2002 DODGE RAM suspension

LOOSE STEERING AND VEHICLE LEAD
CONDITION POSSIBLE CAUSE CORRECTION
EXCESSIVE PLAY IN STEERING
WHEEL1. Worn or loose suspension or
steering components.1. Inspect and repair as necessary.
2. Worn or loose wheel bearings. 2. Inspect and repair or adjust
bearings.
3. Steering gear mounting. 3. Tighten gear mounting bolts to
specification.
4. Gear out of adjustment. 4. Adjust gear to specification.
5. Worn or loose steering coupler. 5. Inspect and replace as
necessary.
VEHICLE PULLS OR LEADS TO
ONE SIDE.1. Tire Pressure. 1. Adjust tire pressure.
2. Radial tire lead. 2. Rotate tires.
3. Brakes dragging. 3. Repair as necessary.
4. Wheel alignment. 4. Align front end.
DIAGNOSIS AND TESTING - POWER STEERING
FLOW AND PRESSURE
The following procedure is used to test the opera-
tion of the power steering system on the vehicle. This
test will provide the flow rate of the power steering
pump along with the maximum relief pressure. Per-
form test any time a power steering system problem
is present. This test will determine if the power
steering pump or power steering gear is not function-
ing properly. The following pressure and flow test is
performed using Power Steering Analyzer Tool kit
6815 (Fig. 2) and Adapter Kit 6893.
POWER STEERING ANALYZER INSTALLATION
WITHOUT HYDRAULIC BOOSTER
(1) Remove the high pressure hose from the power
steering pump.
(2) Connect Tube 6844 into the pump hose fitting.
(3) Connect pressure gauge hose from the Power
Steering Analyzer to Tube 6844.
(4) Connect Adapter 6826 to Power Steering Ana-
lyzer test valve end.
(5) Connect the power steering hose from the
steering gear to Adapter 6826.
WITH HYDRAULIC BOOSTER
(1) Remove high pressure hose which goes to the
steering gear from the tube coming out of the booster.
(2) Connect Adapter 6826 to the Power Steering
Analyzer pressure gauge hose.
(3) Connect pressure gauge hose to the tube com-
ing out of the booster.
(4) Connect Tube 6844 to the steering gear hose
and Power Steering Analyzer test valve end.
FLOW AND PRESSURE TEST
(1) Check belt condition and tension.
(2) Open the test valve completely.
(3) Start engine and let idle long enough to circu-
late power steering fluid through flow/pressure test
gauge and to get air out of the fluid. Then shut off
engine.
(4) Check fluid level, add fluid as necessary. Start
engine again and let idle.
(5) Gauge should read below 1034 kPa (150 psi), if
above, inspect the hoses for restrictions and repair as
Fig. 2 Pressure Test Gauge
1 - GAUGE HOSE
2 - TUBE
3 - ADAPTER FITTINGS
4 - ANALYZER
19 - 4 STEERINGBR/BE
STEERING (Continued)

