBER - REMOVAL,
ENGINE.............................13-6
CRANKSHAFT - DESCRIPTION...........9-42
CRANKSHAFT - INSPECTION.............9-43
CRANKSHAFT - INSTALLATION...........9-43
CRANKSHAFT - REMOVAL..............9-43
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-47
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-46
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-48
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-48
CRANKSHAFT POSITION SENSOR -
DESCRIPTION.......................14-30
CRANKSHAFT POSITION SENSOR -
INSTALLATION.......................14-32
CRANKSHAFT POSITION SENSOR -
OPERATION.........................14-31
CRANKSHAFT POSITION SENSOR -
REMOVAL..........................14-31
CROSSMEMBER - INSTALLATION,
ENGINE CRADLE......................13-6
CROSSMEMBER - INSTALLATION,
RADIATOR.........................23-146
CROSSMEMBER - INSTALLATION, REAR . . . 13-7
CROSSMEMBER - REMOVAL, ENGINE
CRADLE.............................13-6
CROSSMEMBER - REMOVAL, RADIATOR . 23-146
CROSSMEMBER - REMOVAL, REAR.......13-7
CROSS-OVER PIPE - INSTALLATION.......11-3
CROSS-OVER PIPE - REMOVAL..........11-3
CRUISE INDICATOR - DESCRIPTION......8J-16
CRUISE INDICATOR - OPERATION.......8J-17
CURTAIN AIRBAG - DESCRIPTION, SIDE . . 8O-38
CURTAIN AIRBAG - INSTALLATION, SIDE . . 8O-41
CURTAIN AIRBAG - OPERATION, SIDE....8O-39
CURTAIN AIRBAG - REMOVAL, SIDE.....8O-40
CUSHION - FRONT - INSTALLATION,
SEAT .............................23-167
CUSHION - FRONT - INSTALLATION,
SEAT BACK........................23-167
CUSHION - FRONT - REMOVAL, SEAT . . . 23-167
CUSHION - FRONT - REMOVAL, SEAT
BACK.............................23-167
CUSHION - REAR - INSTALLATION, SEAT . 23-171
CUSHION - REAR - INSTALLATION, SEAT
BACK.............................23-170
CUSHION - REAR - REMOVAL, SEAT....23-171
CUSHION - REAR - REMOVAL, SEAT
BACK
.............................23-170
CUSHION COVER - FRONT -
INSTALLATION, SEAT
.................23-167
CUSHION COVER - FRONT - REMOVAL,
SEAT
.............................23-167
CUSHION SIDE SHIELDS -
INSTALLATION, SEAT
.................23-167
CUSHION SIDE SHIELDS - REMOVAL,
SEAT
.............................23-167CUSTOMER PREFERENCES - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-8
CV JOINT/BOOT-INNER - INSTALLATION . . . 3-17
CV JOINT/BOOT-INNER - REMOVAL.......3-15
CV JOINT/BOOT-OUTER - INSTALLATION . . . 3-13
CV JOINT/BOOT-OUTER - REMOVAL.......3-12
CYLINDER - DESCRIPTION, MASTER......5-24
CYLINDER - INSPECTION, MASTER........6-9
CYLINDER - INSTALLATION, FLIP-UP
GLASS SUPPORT...................23-139
CYLINDER - INSTALLATION, LOCK......23-125,
23-138
CYLINDER - INSTALLATION, LOCK.......19-11
CYLINDER - INSTALLATION, MASTER.....5-25
CYLINDER - INSTALLATION, SUPPORT . . . 23-120
CYLINDER - OPERATION, MASTER........5-24
CYLINDER - REMOVAL, FLIP-UP GLASS
SUPPORT.........................23-139
CYLINDER - REMOVAL, LOCK....23-125,23-137
CYLINDER - REMOVAL, LOCK...........19-10
CYLINDER - REMOVAL, MASTER.........5-25
CYLINDER - REMOVAL, SUPPORT......23-120
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER.................5-24
CYLINDER BORE HONING - STANDARD
PROCEDURE.........................9-39
CYLINDER COMBUSTION PRESSURE
LEAKAGE - DIAGNOSIS AND TESTING......9-8
CYLINDER COMPRESSION PRESSURE -
DIAGNOSIS AND TESTING...............9-8
CYLINDER FLUID LEVEL - STANDARD
PROCEDURES, MASTER................5-26
CYLINDER HEAD - DESCRIPTION.........9-30
CYLINDER HEAD COVER(S) -
DESCRIPTION........................9-25
CYLINDER HEAD COVER(S) -
INSTALLATION....................9-26,9-34
CYLINDER HEAD COVER(S) - REMOVAL . . . 9-25,
9-34
CYLINDER HEAD GASKET - DIAGNOSIS
AND TESTING....................9-19,9-30
CYLINDER LOCK SWITCH -
DESCRIPTION, DOOR..................8Q-9
CYLINDER LOCK SWITCH -
DESCRIPTION, TAILGATE...............8N-9
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR.................8Q-10
CYLINDER LOCK SWITCH - DIAGNOSIS
AND TESTING, TAILGATE...............8N-9
CYLINDER LOCK SWITCH -
INSTALLATION, DOOR.................8Q-10
CYLINDER LOCK SWITCH -
INSTALLATION, TAILGATE..............8N-10
CYLINDER LOCK SWITCH - OPERATION,
DOOR.............................8Q-10
CYLINDER LOCK SWITCH - OPERATION,
TAILGATE...........................8N-9
CYLINDER LOCK SWITCH - REMOVAL,
DOOR.............................8Q-10
CYLINDER LOCK SWITCH - REMOVAL,
TAILGATE..........................8N-10
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER . . 5-21,5-24
CYLINDERS - ASSEMBLY, WHEEL.........5-29
CYLINDERS - CLEANING, WHEEL.........5-28
CYLINDERS - DISASSEMBLY, WHEEL......5-28
CYLINDERS - INSPECTION, WHEEL.......5-29
CYLINDERS - INSTALLATION, WHEEL
.....5-29
CYLINDERS - REMOVAL, WHEEL
.........5-28
DAMAGED OR WORN THREADS -
STANDARD PROCEDURE, REPAIR
.........9-9
DAMPER - INSTALLATION, VIBRATION
.....9-55
DAMPER - REMOVAL, VIBRATION
........9-54
DATA LINK CONNECTOR - DESCRIPTION
. . 8E-10
DATA LINK CONNECTOR - OPERATION
....8E-10
DAYTIME RUNNING LAMP RELAY -
DESCRIPTION
.......................8L-20
DAYTIME RUNNING LAMP RELAY -
INSTALLATION
.......................8L-21
DAYTIME RUNNING LAMP RELAY -
