2002 HONDA CIVIC manual transmission

Manual Transmission
Countershaft Reassembly (cont'd)
11.Support ball bearing (A) on steel blocks (B), then
use a press (C) and an attachment (D) to press the
countershaft (E) out of the ball bearing.
lf necessary, installthe 35 mm shim selected in
step 16, then recheck the clearance,
Install the distance collar (A).35 mm shim, and new
ball bearing (B) using the specialtools and a press
(c).
46-0030r00
18.
19.
13-38
20. Tighten the new special bolt (A) (left-hand threads).
'l18 N.m (12 kgf.m,87 tbf.ftl

Manual Transmission
Synchro Ring and Gear Inspection (cont'dl
3. Inspect the thrust surface {D) on each gear hub for
wear.
Inspect the cone surface (E) on each gear hub for
wear ano rougnness.
Inspect the teeth on all gears (F) for uneven wear,
scoring, galling, and cracks.
Coat the cone surface of each gear (E) with oil, andplace its synchro ring on it. Rotate the synchro ring,
making sure that it does not slip.
13-40
\
7. Measure the clearance between each gear (A) and
its synchro ring (B) allthe way around. Hold the
synchro ring against the gear evenly while
measuring the clearance. lf the clearance is less
than the service limit, replace the synchro ring andgear.
Synchro Ring.to.Gear Clearance
Standard: 0.70 1.49 mm 10.028 0.059 in.)
Service Limit: 0.4 mm {0.016 in.)
Triple Cone Synchro-to-Gear Clearance
Slandard:
O: Outer Synchro Ring {B}to Synchro Cone (Cl
0-70 1.19 mm (0.028-0.047 in.)
@: Synchro Cone lC) to cear (A)
0.50- 1.04 mm (0.020-0.041 in.)
O: Outer Synchro Ring (B) to Gear (Al
0.95 1.68 mm 10.037 0.066 in.)
Service Limit:
O: 0.3 mm (0.012 in.)
: 0.3 mm (0.012 in.)
O; 0.6 mm 10.024 in.l
\
{

Manual Transmission
Countershaft Bearing Replacement
Special Tools Required. Adiustable bearing puller,20-40 mm 07736-A0tOOOB. Oil seal driver 07JAD-AP190100. Slide hammer, commercially available
1. Remove the bearing set plate (A)from the clutchhousing (B).
Remove the needle bearing (A) using the special
tool and a commercially available 3/8" - 16 slidehammer (B), then remove the oil guide plate C.
07736-A010008
13-42
3. Position the oil guide plate C and new needle
bearing (A) in the bore of the clutch housing (B).
Installthe needle bearing using the specialtool.
Installthe bearing set plate (A) wirh bolts (B).
B6x 1.0 nn12N.m {1.2 kgt m,8.7 tbf.ft)
(

Manual Transmission
Mainshaft Thrust Clearance Adjustment (cont'dl
72 mm Shim
Part NumberThickness
23931-P21-0000.60 mm {0.0236 in.)
B23932-P21-0000.63 mm (0.0248 in.
c23933-P21-0000.66 mm (0.0260 in.D23934-P21-0000.69 mm (0.0271 in.
E23935-P21-0000.72 mm (0.0283 in.
F23936-P21-0000.75 mm (0.0295 in.
23931-P21-0000.78 mm (0.0307 in.-23938-P2'l-0000.81 mm (0.0319 in
23939-P21-0000.84 mm (0.0331 in
J23940-P21-0000.87 mm {0.0343 in,
23941-P21-0000.90 mm (0.0354 in.
L23942.P21-0000.93 mm (0.0366 in.
M23943-P21-0000.96 mm (0.0378 in.
N239 44-P21 .0000.99 mm (0.0390 in.
o23945-P21-0001.02 mm (0.0402 in.P23946-P21-0001.05 mm (0.0413 in.
o23941-P2't-000'l.08 mm (0.0425 in
R23948-P2'l-000'1 .1 1 mm {0.0437 in
23949-P21-000'1.14 mm (0.0449 inT23950-P21-0001.17 mm {0.0461n.
U23951-P21-0001.20 mm 10.0472n.
23952-P21-0001.23 mm (0.0484n.
23953-P21-0001.26 mm {0.0496n.X23954-P21-0001.29 mm (0.0508n.
23955-P21-0001.32 mm (0.0520n.z23956-P21,0001.35 mm (0.0531 in
23957-P21-0001.38 mm (0.0543 in
AB23958-P21-0001.41 mm (0.0555nAC23959-P21-0001.44 mm (0.0567n.
AD23960-P21-0001.47 mm (0.0579n.
AE23961-P21-0001.50 mm (0.0591n.AF23962-P21-OOO1.53 mm (0.0602n.AG23963-P21-000156 mm (0.0614n.
AH23964-P21-0001.59 mm (0.0626n.
AI23965-P21-0001.62 mm (0.0638 in
AJ23966-P21-0001.65 mm (0.0650 in
AK23967-P21-0001.68 mm (0.0661 in
AL23968-P2r -0001.71 mm (0.0673 in.
AM23969-P21-0001.74 mm (0.0685 in.
AN2397 0-P21-0001.77 mm (0.0697 in.AO23971-P2't-OOO1.80 mm (0.0709 in.
13-44
12.
7. Installthe 72 mm shim (A) selected and oil guideplate M in the transmission housing (B).
,6,,-oV
Thoroughly clean the spring washer (A) and
washer (B) before installing them on the clutchhousing side ball bearing {C). Note the installation
direction of the spring washer.
8.
{
10.
11.
9.lnstallthe mainshaft in the clutch housing.
Place the transmission housing over the mainshaft
and onto the clutch housing.
Tighten the clutch and transmission housings withseveral 8 mm bolts.
NOTE: lt is not necessary to use sealing agent
between the housings.
Tap the mainshaft with a plastic hammer.

