2002 HONDA S2000 clock

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.Pull the inner f ender cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Install the new bulb in the socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender in place.
Install the two holding clips. Lock
each clip in place by pushing on
the center.
Use a f lat-tipped screwdriver to
remove the three holding clips
f rom the inner f ender.
1.
2. 3. 4. 5.6. 7. 8. 9.
Lights
Maint enance
Replacing Front Turn Signal and
Side Marker L ight Bulbs 202

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Put the bulb holder back into its
hole in the lens, and turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
Use a small f lat blade screwdriver
to pry caref ully on the back edge
of the side turn signal assembly
until it pops out of the body.
Turn the bulb holder one-quarter
turn counterclockwise to remove it
from the lens. Put the side turn signal assembly
back into the body, front first.
Push on the back edge until it
snaps into place.
1. 2. 3. 4. 5. 6.
Lights
Maint enance
Replacing a Side T urn Signal Bulb
203

Open the trunk. Determine which of the f our bulbsis burned out: stop/taillight, back-
up light, turn signal, or side
marker.Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the fasteners from the
trunk lining. To remove a f astener,
push on the center of the head
until it pops in. Then pull it out.
Pull the lining back. Remove the burned out bulb. To
remove the stop/taillight, back-up
or side marker light bulb, pull the
bulb straight out of its socket. To
remove the turn signal light bulb,
push it in and turn it
counterclockwise until it unlocks.
1. 2. 3.
4.
5. 6.
Lights
Maint enance
Replacing Rear Bulbs 204

Install the new bulb in the socket.
Testthelightstomakesurethe
new bulb is working.
Push the socket into the light
assembly and turn it clockwise
until it locks.
Install the trunk lining and secure
it with the fasteners. To reinstall a
f astener, reset the f astener by
pushing on the pointed end until it
pops back almost f lush with the
f ingers on the housing. Put the
f astener in the hole of the trunk
lining and push on the center until
it locks (the center is flush with
the head).
7. 8. 9.
10.
Lights
Maint enance205

Unscrew the wing bolt and take
the spare tire out of the spare tire
shelf .
Remove the three clips holding
the spare tire cover by pulling
straight up on the rings. Remove
the spare tire cover.
Loosen the f ive wheel nuts 1/2
turn with the wheel wrench.Locate the jacking point nearest
the tire you need to change. It is
pointed to by an arrow molded into
the underside of the body. Place
the jack under the jacking point.
Turn the end bracket clockwise
until the top of the jack contacts
the jacking point. Make sure the
jacking point tab is resting in the
jack notch.
4.
5. 6.7.
Changing a Flat T ire
T aking Care of t he Unexpect ed
222

Look f or any obvious coolant leaks,
such as a split radiator hose.
Everything is still extremely hot,
so use caution. If you f ind a leak, it
must be repaired bef ore you
continue driving (seeon page ). If you don’t f ind an obvious leak,
check the coolant level in the
radiator reserve tank (see page
). If the level is below the
MIN mark, add coolant to halfway
between the MIN and MAX marks. Using gloves or a large heavy
cloth, turn the radiator cap
counterclockwise, without pushing
down, to the f irst stop. This
releases any remaining pressure in
the cooling system. After the
pressure releases, push down on
the cap and turn it until it comes
off.
If there was no coolant in the
reserve tank, you may also have to
add coolant to the radiator. Let the
engine cool down until the reading
reaches the middle of the
temperature gauge, or lower,
bef ore checking the radiator.
6.
7.9.
8.
247 126
Emergency
Towing
If Your Engine Overheats
T aking Care of t he Unexpect ed
232 Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.