2002 JEEP LIBERTY turn indicators

ENGINE - 2.4L
DESCRIPTION
The 2.4 Liter (148 cu. in.) in-line four cylinder
engine is a double over head camshaft with hydraulic
lifters and four valve per cylinder design. The engine
is free-wheeling; meaning it has provisions for piston-
to-valve clearance. However valve-to-valve interference
can occur, if camshafts are rotated independently.
The cylinders are numbered from front of the
engine to the rear. The firing order is 1±3±4±2.
The engine identification number is located on the
rear of the cylinder block (Fig. 1).
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - CYLINDER
COMBUSTION PRESSURE LEAKAGE TEST
The combustion pressure leakage test provides an
accurate means for determining engine condition.
Combustion pressure leakage testing will detect:
²Exhaust and intake valve leaks (improper seat-
ing).
²Leaks between adjacent cylinders or into water
jacket.
²Any causes for combustion/compression pressure
loss.WARNING: DO NOT REMOVE THE PRESSURE CAP
WITH THE SYSTEM HOT AND UNDER PRESSURE
BECAUSE SERIOUS BURNS FROM COOLANT CAN
OCCUR.
Check the coolant level and fill as required. DO
NOT install the pressure cap.
Start and operate the engine until it attains nor-
mal operating temperature, then turn the engine
OFF.
Clean spark plug recesses with compressed air.
Remove the spark plugs.
Remove the oil filler cap.
Remove the air cleaner.
Calibrate the tester according to the manufactur-
er's instructions. The shop air source for testing
should maintain 483 kPa (70 psi) minimum, 1,379
kPa (200 psi) maximum, with 552 kPa (80 psi) rec-
ommended.
Perform the test procedures on each cylinder
according to the tester manufacturer's instructions.
While testing, listen for pressurized air escaping
through the throttle body, tailpipe and oil filler cap
opening. Check for bubbles in the coolant.
All gauge pressure indications should be equal,
with no more than 25% leakage per cylinder.
FOR EXAMPLE:At 552 kPa (80 psi) input pres-
sure, a minimum of 414 kPa (60 psi) should be main-
tained in the cylinder.
DIAGNOSIS AND TESTING - CYLINDER
COMPRESSION PRESSURE TEST
The results of a cylinder compression pressure test
can be utilized to diagnose several engine malfunc-
tions.
Ensure the battery is completely charged and the
engine starter motor is in good operating condition.
Otherwise the indicated compression pressures may
not be valid for diagnosis purposes.
(1) Check engine oil level and add oil if necessary.
(2) Drive the vehicle until engine reaches normal
operating temperature. Select a route free from traf-
fic and other forms of congestion, observe all traffic
laws, and accelerate through the gears several times
briskly.
(3) Remove all spark plugs from engine. As spark
plugs are being removed, check electrodes for abnor-
mal firing indicators fouled, hot, oily, etc. Record cyl-
inder number of spark plug for future reference.
(4) Remove the Auto Shutdown (ASD) relay from
the PDC.
(5) Be sure throttle blade is fully open during the
compression check.
(6) Insert compression gage adaptor Special Tool
8116 or the equivalent, into the #1 spark plug hole in
cylinder head. Connect the 0±500 psi (Blue) pressure
transducer with cable adaptors to the DRBIIIt.