LINKAGE - 2WD
TABLE OF CONTENTS
page page
LINKAGE - 2WD
DESCRIPTION.........................40
STANDARD PROCEDURE - LUBRICATION....40
REMOVAL.............................40
INSTALLATION.........................41SPECIFICATIONS
TORQUE CHART......................41
SPECIAL TOOLS
STEERING LINKAGE...................41
LINKAGE - 2WD
DESCRIPTION
Light duty (LD) and heavy duty (HD) steering link-
age is used with IFS suspensions. The linkage is
comprised of a idler arm, pitman arm, center link
and tie rod ends. Heavy duty linkage is used on 8800
and 10500 lb. GVW vehicles.
CAUTION: If any steering components are replaced
or serviced an alignment must be performed.
NOTE: When servicing the steering linkage, use
care to avoid damaging ball stud seals. Use Puller
C-3894±A or an appropriate puller to remove tie rod
ends (Fig. 1).
STANDARD PROCEDURE - LUBRICATION
Periodic lubrication of the idler arm is required.
Refer to Lubrication And Maintenance for the recom-
mended maintenance schedule.
REMOVAL
(1) Remove the nut from the tie-rod.
(2) Remove the tie-rod end ball studs from the
steering knuckles with an appropriate puller.
(3) Remove inner tie-rod ends from center link.
(4) Remove idler arm stud from center link with
an appropriate puller. Remove the idler arm bolt
from frame bracket.
(5) Remove pitman arm ball stud from center link.
(6) Mark the pitman arm and shaft positions for
installation reference. Remove pitman arm with
Puller C-4150A (Fig. 2).
Fig. 1 Tie Rod End
1 - CLAMP
2 - ADJUSTMENT SLEEVE
3 - PULLER TOOL C-3894±A
4 - SEAL
5 - TIE-ROD END
Fig. 2 Pitman Arm
1 - PITMAN ARM
2 - SPECIAL TOOL C-4150-A
3 - WRENCH
19 - 40 LINKAGE - 2WDBR/BE

INSTALLATION
(1) Position idler arm on the frame bracket and
tighten the bolt to specification.
(2) Center steering gear to alignment marks and
install pitman arm.
(3)
Install the lock washer and retaining nut on the
pitman shaft. Tighten the nut to 251 N´m (185 ft. lbs.).
(4) Install center link to ball studs and tighten
retaining nuts to specification.
(5) Install tie-rod ends into center link and tighten
the nuts to 88 N´m (65 ft. lbs.). Install new nuts.(6) Install tie-rod ends into steering knuckles and
tighten nuts to 108 N´m (80 ft. lbs.).
(7) Remove the supports and lower the vehicle to
the surface. Center steering wheel and adjust toe,
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
NOTE: Position the clamp on the sleeve so retain-
ing bolt is located on the bottom side of the sleeve.
(8) After adjustment, tighten the tie-rod adjust-
ment sleeve clamp bolt to 61 N´m (45 ft. lbs.).
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION N´m Ft. Lbs. In. Lbs.
Pitman Arm
Gear Nut250 185 Ð
Pitman Arm
Center Link Nut11 5 8 5 Ð
Idler Arm
Mounting Bolts271 200 Ð
Idler Arm
Center Link Nut88 65 Ð
Tie Rod
Knuckle Nut108 80 Ð
Tie Rod
Center Link Nut88 65 Ð
Tie Rod
Adjuster Clamp61 45 Ð
SPECIAL TOOLS
STEERING LINKAGE
Remover Ball Stud MB-991113
Puller Tie Rod C-3894-A
Remover Pitman C-4150A
BR/BELINKAGE - 2WD 19 - 41
LINKAGE - 2WD (Continued)

(6) Mark the pitman arm and shaft positions for
installation reference. Remove the nut and washer
from the pitman arm. Remove the pitman arm with
Puller C-4150A.
INSTALLATION
(1) Align reference marks and install pitman arm.
(2) Install the lock washer and retaining nut on
the pitman shaft and tighten nut to 251 N´m (185 ft.
lbs.).
(3) Install drag link to the pitman arm. Install the
nut and tighten to 108 N´m (80 ft. lbs.).
(4) Install drag link to the right steering knuckle.
Install the nut and tighten to 88 N´m (65 ft. lbs.).
(5) Install tie rod to the left steering knuckle and
drag link. Install the nuts and tighten to 108 N´m
(80 ft. lbs.).(6) Install steering damper on the axle. Tighten
nut to 95 N´m (75 ft. lbs.).
(7) Install steering damper on the tie rod. Tighten
nut to 81 N´m (60 ft. lbs.).
(8) Remove the supports and lower the vehicle to
the surface. Center steering wheel and adjust toe,
refer to Group 2 Suspension.
(9) After adjustment tighten tie rod adjustment
sleeve clamp bolts to 61 N´m (45 ft. lbs.).
NOTE: Position the clamp on the sleeve so retain-
ing bolt is located on the bottom side of the sleeve.
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION N´m Ft. Lbs. In. Lbs.
Pitman Arm
Gear Shaft251 185 Ð
Drag Link
Pitman Arm108 80 Ð
Drag Link
Tie Rod88 65 Ð
Drag Link
Adjuster Clamp61 45 Ð
Tie Rod End
Knuckle108 80 Ð
Tie Rod End
Adjuster Clamp61 45 Ð
Steering Damper
Axle95 70 Ð
Steering Damper
Tie Rod81 60 Ð
BR/BELINKAGE - 4WD 19 - 43
LINKAGE - 4WD (Continued)