OPERATION
.........................8L-20
DAYTIME RUNNING LAMP RELAY -
REMOVAL
..........................8L-21
DECOUPLER - DIAGNOSIS AND
TESTING, GENERATOR
................8F-27
DECOUPLER PULLEY - DESCRIPTION,
GENERATOR
........................8F-26DECOUPLER PULLEY - INSTALLATION,
GENERATOR........................8F-30
DECOUPLER PULLEY - OPERATION,
GENERATOR........................8F-27
DECOUPLER PULLEY - REMOVAL,
GENERATOR........................8F-27
DEFINITION - DESCRIPTION, TRIP.......25-19
DEFLECTOR - INSTALLATION, WIND.....23-180
DEFLECTOR - REMOVAL, WIND........23-180
DEFOGGER - DESCRIPTION, REAR
WINDOW............................8G-3
DEFOGGER - OPERATION, REAR
WINDOW............................8G-3
DEFOGGER FUNCTION - DIAGNOSIS AND
TESTING, REAR HVAC CONTROL
ASSEMBLY WINDOW..................8G-9
DEFOGGER GRID - DESCRIPTION, REAR
WINDOW............................8G-5
DEFOGGER GRID - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-5
DEFOGGER GRID - OPERATION, REAR
WINDOW............................8G-5
DEFOGGER RELAY - DESCRIPTION,
REAR WINDOW.......................8G-6
DEFOGGER RELAY - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-6
DEFOGGER RELAY - INSTALLATION,
REAR WINDOW.......................8G-7
DEFOGGER RELAY - OPERATION, REAR
WINDOW............................8G-6
DEFOGGER RELAY - REMOVAL, REAR
WINDOW............................8G-7
DEFOGGER SWITCH - DESCRIPTION,
REAR WINDOW.......................8G-8
DEFOGGER SWITCH - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-8
DEFOGGER SWITCH - OPERATION, REAR
WINDOW............................8G-8
DEFOGGER SYSTEM - DIAGNOSIS AND
TESTING, REAR WINDOW..............8G-4
DEFROST DOO - INSTALLATION, FLOOR . . 24-37
DEFROST DOOR - REMOVAL...........24-35
DEFROST DOOR - REMOVAL, FLOOR.....24-36
DEFROST DOOR ACTUATOR -
INSTALLATION, FLOOR................24-25
DEFROST DOOR ACTUATOR - REMOVAL,
FLOOR.............................24-24
DEFROST DUCT/DEMISTER ADAPTOR -
REMOVAL..........................24-32
DEFROST/DEMISTER DUCT -
INSTALLATION.......................24-32
DELIVERY - DESCRIPTION, FUEL.........14-2
DELIVERY - OPERATION, FUEL...........14-3
DEMAGNETIZING - STANDARD
PROCEDURE, COMPASS...............8M-2
DEMISTER OUTLETS - DESCRIPTION.....24-29
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL RESTRAINT............8O-6
DETECTION PUMP - DESCRIPTION, LEAK . 25-27
DETECTION PUMP - INSTALLATION,
LEAK..............................25-28
DETECTION PUMP - OPERATION, LEAK . . . 25-28
DETECTION PUMP - REMOVAL, LEAK....25-28
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE........................8W-01-8
DIAGNOSIS CHART - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-6
DIAGNOSIS, DIAGNOSIS AND TESTING -
WATER DRAINAGE AND WIND NOISE . . . 23-176
DIAGNOSTIC PROCEDURES, DIAGNOSIS
AND TESTING......................23-176
DIAGNOSTIC TROUBLE CODES -
DESCRIPTION........................25-2
DIAGNOSTICS (OBD) - DIAGNOSIS AND
TESTING, ON-BOARD...................7-3
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING......................8W-01-1
DIAGRAMS - HYDRAULIC SCHEMATICS,
SCHEMATICS.......................21-100
DIESEL - TORQUE, EXCEPT.............8F-23
DIFFERENTIAL - ASSEMBLY
........3-105,3-41
DIFFERENTIAL - DISASSEMBLY
.....3-105,3-41
DIFFERENTIAL - INSTALLATION
. 3-105,3-42,3-73
DIFFERENTIAL - REMOVAL
.....3-104,3-40,3-71
DIFFERENTIAL - TRAC-LOK - ASSEMBLY
. . 3-109,
3-77
KJINDEX 7
Description Group-Page Description Group-Page Description Group-Page

HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...............9-19,9-30
HEADLAMP BULB - INSTALLATION.......8L-32
HEADLAMP BULB - REMOVAL..........8L-31
HEADLAMP HIGH BEAM RELAY -
DESCRIPTION.......................8L-33
HEADLAMP HIGH BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-34
HEADLAMP HIGH BEAM RELAY -
INSTALLATION.......................8L-35
HEADLAMP HIGH BEAM RELAY -
OPERATION.........................8L-33
HEADLAMP HIGH BEAM RELAY -
REMOVAL..........................8L-34
HEADLAMP LEVELING MOTOR -
DESCRIPTION.......................8L-35
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-36
HEADLAMP LEVELING MOTOR -
OPERATION.........................8L-36
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-36
HEADLAMP LEVELING SWITCH -
DESCRIPTION.......................8L-37
HEADLAMP LEVELING SWITCH -
DIAGNOSIS AND TESTING.............8L-37
HEADLAMP LEVELING SWITCH -
INSTALLATION.......................8L-38
HEADLAMP LEVELING SWITCH -
OPERATION.........................8L-37
HEADLAMP LEVELING SWITCH -
REMOVAL..........................8L-38
HEADLAMP LOW BEAM RELAY -
DESCRIPTION.......................8L-39
HEADLAMP LOW BEAM RELAY -
DIAGNOSIS AND TESTING.............8L-40
HEADLAMP LOW BEAM RELAY -
INSTALLATION.......................8L-41
HEADLAMP LOW BEAM RELAY -
OPERATION.........................8L-39
HEADLAMP LOW BEAM RELAY -
REMOVAL..........................8L-40
HEADLAMP UNIT - ADJUSTMENT........8L-42
HEADLAMP UNIT - INSTALLATION.......8L-42
HEADLAMP UNIT - REMOVAL...........8L-41
HEADLINER - INSTALLATION..........23-159
HEADLINER - REMOVAL..............23-159