Fig. 1 ENGINE IDENTIFICATION
1 - ENGINE IDENTIFICATION
KJENGINE9s-3

HVAC CONTROL ASSEMBLY WINDOW
DEFOGGER FUNCTION - DIAGNOSIS
AND TESTING, REAR..................8G-9
HVAC HOUSING - ASSEMBLY...........24-34
HVAC HOUSING - DISASSEMBLY........24-34
HVAC HOUSING - INSTALLATION........24-34
HVAC HOUSING - REMOVAL............24-33
HYDRAULIC LASH ADJUSTER -
DIAGNOSIS AND TESTING..........9-19,9-30
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING.............21-79
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS....................21-100
HYDROMETER TEST - STANDARD
PROCEDURE........................8F-11
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-1
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-6
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-8
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-35
IDLE AIR CONTROL MOTOR -
INSTALLATION.......................14-36
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-35
IDLE AIR CONTROL MOTOR - REMOVAL . . 14-36
IDLER SHAFT - INSTALLATION...........9-77
IDLER SHAFT - REMOVAL...............9-77
IGNITION CIRCUIT SENSE -
DESCRIPTION.........................8E-13
IGNITION CIRCUIT SENSE - OPERATION . . 8E-15
IGNITION COIL - DESCRIPTION...........8I-9
IGNITION COIL - INSTALLATION.........8I-10
IGNITION COIL - OPERATION.............8I-9
IGNITION COIL - REMOVAL.............8I-10
IGNITION COIL CAPACITOR -
DESCRIPTION........................8I-16
IGNITION COIL CAPACITOR -
INSTALLATION.......................8I-16
IGNITION COIL CAPACITOR - OPERATION . . 8I-16
IGNITION COIL CAPACITOR - REMOVAL . . . 8I-16
IGNITION COIL RESISTANCE, 2.4L.........8I-2
IGNITION COIL RESISTANCE, 3.7L V-6.....8I-3
IGNITION CONTROL - DESCRIPTION.......8I-1
IGNITION CONTROL - OPERATION.........8I-1
IGNITION SWITCH - DESCRIPTION........19-8
IGNITION SWITCH - DESCRIPTION,
KEY-IN.............................19-10
IGNITION SWITCH - DIAGNOSIS AND
TESTING............................19-8
IGNITION SWITCH - DIAGNOSIS AND
TESTING, KEY-IN.....................19-10
IGNITION SWITCH INSTALLATION,
INSTALLATION........................19-9
IGNITION SWITCH REMOVAL, REMOVAL . . . 19-9
IGNITION SYSTEM - TORQUE............8I-3
IGNITION TIMING - SPECIFICATIONS......8I-2
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-14
ILLUMINATION BULB - INSTALLATION,
COMPASS MINI-TRIP
.................8L-75
ILLUMINATION BULB - INSTALLATION,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - INSTALLATION,
TRANSMISSION RANGE INDICATOR
......8L-83
ILLUMINATION BULB - REMOVAL,
COMPASS MINI-TRIP
.................8L-74
ILLUMINATION BULB - REMOVAL,
HEATER-A/C CONTROL
................8L-78
ILLUMINATION BULB - REMOVAL,
TRANSMISSION RANGE INDICATOR
......8L-82
IMMOBILIZER MODULE - DESCRIPTION,
SENTRY KEY
........................8E-15
IMMOBILIZER MODULE - INSTALLATION,
SENTRY KEY
........................8E-18
IMMOBILIZER MODULE - OPERATION,
SENTRY KEY
........................8E-16
IMMOBILIZER MODULE - REMOVAL,
SENTRY KEY
........................8E-17
IMPACT AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE
..................8O-43
IMPACT AIRBAG CONTROL MODULE -
INSTALLATION, SIDE
.................8O-45
IMPACT AIRBAG CONTROL MODULE -
OPERATION, SIDE
....................8O-43IMPACT AIRBAG CONTROL MODULE -
REMOVAL, SIDE.....................8O-44
IMPACT SENSOR - DESCRIPTION,
FRONT.............................8O-21
IMPACT SENSOR - INSTALLATION,
FRONT.............................8O-22
IMPACT SENSOR - OPERATION, FRONT . . . 8O-21
IMPACT SENSOR - REMOVAL, FRONT....8O-22
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF............21-125
INDICATOR - DESCRIPTION, ABS........8J-11
INDICATOR - DESCRIPTION, AIRBAG.....8J-12
