2002 HONDA PASSPORT recommended oil

•
* 1
* 2Under severe driving conditions, service these items more often. –These fluids: brake, clutch, P/S, battery, ATF,
Using SAE 10W-40 oil, or any viscosity other than those recommended, may reduce engin\
e life and affect the warranty. windshield washer
This service is recommended only. – Tire pressure
204 Care and Maintenance
R – Replace L – Lube I – Inspect After inspection, clean, adjust, repair or replace if necessary.Service at the interval listed x1 000 il ( k ) ft th tx 1,000 miles7.51522.53037.54552.56067.57582.59097.5105Service at the interval listed x1,000 miles (or km) or after thatnumber of months whicheverx 1,000 km1224364860728496108120132144156168number of months, whichever
comes first.months612182430364248546066727884
Engine and TransmissionAir cleaner elementRRR
Fuel tank, cap, pipes, hoses and connectionsI
Spark plugsR
•Engine oil and oil filter * 1RRRRRRRRRRRRRREngine drive beltIII
Cooling system, heater hoses, and connectionsIIIIIII•Engine coolantRRR
Timing beltR*
2
Exhaust systemIIIIIIIIIIIIII
Starter safety switchIIIIIIIIIIIIII
Auto cruise control linkage and hoseIIIIIII
Radiator core and A/C condenserI
Manual transmission oil and transfer case oilRRRRAutomatic transmissionSee page 216.
Shift-on-the-fly systemIIIIValve clearanceAdjust only if noisy.
Check oil and coolant level at each fuel stop.Inspect monthly:
Maintenance Schedule

211Care and Maintenance
Underbody — Corrosive
materials used for road-ice, snow
removal and dust control can
collect on the underbody. If these
materials are not removed,
accelerated corrosion (rust) can
occur on underbody parts such as
the fuel line, frame, floor pan and
exhaust system. At least once a
year, in the spring, flush these
materials from the underbody
with plain water.
Take care to thoroughly clean any
areas where mud and other debris
can collect. Sediment trapped in
closed areas of the frame should
be loosened before being flushed.Proper Quality Oil
Engine oils are labeled on the
containers with various API
(American Petroleum Institute)
designations of quality.
Use Only SJ Quality Oil
Additional designations of quality
may also be present, but
SJ must
be included.
The “
SJ” designation may be
shown alone, or in combination
with other designations, such as
“
SJ/CC,” “SJ/CD,” or “SJ, CC”
etc.
As long as the letters “
SJ” appear
somewhere in the designation of
oil quality indicated on the
container, the oil is of suitable
quality.
Change Interval
The oil and filter change intervals
for your engine are based on the
use of the recommended oil
quality and viscosity, as well as
high-quality filters. Using oils
other than recommended, or
extending oil change intervals
longer than those recommended,
could reduce engine life.
Your engine was filled with a
high-quality engine oil when it
left the factory. You do not have
to change this oil before the
suggested change period.
If your normal driving does not
include one or more of the “severe
driving” conditions listed below,
change the oil every 7,500 miles
(12,000 kilometers) or 6 months,
whichever comes first.
Engine Oil and Filter

213Care and Maintenance
Oil Viscosity
Engine oil viscosity (thickness) has
an effect on fuel economy. Lower
viscosity engine oils can provide
increased fuel economy; however,
higher temperature weather
conditions require higher viscosity
engine oils for satisfactory
lubrication. To get the best fuel
economy with your vehicle, you
should use a fuel-saving engine oil
of the proper viscosity. These oils
can be found in service stations andother retail stores. They are
identified by words such as
“Energy Saving,” “Conserves
Gasoline,” “Gas Saving,”
“Gasoline Saving,” “Friction
Reducing,” “Improved Gasoline
Mileage” or “Fuel Saving.”
The chart lists the recommended
engine oil viscosities for the
temperature range you expect
before the next oil change. For
temperatures above 0

F (–18
C),
SAE 10W–30 is the preferred viscosity grade. If cold-weather
starting problems are encountered
at temperatures below 0