HEADREST - INSTALLATION...........23-164
HEADREST - REMOVAL...............23-164
HEADREST SLEEVE - INSTALLATION....23-164
HEADREST SLEEVE - REMOVAL........23-164
HEAT SHIELDS - DESCRIPTION..........11-4
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRRORS - DESCRIPTION.......8G-1
HEATED MIRRORS - DIAGNOSIS AND
TESTING............................8G-1
HEATED MIRRORS - OPERATION.........8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . 8G-13
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING.......................8G-13
HEATED SEAT ELEMENT - OPERATION....8G-13
HEATED SEAT MODULE - DESCRIPTION . . . 8E-21
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING.......................8E-22
HEATED SEAT MODULE - INSTALLATION . . 8E-24
HEATED SEAT MODULE - OPERATION....8E-21
HEATED SEAT MODULE - REMOVAL......8E-24
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING.......................8G-14
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING
..................8G-12,8G-14
HEATED SEAT SYSTEM - DESCRIPTION
. . . 8G-10
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING
.......................8G-11
HEATED SEAT SYSTEM - OPERATION
....8G-10
HEATER AND AIR CONDITIONER -
DESCRIPTION
........................24-1
HEATER AND AIR CONDITIONER -
OPERATION
..........................24-2
HEATER CONTROL - DESCRIPTION, A/C
. . . 24-16
HEATER CONTROL - INSTALLATION, A/C
. . 24-17
HEATER CONTROL - REMOVAL, A/C
......24-17
HEATER CORE - DESCRIPTION
..........24-52
HEATER CORE - INSTALLATION
.........24-53
HEATER CORE - OPERATION
............24-52
HEATER CORE - REMOVAL
.............24-52HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-6
HEATER SWITCH - DESCRIPTION,
DRIVER SEAT.......................8G-11
HEATER SWITCH - DESCRIPTION,
PASSENGER SEAT....................8G-14
HEATER SWITCH - INSTALLATION,
DRIVER SEAT.......................8G-13
HEATER SWITCH - INSTALLATION,
PASSENGER SEAT....................8G-15
HEATER SWITCH - OPERATION, DRIVER
SEAT ..............................8G-12
HEATER SWITCH - OPERATION,
PASSENGER SEAT....................8G-14
HEATER SWITCH - REMOVAL, DRIVER
SEAT ..............................8G-13
HEATER SWITCH - REMOVAL,
PASSENGER SEAT....................8G-15
HEATER-A/C CONTROL ILLUMINATION
BULB - INSTALLATION................8L-78
HEATER-A/C CONTROL ILLUMINATION
BULB - REMOVAL....................8L-78
HEATING GRID REPAIR - STANDARD
PROCEDURE, REAR GLASS.............8G-4
HEIGHT MEASUREMENT - STANDARD
PROCEDURE..........................2-4
HIGH AND LOW LIMITS - DESCRIPTION . . 25-20
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-22
HIGH BEAM INDICATOR - OPERATION....8J-22
HIGH BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP...................8L-34
HIGH BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-35
HIGH BEAM RELAY - OPERATION,
HEADLAMP.........................8L-33
HIGH BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-34
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER...................8L-18
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER...............8L-19
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER...................8L-19
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-42
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-42
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-17
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-18
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-18
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-18
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-18
HIGH/LOW RELAY - DESCRIPTION,
WIPER.............................8R-23
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-24
HIGH/LOW RELAY - INSTALLATION,
WIPER.............................8R-24
HIGH/LOW RELAY - OPERATION, WIPER . . 8R-23
HIGH/LOW RELAY - REMOVAL, WIPER . . . 8R-24
HINGE - INSTALLATION . . 23-119,23-123,23-131,
23-137
HINGE - REMOVAL......23-119,23-123,23-131,
23-137
HITCH - INSTALLATION, TRAILER.........13-9
HITCH - REMOVAL, TRAILER............13-9
HOISTING RECOMMENDATIONS -
STANDARD PROCEDURE.................0-4
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-17
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDING CLUTCHES - DESCRIPTION
....21-131
HOLDING CLUTCHES - OPERATION
.....21-132
HOLE REPAIR - DESCRIPTION,
THREADED
........................Intro.-4
HONING - STANDARD PROCEDURE,
CYLINDER BORE
......................9-39
HOOD - INSTALLATION
...............23-119HOOD - REMOVAL...................23-119
HOOD AJAR SWITCH - DESCRIPTION....8Q-11
HOOD AJAR SWITCH - DIAGNOSIS AND
TESTING...........................8Q-12
HOOD AJAR SWITCH - INSTALLATION....8Q-12
HOOD AJAR SWITCH - OPERATION......8Q-12
HOOD AJAR SWITCH - REMOVAL.......8Q-12
HOOD AJAR SWITCH BRACKET -
INSTALLATION......................8Q-13
HOOD AJAR SWITCH BRACKET -
REMOVAL..........................8Q-13
HOOD AJAR SWITCH STRIKER -
INSTALLATION......................8Q-14
HOOD AJAR SWITCH STRIKER -
REMOVAL..........................8Q-13
HOOK - INSTALLATION, FRONT TOW......13-8
HOOK - INSTALLATION, REAR TOW.......13-8
HOOK - REMOVAL, FRONT TOW..........13-8
HOOK - REMOVAL, REAR TOW...........13-8
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - REMOVAL....................8H-3
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION...........8H-3
HORN RELAY - REMOVAL..............8H-3
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING..............................8H-4
HORN SYSTEM - DESCRIPTION..........8H-1
HORN SYSTEM - DIAGNOSIS AND
TESTING............................8H-1
HORN SYSTEM - OPERATION............8H-1
HOSE - INSTALLATION, FRONT BRAKE.....5-10
HOSE - INSTALLATION, PRESSURE......19-21
HOSE - INSTALLATION, REAR BRAKE......5-10
HOSE - REMOVAL, FRONT...............5-9
HOSE - REMOVAL, PRESSURE..........19-21
HOSE - REMOVAL, REAR BRAKE..........5-9
HOSE CLAMPS - DESCRIPTION...........7-2
HOSE CLAMPS - OPERATION.............7-3
HOSE (GEAR TO THE COOLER) -
INSTALLATION, RETURN...............19-22
HOSE (GEAR TO THE COOLER) -
REMOVAL, RETURN..................19-21
HOSE (RESERVOIR TO THE COOLER) -
INSTALLATION, RETURN...............19-22
HOSE (RESERVOIR TO THE COOLER) -
REMOVAL, RETURN..................19-21
HOSES - DIAGNOSIS AND TESTING,
BRAKE LINE..........................5-8
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-40
HOSES/TUBES - DESCRIPTION, FRONT
WASHER
...........................8R-10
HOSES/TUBES - DESCRIPTION, REAR
WASHER
...........................8R-35
HOSES/TUBES - OPERATION, FRONT
WASHER
...........................8R-10
HOSES/TUBES - OPERATION, REAR
WASHER
...........................8R-36
HOUSING - ASSEMBLY, HVAC
...........24-34
HOUSING - DISASSEMBLY, HVAC
........24-34
HOUSING - INSTALLATION, HVAC
........24-34
HOUSING - REMOVAL, HVAC
...........24-33
HOUSING BUSHING - NV3550 -
INSTALLATION, EXTENSION
............21-74
HOUSING BUSHING - NV3550 -
REMOVAL, EXTENSION
................21-73
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER
................21-80
HOUSING SEAL - INSTALLATION,
ADAPTER
..........................21-124
HOUSING SEAL - NV1500 -
INSTALLATION, EXTENSION
............21-32
HOUSING SEAL - NV1500 - REMOVAL,
EXTENSION
.........................21-32
HOUSING SEAL - NV3550 -
INSTALLATION, EXTENSION
............21-74
HOUSING SEAL - NV3550 - REMOVAL,
EXTENSION
.........................21-74
HOUSING SEAL - REMOVAL, ADAPTER
. . 21-124
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION
.....................8W-01-1
HUB / BEARING - INSTALLATION
..........2-9
HUB / BEARING - REMOVAL
..............2-9
12 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

TANK - REMOVAL, FUEL...............14-25
TANK CHECK VALVE - DESCRIPTION,
FUEL..............................14-28
TANK CHECK VALVE - INSTALLATION,
FUEL..............................14-28
TANK CHECK VALVE - OPERATION, FUEL . . 14-28
TANK CHECK VALVE - REMOVAL, FUEL . . . 14-28
TANK SKID PLATE - INSTALLATION,
FUEL...............................13-9
TANK SKID PLATE - REMOVAL, FUEL......13-9
TASK MANAGER - DESCRIPTION........25-17
TASK MANAGER - OPERATION..........25-21
TCM QUICK LEARN - STANDARD
PROCEDURE........................8E-21
TEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-33
TEMP INDICATOR - OPERATION, TRANS . . 8J-34
TEMP SENSOR - DESCRIPTION,
AMBIENT...........................8M-9
TEMP SENSOR - OPERATION, AMBIENT . . . 8M-9
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-18
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-18
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT.....................7-19
TEMPERATURE SENSOR - DESCRIPTION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT...............8M-9
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-24
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-38
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-24
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-37
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT.....8M-9
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-36
TENSIONER - OPERATION, SEAT BELT....8O-36
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN................14-3
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE....................14-16
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY.....................14-15
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE....................14-15
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE...............21-79
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-11
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-14
TEST - STANDARD PROCEDURE, LOAD . . . 8F-12
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE
...............8F-12
TEST - STANDARD PROCEDURE,
VERIFICATION
........................8O-8
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION
..........................25-2
TEST MODE - DESCRIPTION, STATE
DISPLAY
............................25-2
TESTER - STANDARD PROCEDURE,
USING MIDTRONICS ELECTRICAL
.......8F-15TETHER ANCHOR - DESCRIPTION, CHILD . 8O-13
TETHER ANCHOR - OPERATION, CHILD . . . 8O-13
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-3
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-6