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-13
INDICATOR - DESCRIPTION, CHARGING . . . 8J-15
INDICATOR - DESCRIPTION, COOLANT
LOW...............................8J-15
INDICATOR - DESCRIPTION, CRUISE.....8J-16
INDICATOR - DESCRIPTION, DOOR AJAR . . 8J-17
INDICATOR - DESCRIPTION, FOUR LOW
MODE.............................8J-29
INDICATOR - DESCRIPTION, FRONT FOG
LAMP..............................8J-19
INDICATOR - DESCRIPTION, FULL TIME . . . 8J-29
INDICATOR - DESCRIPTION, GATE AJAR . . 8J-20
INDICATOR - DESCRIPTION, GLASS
AJAR..............................8J-21
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-22
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, LOW OIL
PRESSURE..........................8J-23
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, PART TIME . . 8J-29
INDICATOR - DESCRIPTION, REAR FOG
LAMP..............................8J-27
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SECURITY . . . 8J-28
INDICATOR - DESCRIPTION, SKIS........8J-31
INDICATOR - DESCRIPTION, TRANS
TEMP..............................8J-33
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-34
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-35
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-37
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-14
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID......................8J-36
INDICATOR - OPERATION, ABS..........8J-11
INDICATOR - OPERATION, AIRBAG.......8J-12
INDICATOR - OPERATION, BRAKE/PARK
BRAKE.............................8J-13
INDICATOR - OPERATION, CHARGING....8J-15
INDICATOR - OPERATION, COOLANT
LOW...............................8J-16
INDICATOR - OPERATION, CRUISE.......8J-17
INDICATOR - OPERATION, DOOR AJAR . . . 8J-17
INDICATOR - OPERATION, FOUR LOW
MODE.............................8J-30
INDICATOR - OPERATION, FRONT FOG
LAMP..............................8J-19
INDICATOR - OPERATION, FULL TIME....8J-30
INDICATOR - OPERATION, GATE AJAR....8J-20
INDICATOR - OPERATION, GLASS AJAR . . . 8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-22
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, LOW OIL
PRESSURE
..........................8J-23
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, PART TIME
....8J-29
INDICATOR - OPERATION, REAR FOG
LAMP
..............................8J-27
INDICATOR - OPERATION, SEATBELT
.....8J-28
INDICATOR - OPERATION, SECURITY
.....8J-28
INDICATOR - OPERATION, SKIS
.........8J-31
INDICATOR - OPERATION, TRANS TEMP
. . 8J-34
INDICATOR - OPERATION, TURN SIGNAL
. . 8J-34
INDICATOR - OPERATION, WAIT-TO-
START
.............................8J-35
INDICATOR - OPERATION, WASHER
FLUID
..............................8J-36INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-37
INDICATOR ILLUMINATION BULB -
INSTALLATION, TRANSMISSION
RANGE.............................8L-83
INDICATOR ILLUMINATION BULB -
REMOVAL, TRANSMISSION RANGE......8L-82
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-24
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-24
INDICATOR TEST - STANDARD
PROCEDURE, BUILT-IN................8F-10
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION - DIAGNOSIS AND TESTING,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-18
INITIALIZATION - STANDARD
PROCEDURE, SKIS....................8Q-8
INJECTION - DESCRIPTION, FUEL........14-29
INJECTOR - DESCRIPTION, FUEL........14-33
INJECTOR - DIAGNOSIS AND TESTING,
FUEL..............................14-33
INJECTOR - OPERATION, FUEL..........14-33
INLET FILTER - INSTALLATION..........14-28
INLET FILTER - REMOVAL..............14-28
INPUT - OPERATION, ASD SENSE - PCM . . . 8I-4
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-138
INPUT CLUTCH ASSEMBLY -
