2002 GMC YUKON XL ECO mode

3-152 PROG (Program): Press this pushbutton to switch
from one side of the tape to the other.
3 NEXT: Press this pushbutton or the right SEEK arrow
to search for the next selection. A minimum
three
- second blank gap is required for the player to stop
at the beginning of the selection. The tape direction
arrow will blink while in next mode. The sound will
mute while searching for the next selection.
REV 4 (Reverse): Press this pushbutton to rapidly
reverse the tape. Press this pushbutton again to stop
reversing the tape. The radio will play the last selected
station while reversing the tape. The tape direction
arrow will blink while in reverse mode.

5 (Dolby): Press this pushbutton to reduce cassette
tape noise. The double
- D symbol will appear on the
display while the player is in this mode.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double
- D symbol are trademarks of Dolby
Laboratories Licensing Corporation. FWD 6 (Forward): Press this pushbutton to rapidly
forward the tape. Press this pushbutton again to stop
forwarding the tape. The radio will play the last selected
station while forwarding the tape. The tape direction
arrow will blink while in forward mode.
AM FM: Press this button to listen to the radio when
playing a tape or CD.
CD TAPE: Press this button to play a tape when
listening to the radio. Press this button to switch
between the tape player and CD changer if all are
loaded. When a tape is playing, a lighted arrow will
appear on the display and show the direction of play.
(If the radio is turned off, the tape stays in the player
and will resume playing at the point where it stopped.)
EJECT: Press this button to stop a tape when it is
playing or to eject a tape when it is not playing. Eject
may be activated with the radio off. Cassette tapes may
be loaded with the radio and vehicle off if this button is
pressed first.

3-18 SEEK : While listening to AM, FM1 or FM2,
press the up arrow to tune to the next station and stay
there. Press the down arrow to tune to the previous
station and stay there. The sound will mute while
seeking. If the front radio is in use, you cannot seek
through different stations.
While listening to a cassette tape, press the up arrow to
hear the next selection on the tape. Press the down arrow
to go back to the previous selection. If the cassette tape
on the front radio is in use, you cannot seek through
different selections on a tape.
While listening to a CD, press the up arrow to hear the
next track on the CD. Press the down arrow to go back
to the start of the current track (if more than eight
seconds have played). If the CD player on the front
radio is in use, you cannot seek through different tracks.
To scan preset stations, press and hold SEEK until
the radio goes into scan mode. The radio will go to a
station, play for a few seconds, then go on to the next
station. Press either SEEK arrow again to stop scanning.
If the front radio is in use, you cannot scan through
different stations. P.SET PROG (Preset Program): The front passengers
must be listening to something different for each of
these functions to work:

Press this button to scan through the preset radio
stations set on the pushbuttons on the main radio.
The radio will go to a preset station, play for a few
seconds, then go on to the next preset station.
Press this button again to stop scanning.

When a cassette tape is playing, press this button to
go to the other side of the tape.

When a CD is playing in the CD changer, press this
button to select a disc.
CD TAPE: Press this button to switch between playing
a tape and CD changer if both are loaded. Press AM FM
to return to the radio when a cassette tape or CD is
playing. The inactive tape or CD will remain safely
inside the radio for future listening.

4-47Your vehicle is provided with a button at the end of the
shift lever which when pressed enables tow/haul. When
the button is pressed, a light on the instrument panel will
illuminate to indicate that tow/haul has been selected.
Tow/haul may be turned off by pressing the button
again, at which time the indicator light on the instrument
panel will turn off. The vehicle will automatically turn
off tow/haul every time it is started.
Tow/haul is designed to be most effective when the
vehicle and trailer combined weight is at least
75 percent of the vehicle's Gross Combined Weight
Rating (GCWR). See ªWeight of the Trailerº later in
this section. Tow/haul is most useful under the following
driving conditions:

When pulling a heavy trailer or a large or heavy load
through rolling terrain.

When pulling a heavy trailer or a large or heavy load
in stop and go traffic.

When pulling a heavy trailer or a large or heavy load
in busy parking lots where improved low speed
control of the vehicle is desired. Operating the vehicle in tow/haul when lightly loaded or
with no trailer at all will not cause damage. However,
there is no benefit to the selection of tow/haul when the
vehicle is unloaded. Such a selection when unloaded
may result in unpleasant engine and transmission
driving characteristics and reduced fuel economy.
Tow/haul is recommended only when pulling a heavy
trailer or a large or heavy load.
Weight of the Trailer How heavy can a trailer safely be?
It depends on how you plan to use your rig.
For example, speed, altitude, road grades, outside
temperature and how much your vehicle is used to pull a
trailer are all important. And, it can also depend on any
special equipment that you have on your vehicle.
Use one of the following charts to determine how much
your vehicle can weigh, based upon your vehicle model
and options.

5-22 Yukon XL Denali Models
A. Bottle Jack
B. Wheel Blocks
C. Wing Nut
D. Mounting Bracket
E. Removable Tray F. Retaining Hook
G. Retaining Bracket
and Wing Nut
H. Tool Kit with Jack
Tools and Gloves Yukon Denali: The equipment you'll need is located
under the second row passenger's seat on the driver's
side of the vehicle, and behind the left trim panel on the
driver's side of the vehicle. Skip the first step and follow
the last three.
Yukon XL Denali: The equipment you'll need is
located under the storage tray in the rear trim panel on
the driver's side of the vehicle.
1. Remove the tray to access the tools.
2. There is a wing nut used to retain the tool kit.
To remove it, turn the wing nut counterclockwise.
3. To release the bottle jack from its holder, turn the
knob on the bottle jack counterclockwise to lower
the jack head.
4. The wheel blocks and the wheel block retainer can be
removed by turning the wing nut counterclockwise.
You'll use the jack handle extensions and the wheel
wrench to remove the underbody
- mounted spare tire.

5-35Yukon Denali Models (Rear Access Panel)
A. Speaker
B. Bottle Jack
C. Wing Nut D. Retaining Hook
E. Tire Blocks
F. Cover Panel 1. Put the tool kit, with the jack tools and gloves, in the
tool bag and place in the retaining bracket under the
second row passenger's seat on the driver's side of
the vehicle.
2. Tighten down with the wing nut.
3. Then, assemble tire blocks (E) and bottle jack (B)
together with the wing nut and retaining hook (D).
4. Position behind the jack storage cover in the rear
side panel on the driver's side of the vehicle just
below the speaker (A) and tighten, adjusting
clockwise until the jack is secured tight in the
mounting bracket.