Manual Transmission
Transmission Reassembly
NOTE: Priorto reassembling, clean allthe parts in
solvent, dry them, and apply lubricant to any contact
surfaces.
1. Install the magnet (A) and differential assembly (B).
n-",-o
l;-D
Install the 28 mm spring washer (A) and 28 mm
washer (B) over the ball bearing (C). Note the
installation direction of the spring washer {A).
Apply vinyl tape to the mainshaft splines (D) toprotectthe seal. Installthe mainshaft and
countershaft (E) into the shift forks {F}. and install
them as an assembly.
13-46
\
4. Install the reverse shift fork.
6x1.0mm15 N.m (1.5 kgf.m,11 lbf.ft)
f.)
Installthe reverse idler gear (A) and reverse gear
shaft (B) by aligning the mark {C)with the reversegear shaft hole (D).
(

Manual Transmission
Transmission Reassembly (cont'dl
9. Install the 14 x 20 mm dowel pins (A).
34 N.m(3.5 kgf.m,25 rbf.ft)
Set the tapered cone ring (B) as shown. Place the
transmission housing over the clutch housing,
being careful to line up the shafts.
10.
13-48
11. Lower the transmission housing the rest of the wayas you expand the 72 mm snap ring {C). Release
the snap ring so it seats in the groove of the
countershaft bearing.
12. Check that the 52 mm snap ring is securely seatedin the groove of the countershaft bearing.
Dimension O as instalted: 3.3 6.0 mm
{0.13 0.24 in.l
Apply liquid gasket (P/N 08718-0001) to the threads
of the 32 mm sealing cap {D), and install it on thetransmission housing,
Install the transmission hangers A. and B, and the
8 mm flange bolts finger-tight.
13.
't4.
15.
8 x 1.25 mm27 N.m(2.8 kgf.m.20 rbf.ft)
(t
\A
e././
Tighten the 8 mm flange bolts in a crisscross
Pattern In several steDs.
(

Manual Transmission
Transmission Reassembly (cont'dl
22. Installthe vehicle speed sensor (VSS) {A)andO-ring (B).
22 N.m (2.2 kgf.m, r6 lbf.ft)
13-50
(
{

Frame
Frame Repair Chart
Top view
Unit:mm {in.}o: Inner diametelab1b2b3clc2c3
For sublrame o15 10.59)For engine mount e13 (0.511
For engine mount o13 (0.51)For engine mount rl3 (0.51)
For manual transmission mouot o13 {0.5'For manual transmission mount o13 10.5'For manual t.ansmission mo!nt d13 {0.51)
o
Igh
For damper mount s11.5 {0.45}For damper center o78 (3.07)
For damper mount s11.5 (0.451
For dampei mount d11.5 10.45)For subframe o15 {0.591Localing hole s25 {0.98}Locating hole e50 (1.97)
\
VEFTICALUNE
20-114