DESCRIPTION......................21-133
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY......................21-135
INPUT CLUTCH ASSEMBLY - OPERATION . 21-135
INPUT SPEED SENSOR - DESCRIPTION . . 21-143
INPUT SPEED SENSOR - INSTALLATION . 21-143
INPUT SPEED SENSOR - OPERATION....21-143
INPUT SPEED SENSOR - REMOVAL.....21-143
INSTRUMENT CLUSTER - ASSEMBLY.....8J-10
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - DISASSEMBLY . . . 8J-9
INSTRUMENT CLUSTER - INSTALLATION . . 8J-11
INSTRUMENT CLUSTER - OPERATION.....8J-4
INSTRUMENT CLUSTER - REMOVAL......8J-9
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-8
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-7
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION......................23-151
INSTRUMENT PANEL ASSEMBLY -
REMOVAL.........................23-149
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION......................23-154
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL.........................23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - INSTALLATION..............23-154
INSTRUMENT PANEL DRIVER SIDE
BEZELS - REMOVAL.................23-153
INSTRUMENT PANEL END CAP -
INSTALLATION
......................23-153
INSTRUMENT PANEL END CAP -
REMOVAL
.........................23-153
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - INSTALLATION
...............23-154
INSTRUMENT PANEL PASSENGER SIDE
BEZEL - REMOVAL
..................23-154
INSTRUMENT PANEL TOP COVER -
INSTALLATION
......................23-153
INSTRUMENT PANEL TOP COVER -
REMOVAL
.........................23-152
INTAKE AIR TEMPERATURE SENSOR -
DESCRIPTION
.......................14-36
INTAKE AIR TEMPERATURE SENSOR -
INSTALLATION
.......................14-38
INTAKE AIR TEMPERATURE SENSOR -
OPERATION
.........................14-36
INTAKE AIR TEMPERATURE SENSOR -
REMOVAL
..........................14-37
INTAKE MANIFOLD - DESCRIPTION
.......9-68
INTAKE MANIFOLD - INSTALLATION
.......9-69
INTAKE MANIFOLD - REMOVAL
..........9-68
KJINDEX 13
Description Group-Page Description Group-Page Description Group-Page

TRANSCEIVER MODULE - DESCRIPTION,
INTRUSION.........................8Q-14
TRANSCEIVER MODULE -
INSTALLATION, INTRUSION............8Q-16
TRANSCEIVER MODULE - OPERATION,
INTRUSION.........................8Q-15
TRANSCEIVER MODULE - REMOVAL,
INTRUSION.........................8Q-15
TRANSFER CASE - NV231 - ASSEMBLY . . 21-194
TRANSFER CASE - NV231 - CLEANING . . 21-190
TRANSFER CASE - NV231 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV231 -
DESCRIPTION......................21-178
TRANSFER CASE - NV231 - DIAGNOSIS
AND TESTING......................21-180
TRANSFER CASE - NV231 -
DISASSEMBLY......................21-182
TRANSFER CASE - NV231 - INSPECTION . 21-190
TRANSFER CASE - NV231 -
INSTALLATION......................21-205
TRANSFER CASE - NV231 - OPERATION . 21-179
TRANSFER CASE - NV231 - REMOVAL . . . 21-181
TRANSFER CASE - NV242 - ASSEMBLY . . 21-230
TRANSFER CASE - NV242 - CLEANING . . 21-227
TRANSFER CASE - NV242 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV242 -
DESCRIPTION......................21-215
TRANSFER CASE - NV242 - DIAGNOSIS
AND TESTING......................21-216
TRANSFER CASE - NV242 -
DISASSEMBLY......................21-218
TRANSFER CASE - NV242 - INSPECTION . 21-228
TRANSFER CASE - NV242 -
INSTALLATION......................21-243
TRANSFER CASE - NV242 - OPERATION . 21-215
TRANSFER CASE - NV242 - REMOVAL . . . 21-217
TRANSFER CASE, NV231.............21-206
TRANSFER CASE, NV242.............21-244
TRANSFER CASE SKID PLATE -
INSTALLATION........................13-7
TRANSFER CASE SKID PLATE -
REMOVAL...........................13-7
TRANSFER CASE, SPECIFICATIONS -
