2002 HONDA ACCORD COUPE clock

CONT INUED
The spark plugs in your car should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Clean up any dirt and oil that have
collected around the ignition coils.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
1.
2.
3.
Maint enance
Spark Plugs (6-cylinder Models)
Replacement
271
H HO
OL LDD I
INNG G C
CLLIIPP

´
µ
Install the ignition coil. Reinstall
the hexagon socket head cap bolt.Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.Spark Plug Gap:
NGK:
DENSO:
8. 9.
10.
11.
Spark Plugs (6-cylinder Models)
Maint enance
Specif ications:
273
0.04 in (1.1 mm) PKJ16CR-L11 PZFR5F-110
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Remove the electrical connector
f rom the bulb by squeezing the
connector to unlock the tab, then
slide the connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Reinstall the radiator reserve tank. (Driver’s side) Reinstall the radiator reserve tank
and the air intake duct. (Passenger’s side) Turn on the headlights to test the
new bulb. Push the electrical connector back
onto the bulb. Make sure it is on
all the way. Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
2.
3. 4.
7. 6. 5.
6-cylinder models
4-cylinder models
Lights
Maint enance291
B BU
UL LBB
T
T A
A B
B

Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Install the new bulb in the socket.
Turn it clockwise to lock it in place. Remove the burned out bulb f rom
thesocketbypushingitinand
turning the bulb counterclockwise
until it unlocks.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
place by pushing on the center.
1.
3. 2.
4.5.
6.
7.
8.
9.
Replacing Front Turn Signal and
Side Marker L ight Bulbs
Lights
Maint enance292
H H
O
OL LDD I
INNG G C
CLLIIPP

Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Open the hood. The f ront parking
light is next to the headlight bulb. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the parking lights to
make sure the new bulb works.
(Passenger’s side)
Reinstall the radiator reserve tank.
(Driver’s side)
If you need to change a bulb on the driver’s side, remove the
radiator reserve tank.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
(Driver’s side)
Reinstall the power steering f luid
tank.
Reinstall the radiator reserve tank.
If you need to change a bulb on
the passenger’s side, remove the
radiator reserve tank. On the
driver’s side, remove the power
steering f luid tank. 2. 3.
1. 4.
5.
6.
4-cylinder models
6-cylinder models
6-cylinder models 4-cylinder models
Replacing a Parking L ight Bulb
Lights
Maint enance293
P P
O
OW WE ER
R S
STTE
EE
ER
RI INNG G F
FLLUUI IDD T
TA
A N
NK K
H
H O
OL LDD E
ER
R

Open the trunk.
Remove the fastener from the side
of the trunk lining by turning it
counterclockwise with a coin. Pull
the lining back.Determine which of the two bulbs
is burned out: stop/taillight or turn
signal/taillight.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
1.
3.
2. 4.
5.
6.
7.
8.
Replacing Rear Bulbs
(in Fenders)
Maint enance
Lights
294
F FA
A S
STTE
EN
NE ER
R

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly.
Testthelightstomakesurethe
new bulb is working.
Reinstall the plastic cover and
secure it with the screw.Use a Phillips-head screwdriver to
loosen the side marker assembly
mounting screw.
Remove the assembly f rom the
f ender by pulling out the back
edge and sliding the assembly
backwards. Remove the socket f rom the light
assembly by turning it counter-
clockwise.
Remove the bulb f rom the socket
by pulling it straight out.
Install the new bulb. Turn on the
headlights to test the bulb.
1.
2.
4.
5.
6.
7.
8.
4. 3.
Replacing a Rear Side Marker
Light Bulb
Lights
Maint enance296
S SC
CRREEW
W

Insert the socket in the assembly.
Turn it clockwise to lock it in place.
Reinstall the side marker assem-
bly in the bumper. Tighten the
mounting screw securely.Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb in the socket.Reinstall the socket. Turn it
clockwise until it locks.
Testthelightstomakesurethe
new bulb is working.
1.
2. 3.
5.
6. 4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance297