2002 GMC ENVOY mirror

2-54
Automatic Dimming Feature
When turned on, an electrochromic mirror automatically
dims to the proper level to minimize glare from any
headlamps behind you after dark.
The automatic dimming feature is turned on and off by
pressing the far left button, located on the lower part of
the mirror face, for up to three seconds. A light on the
mirror will be lit when the feature is turned on. It will go
out when the feature is turned off.
Temperature Display
The temperature display is in the window in the upper
right corner of the mirror face. The display will show
the temperature in
F or
C when the compass is on.
Press the on/off button to cycle through
F,
C, or OFF.Compass Operation
Press the on/off button once to turn the compass
on or off.
There is a compass display in the window in the upper
right corner of the mirror face. The compass displays a
maximum of two characters. For example, ªNEº is
displayed for north
-east.
Compass Calibration
Press and hold the on/off button down for nine seconds
to activate the compass calibration mode. ªCALº will be
displayed in the compass window on the mirror.
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display shows ªCAL,º or

drive the vehicle on your everyday routine.
(This method may take longer to calibrate).

2-55
Compass Variance
The mirror is set to zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, such as during a long
distance cross
-country trip, it will be necessary to adjust
for compass variance. Compass variance is the
difference between earth's magnetic north and true
geographic north. If not adjusted to account for compass
variance, your compass could give false readings.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the map.
2. Press and hold the on/off button for six seconds.
Release the button when ªZONEº is displayed.
The number shown is the current zone number.
3. Scroll through the zone numbers that appear in the
compass/temperature window on the mirror by
pressing the on/off button. Once you find your zone
number, release the button. After about four seconds,
the mirror will return to the compass and
temperature display, and the new zone number will
be set.

2-56
Outside Mirrors
Adjust your outside mirrors so you can see a little of the
side of your vehicle.
Fold the mirrors in before before entering a car wash. To
do this, pull the mirrors in toward the vehicle. Push the
mirrors back out when finished.
Power Remote Control Mirrors
The control is located on the driver's door.
Turn the control to the left or right to choose the mirror;
then press the control to move the mirror in the direction
that you want the mirror to go. To secure the mirror
settings turn the knob back to the center position.

2-57
Convex Outside Mirror
A convex mirror's surface is curved so you can see more
from the driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right or left lane,
you could hit a vehicle. Check your inside
mirror or glance over your shoulder before
changing lanes.
Heated Outside Rearview Mirrors
When you operate the rear window defogger, a defogger
also warms the heated driver's and passenger's outside
rearview mirrors to help clear them of ice, snow and
condensation. See ªRear Window Defoggerº in the
Index for more information.
Electrochromic Rearview Outside Mirror
with Curb View Assist (If Equipped)
If your vehicle has this feature, the driver's outside
mirror will adjust for the glare of the headlamps behind
you. See ªElectrochromic Day/Night Rearview Mirror
with Compass and OnStar

º earlier in this section.
If your vehicle is equipped with memory mirrors, it will
also be capable of performing the curb view assist
mirror function. This feature will cause the passenger's
and/or driver's mirror to tilt to a preselected position
when the vehicle is in REVERSE (R). This feature may
be useful in allowing you to view the curb when you are
parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
short delay has occurred, the passenger's and/or driver's
mirror will return to its original position.
To change the preselected tilt position, adjust the mirrors
to the desired position while the vehicle is in
REVERSE (R). When the vehicle is shifted out of
REVERSE (R), this new position is saved in memory as
the tilt position.
This feature can be enabled/disabled through the Driver
Information Center. See ªPersonalization Featuresº in
the Index for more information.

2-63
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overload, damaging the
lighter and the heating element.
Sun Visors
To block out glare, you can pull the visor down. You can
also swing the visor from side
-to-side.
Illuminated Visor Vanity Mirror
Pull the sun visor down and lift the mirror cover to turn
on the lamps.
Accessory Inflator (If Equipped)
Your vehicle may be equipped with an air inflator
system. You can inflate things like basketballs and
bicycle tires. Also, you can use it to bring your tire
pressure up to the proper pressure. It is not designed to
inflate large objects which will require more than five
minutes to inflate, such as an air mattress.
The air inflator is located
in the rear compartment
on the passenger's side
of the vehicle behind an
access cover.
To remove the cover, pull the two tabs on the cover and
pull it off.

2-94
GM Oil Life System

Press the fuel information button until ENGINE OIL
LIFE appears in the display. The GM Oil Life System

shows an estimate of the oil's remaining useful life.
It will show 100% when the system is reset after an oil
change. It will alert you to change your oil on a schedule
consistent with your driving conditions.
Always reset the engine oil life after an oil change.
To reset the Oil Life System press and hold the select
button while ENGINE OIL LIFE is displayed.
The DIC does not replace the need to maintain your
vehicle as recommended in the Maintenance Schedule
in this manual. Also, the oil change reminder will not
detect dusty conditions or engine malfunctions that may
affect the oil. Also, the oil change reminder does not
measure how much oil you have in your engine. So, be
sure to check your oil level often. See ªEngine Oilº in
the Index.Personalization Button
You can program certain features to a preferred setting
for up to two people. Press the personalization button
to scroll through the following personalization features.
All of the personalization options may not be available
on your vehicle. Only the options available will be
displayed on your DIC.

ALARM WARNING TYPE

AUTOMATIC LOCKING

AUTOMATIC UNLOCKING

SEAT POSITION RECALL (If Equipped)

PERIMETER LIGHTING

REMOTE LOCK FEEDBACK

REMOTE UNLOCK FEEDBACK

HEADLAMPS ON AT EXIT

TILT MIRROR IN REVERSE (If Equipped)

EASY EXIT SEAT (If Equipped)

DISPLAY UNITS (E/M)

DISPLAY LANGUAGE
The driver's preferences are recalled by pressing the
unlock button on the remote keyless entry transmitter
or by pressing the appropriate memory button 1 or 2
located on the driver's door.

2-97
If you choose seat recall on remote, the memory seat
position you saved will be recalled when you unlock
the vehicle with the remote keyless entry transmitter.
Choose one of the three options and press the
personalization button while it is displayed on the DIC
to select it and move on to the next feature. For more
information on seat position recall see ªMemory Seat
and Mirrorsº in the Index.
Perimeter Lighting
Press the personalization button until PERIMETER
LIGHTING appears in the display. To select your
personalization for perimeter lighting, press the select
button while PERIMETER LIGHTING is displayed on
the DIC. Pressing the select button will scroll through
the following choices:

PERIMETER LIGHTING ON (default)

PERIMETER LIGHTING OFF
If you choose for perimeter lighting to be on, the headlamps
and back
-up lamps will come on for 40 seconds, if it is
dark enough outside, when you unlock the vehicle with
the remote keyless entry transmitter.
Choose one of the two options and press the
personalization button while it is displayed on
the DIC to select it and move on to the next feature.Remote Lock Feedback
Press the personalization button until REMOTE LOCK
FEEDBACK appears in the display. To select your
personalization for the feedback you will receive when
locking the vehicle with the remote keyless entry
transmitter, press the select button while REMOTE
LOCK FEEDBACK is displayed on the DIC.
Pressing the select button will scroll through the
following choices:

LOCK FEEDBACK: BOTH (default)

LOCK FEEDBACK: OFF

LOCK FEEDBACK: HORN

LOCK FEEDBACK: LAMPS
If you choose both, the parking lamps will flash each
time you press the button with the lock symbol on the
remote keyless entry transmitter and the horn will chirp
the second time you press the lock button.
If you choose off, there will be no feedback when
locking the vehicle.

2-99
Headlamps on at Exit
Press the personalization button until HEADLAMPS
ON AT EXIT appears in the display. To select your
personalization for how long the headlamps will stay on
when you turn off the vehicle, press the select button
while HEADLAMPS ON AT EXIT is displayed on the
DIC. Pressing the select button will scroll through the
following choices:

HEADLAMP DELAY: 10 SEC (default)

HEADLAMP DELAY: 20 SEC

HEADLAMP DELAY: 40 SEC

HEADLAMP DELAY: 60 SEC

HEADLAMP DELAY: 120 SEC

HEADLAMP DELAY: 180 SEC

HEADLAMP DELAY OFF
The amount of time you choose will be the amount of
time that the headlamps stay on after you turn off the
vehicle. If you choose off, the headlamps will turn off as
soon as you turn off the vehicle.
Choose one of the seven options and press the
personalization button while it is displayed on the DIC
to select it and move on to the next feature.Tilt Mirror in Reverse (If Equipped)
Press the personalization button until TILT MIRROR IN
REVERSE appears in the display. To select your
personalization for tilt mirror in reverse, press the select
button while TILT MIRROR IN REVERSE is displayed
on the DIC. Pressing the select button will scroll
through the following choices:

TILT MIRROR: OFF (default)

TILT MIRROR: PASSENGER

TILT MIRROR: DRIVER

TILT MIRROR: BOTH
If you choose off, neither outside mirror will be tilted
down when the vehicle is shifted into REVERSE (R).
If you choose passenger, the passenger's outside
mirror will be tilted down when the vehicle is shifted
into REVERSE (R).
If you choose driver, the driver's outside mirror
will be tilted down when the vehicle is shifted
into REVERSE (R).
If you choose both, the driver's and passenger's outside
mirror will be tilted down when the vehicle is shifted
into REVERSE (R).