NV242............................21-244
TRANSMISSION - 45RFE -
DESCRIPTION, AUTOMATIC.............21-76
TRANSMISSION - 45RFE - OPERATION,
AUTOMATIC.........................21-77
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-2
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC.................21-77
TRANSMISSION - DIAGNOSIS AND
TESTING, MANUAL...............21-2,21-33
TRANSMISSION CLUTCH OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING..........................21-80
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-18
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-18
TRANSMISSION CONTROL RELAY -
DESCRIPTION......................21-168
TRANSMISSION CONTROL RELAY -
OPERATION........................21-168
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-128
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC...........................0-2
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - INSTALLATION....8L-83
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - REMOVAL........8L-82
TRANSMISSION RANGE SENSOR -
DESCRIPTION
......................21-168
TRANSMISSION RANGE SENSOR -
OPERATION
........................21-168
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DESCRIPTION, BRAKE
.......21-124
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DIAGNOSIS AND TESTING,
BRAKE
............................21-125
TRANSMISSION SHIFT INTERLOCK
SYSTEM - OPERATION, BRAKE
.........21-125TRANSMISSION SOLENOID/TRS
ASSEMBLY - DESCRIPTION............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - INSTALLATION...........21-170
TRANSMISSION SOLENOID/TRS
ASSEMBLY - OPERATION.............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - REMOVAL...............21-170
TRANSMISSION, SPECIAL TOOLS - RFE . . 21-120
TRANSMISSION, SPECIFICATIONS......21-119
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-170
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-170
TRANSMITTER - DESCRIPTION,
UNIVERSAL.........................8M-8
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-8
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL.................8M-8
TRANSMITTER - OPERATION,
UNIVERSAL.........................8M-8
TRANSMITTER - SPECIFICATIONS,
REMOTE KEYLESS ENTRY..............8N-9
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING................8M-8
TRANSMITTER CODES - STANDARD
PROCEDURE, SETTING.................8M-9
TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMING -
STANDARD PROCEDURE, RKE...........8N-9
TRANSPONDER KEY - DESCRIPTION.....8Q-18
TRANSPONDER KEY - OPERATION.......8Q-18
TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY KEY....8Q-8
TRAY - DESCRIPTION, BATTERY.........8F-21
TRAY - INSTALLATION, BATTERY........8F-21
TRAY - OPERATION, BATTERY..........8F-21
TRAY - REMOVAL, BATTERY............8F-21
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, B-PILLAR
LOWER...........................23-157
TRIM - INSTALLATION, B-PILLAR UPPER . 23-158
TRIM - REMOVAL, B-PILLAR LOWER....23-157
TRIM - REMOVAL, B-PILLAR UPPER....23-157
TRIM AND GRAB HANDLE -
INSTALLATION, A-PILLAR.............23-156
TRIM AND GRAB HANDLE - REMOVAL,
A-PILLAR..........................23-156
TRIM COVER - INSTALLATION, COWL . . . 23-157
TRIM COVER - REMOVAL, COWL.......23-157
TRIM LACE - INSTALLATION, OPENING . . 23-180
TRIM LACE - REMOVAL, OPENING......23-180
TRIM PANEL - INSTALLATION . . . 23-126,23-132,
23-138
TRIM PANEL - INSTALLATION, QUARTER . 23-159
TRIM PANEL - REMOVAL . 23-125,23-132,23-138
TRIM PANEL - REMOVAL, QUARTER....23-159
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-50
TUBE - INSTALLATION, A/C ORIFICE......24-50
TUBE - INSTALLATION, DRAIN.........23-181