F
(–18
C), SAE 5W–30 viscosity
oils may be required.
Oil Level Check
It is the owner ’s responsibility to
keep the engine oil at the proper
level. Check the oil level at regular
intervals (such as every other fuel
stop) and keep it above the
“minimum” level mark.
Remember, your engine may use
more oil when it is new.
The best time to check the engine
oil level is when the oil is warm,
such as during a fuel stop. Shut off
the engine and wait about 5 minutes
for the oil to drain back to the oil
pan. Pull out the dipstick, wipe it
clean, and push it back down all the
way. Now pull out the dipstick and
–20 F 0 F
– 30 C –20 C –10 C 20 F
40 F
0 C 10 C 20 C
60 F
80 F
30 C 40 C
100 F
TEMPERATURE RANGE YOU EXPECT BEFORE NEXT OIL CHANGE
VISCOSITY GRADE – AMBIENT TEMPERATURE
SAE 5W–30
SAE 10W–30, PREFERRED
SAE 15W–40, 20W–40, 20W–50

214Care and Maintenance
look at the oil level on the dipstick.
The dipstick has two markings
which indicate the minimum and
maximum allowable oil level. If the
oil level is lower than the marked
area, it indicates the need for
additional oil. Push the dipstick
back down all the way after taking
the reading.
•If you check the oil level when
the oil is cold, do not run the
engine first. The cold oil will
not drain into the pan fast
enough to give a true reading.
Engine Oil Additives
There are many extra engine oil
additives for sale. Your engine
should not need these extra
additives if you use recommended
quality engine oil and change it as
suggested. If you think your
engine has an oil-related problem,
talk to your Honda dealer.
See your Maintenance Schedule for
change intervals. If the vehicle is
operated in dusty areas it will
require more frequent element
replacement. Your Honda dealer
can be of assistance in determining
the proper replacement frequency
for the conditions under which you
operate your vehicle.
Do not attempt to clean the air
filter. The filter is designed to
provide normal filtering
efficiency between replacement
intervals.
For maximum protection, it is
advisable to use genuine Honda air
cleaner filters as replacements.
Air Cleaner Filter

217Care and Maintenance
Recommended Lubricant
Ambient
TemperatureLubricant Viscosity to Be Used
Rear
AxleFront Axle
Below 50
F(10
C)
SAE 80
or SAE80W-90
SAE
75W-90
synthetic
0
F to 90h
F(–18
C to
32
C)
SAE 90
or SAE
80W-90
SAE
75W-90
synthetic
Above 50
F(10
C)
consistentlySAE
140SAE
80W-90
or SAE
80W
-140
The engine cooling system is
designed to maintain the engine at
the proper operating temperatures.
The cooling system was filled at
the factory with a quality engine
coolant. The engine cooling system
is designed to use coolant (a
mixture of water and ethylene
glycol antifreeze) rather than plain
water. The engine coolant solution
should be used year-round. It has
many advantages such as:
•provides freezing protection as
low as –33
F (–36
C)
• provides boiling protection up
to 262
F (128
C)
•protects against rust and
corrosion in the cooling system
• maintains the proper engine
temperature for efficient
operation and emission control
•allows proper operation of the
engine coolant temperature gauge See the Maintenance Schedule in
this section to find out when the
engine coolant must be replaced.
Checking the Coolant Level
Check the engine coolant level at
the interval shown in the
Maintenance Schedule unless there
is evidence of leaking or
overheating. The engine coolant
level should be between the
maximum and the minimum level
marks on the radiator reserve tank.
Engine Cooling System

220 Care and Maintenance
If the diaphragm inside the
reservoir cap is deformed, return
it to the original (collapsed)
condition, then tighten the cap.
It is normal for the brake fluid
level to go down slightly as the
front brake pads wear. So be sure
to keep the reservoir fluid at the
proper level.
If the reservoir needs frequent
refilling, it may indicate a serious
mechanical problem.
Brake fluid absorbs water from
the air. Never use brake fluid that
has been open to the air for an
extended period. Throw it away
and use new brake fluid from a
sealed container.

Brake fluid can damage your
vehicle’s paint. Thoroughly clean
up any brake fluid spills.
Shift-on-the-Fly System
The fluid level in the system should
be checked at the intervals shown
in the Maintenance Schedule.
FILLER
PLUG
Remove the filler plug and make
sure the fluid level is up to the
edge of the hole. If it is not, add
GL-5 gear oil to bring to that
level. Use the same
GL-5 gear oil
specified for the front axle (see
page 216).
Front Wheel Bearings
Clean and repack the front wheel
bearings whenever the front brake
pads are replaced. Due to the
weight of the tire and wheel
assembly it is recommended that
they be removed from the hub
before lubricating the bearings to
prevent damage to the oil seal.
“Long Fiber” grease should not be
used to lubricate the wheel bearings.
It can cause damage. Clean the old
grease out of the bearings and hubs
before repacking.