THERMAL GUARD - DESCRIPTION.......8F-20
THERMAL GUARD - INSTALLATION......8F-20
THERMAL GUARD - OPERATION.........8F-20
THERMAL GUARD - REMOVAL..........8F-20
THERMOSTAT - DIAGNOSIS AND
TESTING............................7-21
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-21
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM..............21-81
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-4
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN............9-9
THROTTLE BODY - DESCRIPTION........14-43
THROTTLE BODY - INSTALLATION.......14-44
THROTTLE BODY - OPERATION.........14-43
THROTTLE BODY - REMOVAL...........14-43
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-46
THROTTLE CONTROL CABLE - REMOVAL . . 14-45
THROTTLE POSITION SENSOR -
DESCRIPTION.........................14-47
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-48
THROTTLE POSITION SENSOR -
OPERATION.........................14-47
THROTTLE POSITION SENSOR -
REMOVAL..........................14-47
TIE ROD END - INSTALLATION..........19-16
TIE ROD END - REMOVAL..............19-16
TIE ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER.....................19-15
TIME INDICATOR - DESCRIPTION, FULL . . . 8J-29
TIME INDICATOR - DESCRIPTION, PART . . 8J-29
TIME INDICATOR - OPERATION, FULL....8J-30
TIME INDICATOR - OPERATION, PART....8J-29
TIMING - DESCRIPTION, VALVE..........9-71
TIMING - OPERATION, VALVE............9-71
TIMING - SPECIFICATIONS, IGNITION......8I-2
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........................9-76
TIMING BELT / CHAIN COVER(S) -
REMOVAL...........................9-74
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-71
TIRE - INSTALLATION, SPARE...........22-9
TIRE - REMOVAL, SPARE...............22-8
TIRE INFLATION - DIAGNOSIS AND
TESTING............................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE &TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL-PLY.......22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRES AND WHEEL RUNOUT -
DIAGNOSIS AND TESTING..............22-1
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . . 8W-01-9
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-5
TOOL, SPECIAL TOOLS - OUTER TIE
ROD END REMOVAL..................19-15
TOOLS - 3.7L ENGINE, SPECIAL
..........9-15
TOOLS - 8 1/4 AXLE, SPECIAL
...........3-98
TOOLS - BASE BRAKES, SPECIAL
.........5-7
TOOLS - BODY, SPECIAL
................23-5
TOOLS - COOLING, SPECIAL
.............7-14TOOLS - FRONT AXLE, SPECIAL..........3-34
TOOLS - FRONT SUSPENSION, SPECIAL....2-8
TOOLS - FUEL SYSTEM, SPECIAL........14-6
TOOLS - OUTER TIE ROD END REMOVAL
TOOL, SPECIAL......................19-15
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-20
TOOLS - REAR AXLE, SPECIAL...........3-63
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-120
TOOLS - STEERING COLUMN, SPECIAL....19-8
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, BATTERY SYSTEM - SPECIAL.....8F-7
TOOLS, SPECIFICATIONS - SPECIAL....3-12,3-6
TOOLS, SPECIFICATIONS - SPECIAL......8F-24
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-153
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-152
TORQUE - SPECIFICATIONS.............13-6
TORQUE CHART, SPECIFICATIONS . . 19-15,19-19,
19-8
TORQUE CHART, SPECIFICATIONS.....2-17,2-8
TORQUE CONVERTER - DESCRIPTION . . . 21-162
TORQUE CONVERTER - INSTALLATION . . . 21-167
TORQUE CONVERTER - OPERATION.....21-166
TORQUE CONVERTER - REMOVAL......21-167
TORQUE, EXCEPT DIESEL..............8F-23
TORQUE, GAS POWERED..............8F-38
TORQUE, IGNITION SYSTEM.............8I-3
TORQUE REFERENCES - DESCRIPTION . . Intro.-7
TORQUE, SPECIFICATIONS...............5-7
TORQUE, SPECIFICATIONS..............7-13
TORQUE, SPECIFICATIONS.............25-26
TORQUE, SPECIFICATIONS..............9-12
TORQUE, SPECIFICATIONS..............14-5
TORQUE, SPEED CONTROL.............8P-2
TOUCH-UP - DESCRIPTION, PAINT......23-163
TOW CONNECTOR - INSTALLATION,
TRAILER...........................8L-61
TOW CONNECTOR - REMOVAL, TRAILER . . 8L-61
TOW HOOK - INSTALLATION, FRONT......13-8
TOW HOOK - INSTALLATION, REAR.......13-8
TOW HOOK - REMOVAL, FRONT..........13-8
TOW HOOK - REMOVAL, REAR...........13-8
TOW RELAY - DESCRIPTION, TRAILER....8L-61
TOW RELAY - DIAGNOSIS AND TESTING,
TRAILER...........................8L-62
TOW RELAY - INSTALLATION, TRAILER . . . 8L-64
TOW RELAY - OPERATION, TRAILER.....8L-62
TOW RELAY - REMOVAL, TRAILER.......8L-63
TOW WIRING - DESCRIPTION, TRAILER . . 8L-64
TOWING - STANDARD PROCEDURE........0-6
TRACK - DESCRIPTION, SEAT..........8N-15
TRACK - DIAGNOSIS AND TESTING,
SEAT ..............................8N-16
TRACK - INSTALLATION, SEAT.........23-168
TRACK - INSTALLATION, SEAT..........8N-16
TRACK - OPERATION, SEAT............8N-15
TRACK - REMOVAL, SEAT.............23-168
TRACK - REMOVAL, SEAT..............8N-16
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - CLEANING, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-107,3-75
TRAC-LOK - INSPECTION, DIFFERENTIAL . 3-109,
3-77
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-106,
