2002 HONDA S2000 ECU

The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If Honda MTF is not available, you
may use an API service SG, SH or SJ
grade motor oil with a viscosity of
SAE 10W-30 or 10W-40 as a
temporary replacement. An SG
grade is pref erred, but an SH or SJ
grade may be used if SG is not
available. However, motor oil does
not contain the proper additives and
continued use can cause stif f er
shif ting. Replace as soon as it is
convenient.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual Transmis-
sion Fluid (MTF) until it starts to
run out of the hole. Reinstall the
f iller bolt and tighten it securely.
Maint enance
6-speed Manual T ransmission Fluid
174
FFIILLLLEERRBBOOLLTT
CCOORRRREECCTTLLEEVVEELL

Put a new washer on the f iller bolt,
then reinstall the f iller bolt. Tighten
it securely. Tightening torque:
The dif f erential should be drained
and ref illed with new f luid according
to the time and distance
recommendations in the
maintenance schedule.
Check the f luid level with the
dif f erential at normal operating
temperature and the vehicle sitting
on level ground. Remove the
dif f erential f luid f iller bolt and
washer and caref ully f eel inside the
bolt hole with your f inger. The f luid
level should be up to the edge of the
bolt hole. If it is not, slowly add f luid
until it starts to run out of the hole. UseaSAE90viscosityhypoidgear
oil, API service classif ied GL5 or
GL6 only, in the dif f erential.
Maint enance
Dif f erential Fluid
175
FFIILLLLEERRBBOOLLTT
CCOORRRREECCTTLLEEVVEELL33 lbf·ft (45 N·m , 4.6 kgf·m)

Install the new bulb in the socket.
Testthelightstomakesurethe
new bulb is working.
Push the socket into the light
assembly and turn it clockwise
until it locks.
Install the trunk lining and secure
it with the fasteners. To reinstall a
f astener, reset the f astener by
pushing on the pointed end until it
pops back almost f lush with the
f ingers on the housing. Put the
f astener in the hole of the trunk
lining and push on the center until
it locks (the center is flush with
the head).
7. 8. 9.
10.
Lights
Maint enance205

Clean the windows, inside and out,
with a commercially-available glass
cleaner. You can also use a mixture
of one part white vinegar to ten parts
water. This will remove the haze that
builds up on the inside of the
windows. Use a sof t cloth or paper
towels to clean all glass and clear
plastic surf aces. If you use a liquid air f reshener,make sure you f asten it securely so it
does not spill as you drive.Two f actors normally contribute to
causing corrosion in your car:
Moisture trapped in body cavities.
Dirtandroadsaltthatcollectsin
hollowsontheundersideof the
car stays damp, promoting
corrosion in that area.
Removal of paint and protective
coatings f rom the exterior and
underside of the car.
If you want to use an air f reshener/
deodorizer in the interior of your car,
it is best to use a solid type. Some
liquid air f resheners contain chemi-
cals that may cause parts of the
interior trim and f abric to crack or
discolor.
If you get any glass cleaner on the
convertible top, immediately spray
the area with water, and dry it with a
sof t cloth. 1. 2.
Windows A ir Fresheners Corrosion Protection
Int erior Care, Corrosion Prot ect ion
Appearance Care
215
The rear window def ogger is bonded to
the inside of the glass. Wiping
vigorously up-and-down can dislodge
and break these wires. When cleaning
therearwindow,usegentlepressure
and wipe side-to-side.

Put on the spare tire. Put the
wheel nuts back on f inger-tight,
then tighten them in a crisscross
pattern with the wheel wrench
until the wheel is f irmly against
the hub. Do not try to tighten
them f ully.Lower the car to the ground and
remove the jack.
Tighten the wheel nuts securely in
the same crisscross pattern. Have
the wheel nut torque checked at
the nearest automotive service
f acility.
Tighten the wheel nuts to:
13.
11. 12.
Changing a Flat T ire
T aking Care of t he Unexpect ed
224 80 lbf·ft (108 N·m , 11 kgf·m)

Remove the tool box f rom the
trunk well and replace the jack,
wheel wrench and extension in the
tool box.
Place the tool box into the spare
tire shelf in the trunk.Replacethesparetirecover.
Secure it with the three clips. Push
each clip down securely, and pivot
theringdownflat.
Put the flat tire in the trunk well
vertically as shown.
14.
15. 17.
16.
Changing a Flat T ire
T aking Care of t he Unexpect ed
225

Screw the towing hook into the
extension and tighten it securely
by hand.
4.
If Your Car Gets Stuck
T aking Care of t he Unexpect ed
246
To avoid damage to your car, use the
towing hook f or straight, f lat ground
towing only. Do not tow at an angle.
The tow hook should not be used to tow
the vehicle onto a f lat bed. Do not use
it as a tie down.