224Care and Maintenance
Wheel Alignment
Proper wheel alignment improves
tire mileage. Your vehicle’s
suspension parts should be
inspected often and aligned when
needed (see the “Technical Data”
section). Improper alignment will
cause the front tires to roll at an
angle that will result in faster tire
wear.
Proper tire balancing provides the
best riding comfort and helps
reduce tire tread wear.
Out-of-balance tires can cause
annoying vibration and uneven
tire wear such as cupping and flat
spots.
Washing Your Vehicle
The best way to preserve your
vehicle ’s finish is to keep it clean by
frequent washings. Wash the vehicle
with lukewarm or cold water.
Do not use hot water or wash in
direct sunlight. Do not use strong
soap or chemical detergents. All
cleaning agents should be promptly
flushed from the surface and not
allowed to dry on the finish.
Polishing and Waxing
Your Vehicle
Polishing is recommended to
remove accumulated residue and
eliminate any “weathered”
appearance.
Your Honda dealer offers several
polishes and cleaners that have
proven to maintain the original
finish appearance and durability.
Protection of Exterior
Bright Metal Parts
Bright metal parts should be cleaned
regularly to keep their luster.
Washing with water is all that is
usually needed. However, chrome
polish may be used on chrome or
stainless steel trim, if necessary. A
coating of wax, rubbed to a high
polish, is recommended for all bright
metal parts.
Care of Aluminum Wheels
Aluminum wheels have a
clear-coat finish similar to paint.
Use a chamois skin, sponge or
other soft material when washing
the wheels.
Foreign Material Deposits
Calcium chloride and other salts,
ice melting agents, road oil and
tar, tree sap, bird droppings,
Exterior

263
Rear Seat, Folding94. . . . . . . . .
Rear View Mirror
105. . . . . . . . . .
Rear Window Defogger
74. . . . .
Rear Window Wiper and Washer
74. . . . . . . . . . . . .
Reclining the Seat-Backs Front
11, 91, 93. . . . . . . . . . . .
Rear
97. . . . . . . . . . . . . . . . . .
Recommended Shift Speeds
84.
Reduced Power Indicator
\b 64. . .
Replacement Information Air Cleaner Element
214. . . . .
Coolant
204, 218. . . . . . . . . . .
Engine Oil and Filter
211. . . . .
Fuses
240. . . . . . . . . . . . . . . . .
Light Bulbs
243. . . . . . . . . . . .
Schedule
204. . . . . . . . . . . . . .
Spark Plugs
235. . . . . . . . . . . . Tires
166. . . . . . . . . . . . . . . . . .
Replacing Seat Belts After a Crash
43. . . . . . . . . . . .
Reporting Safety Defects
248. . . .
Reserve Tank, Coolant
217. . . . . .
Restraint, Child
18. . . . . . . . . . .
Reverse Gear Position
77. . . . . .
Rotation, Tire
166. . . . . . . . . . . . .
Rust Protection
225. . . . . . . . . . . .
S
Safety Defects, Reporting248. . .
Safety Labels, Location of
48. . .
Safety Messages
iv. . . . . . . . . . . .
Seat Belts
4, 6. . . . . . . . . . . . . . . .


\b 
 41
\b\b\b\b\b
Maintenance42. . . . . . . . .
System Components
41
\b\b\b\b
Advice for Pregnant Women16
Cleaning229. . . . . . . . . . . . . . .
Fasten and Positio
13
\b\b\b\b\b\b\b
Lap Belt42
\b\b\b\b\b\b\b\b\b\b\b\b\
\b\b\b\b\b
Lap/Shoulder Belt41
\b\b\b\b\b\b\b\b
Reminder Light6, 41, 61. . . . .
Seats
8, 89. . . . . . . . . . . . . . . . . . .
Adjusting the
90. . . . . . . . . . .
Seat-Backs
8, 91, 92, 97
\b\b\b\b\b\b\b
Self-Adjusting Brakes162. . . . . .
Serial Number
232. . . . . . . . . . . .
Service Intervals
204, 205, 206, 207. . . . .
Service Manual
253. . . . . . . . . . .
Service Station Information
197. .
Setting the Clock
153. . . . . . . . . .
Shift Lever Position Indicator
76
Shift-on-the-Fly System220. . . . .
Fluid Capacity
239. . . . . . . . . .
Side Marker Lights Bulb Replacement
243. . . . . . . .