3-74
TRAILER HITCH - INSTALLATION.........13-9
TRAILER HITCH - REMOVAL.............13-9
TRAILER TOW CONNECTOR -
INSTALLATION.......................8L-61
TRAILER TOW CONNECTOR - REMOVAL . . 8L-61
TRAILER TOW RELAY - DESCRIPTION....8L-61
TRAILER TOW RELAY - DIAGNOSIS AND
TESTING...........................8L-62
TRAILER TOW RELAY - INSTALLATION . . . 8L-64
TRAILER TOW RELAY - OPERATION......8L-62
TRAILER TOW RELAY - REMOVAL
.......8L-63
TRAILER TOW WIRING - DESCRIPTION
. . . 8L-64
TRANS COOLER - DESCRIPTION
.........7-32
TRANS TEMP INDICATOR -
DESCRIPTION
.......................8J-33
TRANS TEMP INDICATOR - OPERATION
. . . 8J-34
KJINDEX 27
Description Group-Page Description Group-Page Description Group-Page

TRANSCEIVER MODULE - DESCRIPTION,
INTRUSION.........................8Q-14
TRANSCEIVER MODULE -
INSTALLATION, INTRUSION............8Q-16
TRANSCEIVER MODULE - OPERATION,
INTRUSION.........................8Q-15
TRANSCEIVER MODULE - REMOVAL,
INTRUSION.........................8Q-15
TRANSFER CASE - NV231 - ASSEMBLY . . 21-194
TRANSFER CASE - NV231 - CLEANING . . 21-190
TRANSFER CASE - NV231 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV231 -
DESCRIPTION......................21-178
TRANSFER CASE - NV231 - DIAGNOSIS
AND TESTING......................21-180
TRANSFER CASE - NV231 -
DISASSEMBLY......................21-182
TRANSFER CASE - NV231 - INSPECTION . 21-190
TRANSFER CASE - NV231 -
INSTALLATION......................21-205
TRANSFER CASE - NV231 - OPERATION . 21-179
TRANSFER CASE - NV231 - REMOVAL . . . 21-181
TRANSFER CASE - NV242 - ASSEMBLY . . 21-230
TRANSFER CASE - NV242 - CLEANING . . 21-227
TRANSFER CASE - NV242 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV242 -
DESCRIPTION......................21-215
TRANSFER CASE - NV242 - DIAGNOSIS
AND TESTING......................21-216
TRANSFER CASE - NV242 -
DISASSEMBLY......................21-218
TRANSFER CASE - NV242 - INSPECTION . 21-228
TRANSFER CASE - NV242 -
INSTALLATION......................21-243
TRANSFER CASE - NV242 - OPERATION . 21-215
TRANSFER CASE - NV242 - REMOVAL . . . 21-217
TRANSFER CASE, NV231.............21-206
TRANSFER CASE, NV242.............21-244
TRANSFER CASE SKID PLATE -
INSTALLATION........................13-7
TRANSFER CASE SKID PLATE -
REMOVAL...........................13-7
TRANSFER CASE, SPECIFICATIONS -
NV242............................21-244
TRANSMISSION - 45RFE -
DESCRIPTION, AUTOMATIC.............21-76
TRANSMISSION - 45RFE - OPERATION,
AUTOMATIC.........................21-77
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-2
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC.................21-77
TRANSMISSION - DIAGNOSIS AND
TESTING, MANUAL...............21-2,21-33
TRANSMISSION CLUTCH OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING..........................21-80
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-18
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-18
TRANSMISSION CONTROL RELAY -
DESCRIPTION......................21-168
TRANSMISSION CONTROL RELAY -
OPERATION........................21-168
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-128
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC...........................0-2
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - INSTALLATION....8L-83
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - REMOVAL........8L-82
TRANSMISSION RANGE SENSOR -
DESCRIPTION
......................21-168
TRANSMISSION RANGE SENSOR -
OPERATION
........................21-168
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DESCRIPTION, BRAKE
.......21-124
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DIAGNOSIS AND TESTING,
BRAKE
............................21-125
TRANSMISSION SHIFT INTERLOCK
SYSTEM - OPERATION, BRAKE
.........21-125TRANSMISSION SOLENOID/TRS
ASSEMBLY - DESCRIPTION............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - INSTALLATION...........21-170
TRANSMISSION SOLENOID/TRS
ASSEMBLY - OPERATION.............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - REMOVAL...............21-170
TRANSMISSION, SPECIAL TOOLS - RFE . . 21-120
TRANSMISSION, SPECIFICATIONS......21-119
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-170
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-170
TRANSMITTER - DESCRIPTION,
UNIVERSAL.........................8M-8
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-8
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL.................8M-8
TRANSMITTER - OPERATION,
UNIVERSAL.........................8M-8
TRANSMITTER - SPECIFICATIONS,
REMOTE KEYLESS ENTRY..............8N-9
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING................8M-8
TRANSMITTER CODES - STANDARD
PROCEDURE, SETTING.................8M-9
TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMING -
STANDARD PROCEDURE, RKE...........8N-9
TRANSPONDER KEY - DESCRIPTION.....8Q-18
TRANSPONDER KEY - OPERATION.......8Q-18
TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY KEY....8Q-8
TRAY - DESCRIPTION, BATTERY.........8F-21
TRAY - INSTALLATION, BATTERY........8F-21