TUBE - OPERATION, A/C ORIFICE........24-50
TUBE - REMOVAL, A/C ORIFICE.........24-50
TUBE - REMOVAL, DRAIN.............23-180
TURN SIGNAL INDICATOR -
DESCRIPTION.......................8J-34
TURN SIGNAL INDICATOR - OPERATION . . 8J-34
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT.............8O-38
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-37
UNIT - ADJUSTMENT, FRONT FOG LAMP . . 8L-25
UNIT - ADJUSTMENT, HEADLAMP
.......8L-42
UNIT - DIAGNOSIS AND TESTING, FUEL
LEVEL SENDING
......................14-9
UNIT - INSTALLATION, ASH RECEIVER
LAMP
..............................8L-72
UNIT - INSTALLATION, CARGO LAMP
.....8L-74
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP
................8L-19UNIT - INSTALLATION, COURTESY LAMP . . 8L-77
UNIT - INSTALLATION, FRONT FOG
LAMP..............................8L-25
UNIT - INSTALLATION, FRONT LAMP.....8L-28
UNIT - INSTALLATION, HEADLAMP.......8L-42
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-46
UNIT - INSTALLATION, READING LAMP . . . 8L-81
UNIT - INSTALLATION, REAR LAMP......8L-60
UNIT - INSTALLATION, REPEATER LAMP . . 8L-61
UNIT - REMOVAL, ASH RECEIVER LAMP . . 8L-72
UNIT - REMOVAL, CARGO LAMP........8L-74
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-19
UNIT - REMOVAL, COURTESY LAMP.....8L-76
UNIT - REMOVAL, FRONT FOG LAMP.....8L-25
UNIT - REMOVAL, FRONT LAMP.........8L-27
UNIT - REMOVAL, HEADLAMP..........8L-41
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-45
UNIT - REMOVAL, READING LAMP.......8L-81
UNIT - REMOVAL, REAR LAMP..........8L-59
UNIT - REMOVAL, REPEATER LAMP......8L-60
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING.....................14-10
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-9
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL TRANSMITTER -
DESCRIPTION........................8M-8
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING........................8M-8
UNIVERSAL TRANSMITTER - OPERATION . . 8M-8
UNLOCK SWITCH - INSTALLATION,
DOOR LOCK.........................8N-5
UNLOCK SWITCH - REMOVAL, DOOR
LOCK...............................8N-4
UPPER BALL JOINT - INSTALLATION......2-20
UPPER BALL JOINT - REMOVAL..........2-20
UPPER CONTROL ARM - INSTALLATION . . . 2-21
UPPER CONTROL ARM - REMOVAL.......2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - DESCRIPTION.........2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - OPERATION..........2-20
UPPER TRIM - INSTALLATION, B-PILLAR . 23-158
UPPER TRIM - REMOVAL, B-PILLAR....23-157
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-6 - ENGINE FIRING ORDER, 3.7L........8I-2
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-3
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-28
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-28
VACUUM LINES - DESCRIPTION.........25-33
VACUUM RESERVOIR - DESCRIPTION.....8P-7
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-7
VACUUM RESERVOIR - INSTALLATION....8P-8
VACUUM RESERVOIR - OPERATION.......8P-7
VACUUM RESERVOIR - REMOVAL........8P-7
VACUUM SYSTEM - DIAGNOSIS AND
TESTING............................24-6
VALUE - DESCRIPTION, LOAD..........25-20
VALVE - DESCRIPTION, FLOW
MANAGEMENT.......................14-6
VALVE - DESCRIPTION, FRONT CHECK....8R-8
VALVE - DESCRIPTION, FUEL TANK
CHECK.............................14-28
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - DESCRIPTION, PCV............25-29
VALVE - DESCRIPTION, REAR CHECK
....8R-34
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-161
VALVE - DESCRIPTION, VACUUM CHECK
. . 24-28
VALVE - DIAGNOSIS AND TESTING, PCV
. . 25-31
VALVE - DIAGNOSIS AND TESTING,
PROPORTIONING
.....................5-20
28 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page