2002 HONDA ACCORD COUPE maintenance

Always change the oil and f ilter
accordingtothetimeanddistance
(miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and f ilter collect contami-
nants that can damage your engine if
they are not removed regularly.Run the engine until it reaches
normal operating temperature,
then shut it off. Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Changing the oil and f ilter requires
special tools and access f rom
underneath the car. The car should
be raised on a service station-type
hydraulic lif t f or this service. Unless
you have the knowledge and proper
equipment, you should have this
maintenance done by a skilled
mechanic.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil: it
displays the API Certif ication Seal,
and it is the proper weight as shown
on the chart. When using synthetic
oil, you must f ollow the oil and f ilter
change intervals given in the
maintenance schedule.
Your Honda does not require any oil
additives. Additives may adversely
af f ect your engine’s or transmission’s
perf ormance and durability.
1.2.
Maint enance
Engine Oil
Synthetic Oil
A dditivesChanging the Oil and Filter
250
4 4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss
W
WA
AS
SHH E
ER
R D
DR
RAA I
INN B
BOOL LTT

CONT INUED
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
1.
2.
Cooling Syst em
Maint enance
Replacing Engine Coolant
255
R RE ES
SE ER
RV V E
E T
TA
A N
NK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss 4
4-
-c
cy yl liinn d
de
err m
m o
od
de
ellss

µ
µ
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks. If the level is below the lower
mark, add f luid to bring it to the
upper mark.
Add f luid in the
dipstick tube.
Remove the f ill
plug to add f luid.
Always use Honda ATF-Z1
(Automatic Transmission Fluid). If
it is not available, you may use a
DEXRON
III automatic
transmission f luid as a temporary
replacement. However, continued
use can affect shift quality. Have
the transmission f lushed and
ref illed with Honda ATF-Z1 as
soon as it is convenient.
To thoroughly f lush the
transmission, the technician
should drain and ref ill it with
Honda ATF-Z1, then drive the
vehicle a short distance. Do this three times. Then drain and ref ill
the transmission a final time.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If you are not sure how to add f luid,
contact your Honda dealer.
5.
6.
4.
4-cylinder cars 6-cylinder cars
Maint enance
T ransmission Fluid
262
D DI
IPP S
ST TI
ICCK K
6
6- -c
cy yl liinn d
de
err m
m o
od
de
ellss U
UP
PP
PE
ER
R M
M A
AR
RKK
L
LO OW WE ER
R M
M A
AR
RKK

If Honda MTF is not available, you
may use an API service SG, SH or SJ
grade motor oil with a viscosity of
SAE 10W-30 or 10W-40 as a
temporary replacement. An SG
grade is pref erred, but an SH or SJ
grade may be used if SG is not
available. However, motor oil does
not contain the proper additives and
continued use can cause stif f er
shif ting. Replace as soon as it is
convenient.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
Check the f luid level with the
transmission at normal operating
temperature and the car sitting on
level ground. Remove the
transmission f iller bolt and caref ully
f eel inside the bolt hole with your
f inger. The f luid level should be up
to the edge of the bolt hole. If it is
not, add Honda Manual Transmis-
sion Fluid (MTF) until it starts to
run out of the hole. Reinstall the
f iller bolt and tighten it securely.
T ransmission Fluid
Maint enance
5-speed Manual Transmission
263
F FI
ILLL LEE R
R
B
BO OL LTT C
Co
or
rrreec ctt l
leev veell

Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement. However, the use of
any non-Honda brake fluid can cause
corrosion and decrease the lif e of the
system. Have the brake system
f lushed and ref illed with Honda
Heavy Duty Brake Fluid DOT 3 as
soon as possible.
Check the f luid level in the reser-
voirs monthly. There are up to two
reservoirs, depending on the model.
They are:
Brake f luid reservoir (all models)
Clutch f luid reservoir
(manual transmission only)
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected f or leaks or
worn brake pads.
The brake f luid should be replaced
according to the time recommenda-
tion in the maintenance schedule.
Brake f luid marked DOT 5 is not
compatible with your car’s braking
system and can cause extensive
damage.
Maint enance
Brake and Clutch Fluid
Brake System
264
M MA
AX
X
4
4- -c
cy yl liinn d
de
err m
m o
od
de
ellss M
MI
INN

Caref ully clean the inside of the
air cleaner housing with a damp
rag.
Remove the old air cleaner
element. Unsnap the f our hold-down clamps
and remove the air cleaner
housing cover.
To replace it: The air cleaner element is inside the
air cleaner housing on the passenger’s
side of the engine compartment.
The air cleaner element should be
cleaned or replaced according to the
time and distance recommendations
in the maintenance schedule.
Clean the air cleaner element by
blowing compressed air through it in
the opposite direction to normal air
f low. If you do not have access to
compressed air (such as a service
station), ask your Honda dealer to do
this service.
Follow the replacement procedure
for removal and reinstallation.
Reinstall the air cleaner housing
cover, snap the four hold-down
clamps back into place. Place the new air cleaner element
in the air cleaner housing.
1. 3.
4.
5.
2. Replacement
Cleaning (Severe Conditions)
4-cylinder Models
A ir Cleaner Element
Maint enance267
A A I
IRR C
CLLEE A
A N
NE ER
R E
EL
LEE M
M E
EN
NT T
H
H
O
OL LDD -
-D
D O
OW WN N C
CLLAA M
M P
PS
S

Clean up any dirt and oil around
the spark plug caps.
Remove the spark plug cap by
pulling it straight out.
Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket.
The spark plugs in your car should
be replaced according to the time
and distance recommendations in
the maintenance schedule.
Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. To lubricate
them, remove the holding clip and
pull the cover away. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Honda dealer. 1.
2.
3.
CONT INUED
Hood L atch
Spark PlugsReplacement
Hood L atch, Spark Plugs (4-cylinder Models)
Maint enance269
S SPPA
A R
RKK P
PL
LUUG G C
CAA P
P
P
P I
IVV O
OT TS
S
L
LA
A T
TC
CH H A
AS
SSSEEM
M B
BLLYY

CONT INUED
The spark plugs in your car should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Clean up any dirt and oil that have
collected around the ignition coils.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
1.
2.
3.
Maint enance
Spark Plugs (6-cylinder Models)
Replacement
271
H HO
OL LDD I
INNG G C
CLLIIPP