TRAY - OPERATION, BATTERY..........8F-21
TRAY - REMOVAL, BATTERY............8F-21
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, B-PILLAR
LOWER...........................23-157
TRIM - INSTALLATION, B-PILLAR UPPER . 23-158
TRIM - REMOVAL, B-PILLAR LOWER....23-157
TRIM - REMOVAL, B-PILLAR UPPER....23-157
TRIM AND GRAB HANDLE -
INSTALLATION, A-PILLAR.............23-156
TRIM AND GRAB HANDLE - REMOVAL,
A-PILLAR..........................23-156
TRIM COVER - INSTALLATION, COWL . . . 23-157
TRIM COVER - REMOVAL, COWL.......23-157
TRIM LACE - INSTALLATION, OPENING . . 23-180
TRIM LACE - REMOVAL, OPENING......23-180
TRIM PANEL - INSTALLATION . . . 23-126,23-132,
23-138
TRIM PANEL - INSTALLATION, QUARTER . 23-159
TRIM PANEL - REMOVAL . 23-125,23-132,23-138
TRIM PANEL - REMOVAL, QUARTER....23-159
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-50
TUBE - INSTALLATION, A/C ORIFICE......24-50
TUBE - INSTALLATION, DRAIN.........23-181
TUBE - OPERATION, A/C ORIFICE........24-50
TUBE - REMOVAL, A/C ORIFICE.........24-50
TUBE - REMOVAL, DRAIN.............23-180
TURN SIGNAL INDICATOR -
DESCRIPTION.......................8J-34
TURN SIGNAL INDICATOR - OPERATION . . 8J-34
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT.............8O-38
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-37
UNIT - ADJUSTMENT, FRONT FOG LAMP . . 8L-25
UNIT - ADJUSTMENT, HEADLAMP
.......8L-42
UNIT - DIAGNOSIS AND TESTING, FUEL
LEVEL SENDING
......................14-9
UNIT - INSTALLATION, ASH RECEIVER
LAMP
..............................8L-72
UNIT - INSTALLATION, CARGO LAMP
.....8L-74
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP
................8L-19UNIT - INSTALLATION, COURTESY LAMP . . 8L-77
UNIT - INSTALLATION, FRONT FOG
LAMP..............................8L-25
UNIT - INSTALLATION, FRONT LAMP.....8L-28
UNIT - INSTALLATION, HEADLAMP.......8L-42
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-46
UNIT - INSTALLATION, READING LAMP . . . 8L-81
UNIT - INSTALLATION, REAR LAMP......8L-60
UNIT - INSTALLATION, REPEATER LAMP . . 8L-61
UNIT - REMOVAL, ASH RECEIVER LAMP . . 8L-72
UNIT - REMOVAL, CARGO LAMP........8L-74
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-19
UNIT - REMOVAL, COURTESY LAMP.....8L-76
UNIT - REMOVAL, FRONT FOG LAMP.....8L-25
UNIT - REMOVAL, FRONT LAMP.........8L-27
UNIT - REMOVAL, HEADLAMP..........8L-41
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-45
UNIT - REMOVAL, READING LAMP.......8L-81
UNIT - REMOVAL, REAR LAMP..........8L-59
UNIT - REMOVAL, REPEATER LAMP......8L-60
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING.....................14-10
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-9
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL TRANSMITTER -
DESCRIPTION........................8M-8
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING........................8M-8
UNIVERSAL TRANSMITTER - OPERATION . . 8M-8
UNLOCK SWITCH - INSTALLATION,
DOOR LOCK.........................8N-5
UNLOCK SWITCH - REMOVAL, DOOR
LOCK...............................8N-4
UPPER BALL JOINT - INSTALLATION......2-20
UPPER BALL JOINT - REMOVAL..........2-20
UPPER CONTROL ARM - INSTALLATION . . . 2-21
UPPER CONTROL ARM - REMOVAL.......2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - DESCRIPTION.........2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - OPERATION..........2-20
UPPER TRIM - INSTALLATION, B-PILLAR . 23-158
UPPER TRIM - REMOVAL, B-PILLAR....23-157
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-6 - ENGINE FIRING ORDER, 3.7L........8I-2
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-3
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-28
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-28
VACUUM LINES - DESCRIPTION.........25-33
VACUUM RESERVOIR - DESCRIPTION.....8P-7
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-7
VACUUM RESERVOIR - INSTALLATION....8P-8
VACUUM RESERVOIR - OPERATION.......8P-7
VACUUM RESERVOIR - REMOVAL........8P-7
VACUUM SYSTEM - DIAGNOSIS AND
TESTING............................24-6
VALUE - DESCRIPTION, LOAD..........25-20
VALVE - DESCRIPTION, FLOW
MANAGEMENT.......................14-6
VALVE - DESCRIPTION, FRONT CHECK....8R-8
VALVE - DESCRIPTION, FUEL TANK
CHECK.............................14-28
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - DESCRIPTION, PCV............25-29
VALVE - DESCRIPTION, REAR CHECK
....8R-34
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-161
VALVE - DESCRIPTION, VACUUM CHECK
. . 24-28
VALVE - DIAGNOSIS AND TESTING, PCV
. . 25-31
VALVE - DIAGNOSIS AND TESTING,
PROPORTIONING
.....................5-20
28 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

WHEELHOUSE SPLASH SHIELD -
INSTALLATION, REAR................23-144
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT...................23-143
WHEELHOUSE SPLASH SHIELD -
REMOVAL, REAR....................23-144
WHEELS - DESCRIPTION...............22-9
WHEELS - DIAGNOSIS AND TESTING.....22-10
WIND DEFLECTOR - INSTALLATION.....23-180
WIND DEFLECTOR - REMOVAL.........23-180
WIND NOISE - DIAGNOSIS AND TESTING . . 23-3
WIND NOISE DIAGNOSIS, DIAGNOSIS
AND TESTING - WATER DRAINAGE.....23-176
WINDOW - INSTALLATION, QUARTER . . . 23-172
WINDOW - REMOVAL, QUARTER.......23-172
WINDOW BAFFLE SEAL - INSTALLATION,
COWL/PLENUM.....................23-187
WINDOW BAFFLE SEAL - REMOVAL,
COWL/PLENUM.....................23-187
WINDOW DEFOGGER - DESCRIPTION,
REAR...............................8G-3
WINDOW DEFOGGER - OPERATION,
REAR...............................8G-3
WINDOW DEFOGGER FUNCTION -
DIAGNOSIS AND TESTING, REAR HVAC
CONTROL ASSEMBLY..................8G-9
WINDOW DEFOGGER GRID -
DESCRIPTION, REAR..................8G-5
WINDOW DEFOGGER GRID - DIAGNOSIS
AND TESTING, REAR..................8G-5
WINDOW DEFOGGER GRID -
OPERATION, REAR......................8G-5
WINDOW DEFOGGER RELAY -
DESCRIPTION, REAR..................8G-6
WINDOW DEFOGGER RELAY -
DIAGNOSIS AND TESTING, REAR.........8G-6
WINDOW DEFOGGER RELAY -
INSTALLATION, REAR..................8G-7
WINDOW DEFOGGER RELAY -
OPERATION, REAR....................8G-6
WINDOW DEFOGGER RELAY -
REMOVAL, REAR.....................8G-7
WINDOW DEFOGGER SWITCH -
DESCRIPTION, REAR..................8G-8
WINDOW DEFOGGER SWITCH -
DIAGNOSIS AND TESTING, REAR.........8G-8
WINDOW DEFOGGER SWITCH -
OPERATION, REAR....................8G-8
WINDOW DEFOGGER SYSTEM -
DIAGNOSIS AND TESTING, REAR.........8G-4
WINDOW MOTOR - REMOVAL..........8N-22WINDOW REGULATOR - ELECTRIC -
INSTALLATION................23-126,23-134
WINDOW REGULATOR - ELECTRIC -
REMOVAL...................23-126,23-134
WINDOW REGULATOR - MANUAL -
INSTALLATION................23-126,23-133
WINDOW REGULATOR - MANUAL -
REMOVAL...................23-126,23-133
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-22
WINDOW SWITCH - INSTALLATION......8N-23
WINDOW SWITCH - REMOVAL..........8N-23
WINDOWS - DESCRIPTION, POWER.....8N-21
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-21
WINDOWS - OPERATION, POWER.......8N-21
WINDSHIELD A-PILLAR WEATHERSTRIP/
RETAINER - INSTALLATION............23-187
WINDSHIELD A-PILLAR WEATHERSTRIP/
RETAINER - REMOVAL...............23-186
WINDSHIELD SAFETY PRECAUTIONS,
WARNING.........................23-173
WIPER & WASHER SYSTEM -
CLEANING, FRONT....................8R-7
WIPER & WASHER SYSTEM -
CLEANING, REAR....................8R-32
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING, FRONT........8R-6
WIPER & WASHER SYSTEM -
DIAGNOSIS AND TESTING, REAR........8R-30
WIPER & WASHER SYSTEM -
INSPECTION, FRONT...................8R-7
WIPER & WASHER SYSTEM -
INSPECTION, REAR...................8R-33
WIPER ARM - DESCRIPTION, FRONT.....8R-12
WIPER ARM - DESCRIPTION, REAR......8R-37
WIPER ARM - INSTALLATION, FRONT....8R-13
WIPER ARM - INSTALLATION, REAR.....8R-38
WIPER ARM - OPERATION, FRONT......8R-12
WIPER ARM - OPERATION, REAR.......8R-38
WIPER ARM - REMOVAL, FRONT........8R-12
WIPER ARM - REMOVAL, REAR.........8R-38
WIPER ARM PARK RAMP -
INSTALLATION......................8R-43
WIPER ARM PARK RAMP - REMOVAL....8R-43
WIPER BLADE - DESCRIPTION, FRONT . . . 8R-13
WIPER BLADE - DESCRIPTION, REAR....8R-39
WIPER BLADE - INSTALLATION, FRONT . . . 8R-14
WIPER BLADE - INSTALLATION, REAR....8R-40
WIPER BLADE - OPERATION, FRONT.....8R-14
WIPER BLADE - OPERATION, REAR......8R-39WIPER BLADE - REMOVAL, FRONT......8R-14
WIPER BLADE - REMOVAL, REAR.......8R-40
WIPER HIGH/LOW RELAY -
DESCRIPTION.......................8R-23
WIPER HIGH/LOW RELAY - DIAGNOSIS
AND TESTING.......................8R-24
WIPER HIGH/LOW RELAY -
INSTALLATION......................8R-24
WIPER HIGH/LOW RELAY - OPERATION . . 8R-23
WIPER HIGH/LOW RELAY - REMOVAL....8R-24
WIPER MODULE - DESCRIPTION, FRONT . 8R-15
WIPER MODULE - INSTALLATION,
FRONT.............................8R-16
WIPER MODULE - OPERATION, FRONT . . . 8R-15
WIPER MODULE - REMOVAL, FRONT....8R-16
WIPER MOTOR - DESCRIPTION, REAR . . . 8R-41
WIPER MOTOR - INSTALLATION, REAR . . . 8R-42
WIPER MOTOR - OPERATION, REAR.....8R-41
WIPER MOTOR - REMOVAL, REAR......8R-42
WIPER ON/OFF RELAY - DESCRIPTION . . . 8R-25
WIPER ON/OFF RELAY - DIAGNOSIS AND
TESTING...........................8R-26
WIPER ON/OFF RELAY - INSTALLATION . . . 8R-26
WIPER ON/OFF RELAY - OPERATION.....8R-25
WIPER ON/OFF RELAY - REMOVAL......8R-26
WIPERS/WASHERS - DESCRIPTION,
FRONT..............................8R-2
WIPERS/WASHERS - DESCRIPTION,
REAR...............................8R-27
WIPERS/WASHERS - OPERATION,
FRONT..............................8R-4
WIPERS/WASHERS - OPERATION, REAR . . 8R-29
WIPER/WASHER SWITCH -
DESCRIPTION, FRONT................8R-16
WIPER/WASHER SWITCH -
DESCRIPTION, REAR.................8R-43
WIPER/WASHER SWITCH - OPERATION,
FRONT.............................8R-16
WIPER/WASHER SWITCH - OPERATION,
REAR..............................8R-43
WIRE SPLICING - STANDARD
PROCEDURE.....................8W-01-14
WIRING - DESCRIPTION, TRAILER TOW . . 8L-64
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE .....................8W-01-1
WIRING HARNESS - DIAGNOSIS AND
TESTING.........................8W-01-7
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD
PROCEDURE, REPAIR DAMAGED OR.......9-9
30 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page