AIR LEAK VACUUM TEST - DIAGNOSIS
AND TESTING, FUEL SYSTEM...........14-57
AIR PUMP FILTER - INSTALLATION......25-30
AIR PUMP FILTER - REMOVAL..........25-30
AIR TESTING TRANSMISSION CLUTCH
AND BAND OPERATION - DIAGNOSIS
AND TESTING................21-100,21-272
AIR TO OIL COOLER - INSTALLATION.....7-87
AIR TO OIL COOLER - REMOVAL.........7-86
AIRBAG - ASSEMBLY, DRIVER..........8O-16
AIRBAG - DESCRIPTION, DRIVER........8O-14
AIRBAG - DESCRIPTION, PASSENGER....8O-21
AIRBAG - DISASSEMBLY, DRIVER.......8O-15
AIRBAG - INSTALLATION, DRIVER.......8O-17
AIRBAG - INSTALLATION, PASSENGER . . . 8O-23
AIRBAG - OPERATION, DRIVER.........8O-14
AIRBAG - OPERATION, PASSENGER......8O-21
AIRBAG - REMOVAL, DRIVER...........8O-14
AIRBAG - REMOVAL, PASSENGER.......8O-21
AIRBAG CONTROL MODULE -
DESCRIPTION........................8O-6
AIRBAG CONTROL MODULE -
INSTALLATION.......................8O-8
AIRBAG CONTROL MODULE -
OPERATION..........................8O-6
AIRBAG CONTROL MODULE - REMOVAL . . . 8O-7
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-4
AIRBAG INDICATOR - DESCRIPTION.......8J-15
AIRBAG INDICATOR - OPERATION.......8J-15
AIRBAG ON/OFF SWITCH -
DESCRIPTION, PASSENGER............8O-23
AIRBAG ON/OFF SWITCH -
INSTALLATION, PASSENGER...........8O-25
AIRBAG ON/OFF SWITCH - OPERATION,
PASSENGER........................8O-24
AIRBAG ON/OFF SWITCH - REMOVAL,
PASSENGER........................8O-24
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-4
AIRBAG SYSTEM - SPECIAL TOOLS.......8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED.............8O-4
AIRFLOW - DESCRIPTION, HVAC
SYSTEM............................24-30
AJAR SWITCH - DESCRIPTION, DOOR....8L-34
AJAR SWITCH - DIAGNOSIS AND
TESTING, DOOR.....................8L-34
AJAR SWITCH - INSTALLATION, DOOR . . . 8L-35
AJAR SWITCH - REMOVAL, DOOR.......8L-35
ALIGNMENT - DESCRIPTION, WHEEL.......2-1
ALIGNMENT - OPERATION, WHEEL........2-2
ALIGNMENT I.F.S. - STANDARD
PROCEDURES.........................2-3
ALIGNMENT LINK/COIL SUSPENSION -
STANDARD PROCEDURE.................2-5
ALIGNMENT, SPECIAL TOOLS -
HEADLAMP..........................8L-4
ALIGNMENT, SPECIFICATIONS............2-6
ALUMINUM THREAD REPAIR -
STANDARD PROCEDURE........21-114,21-286
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-12
AMBIENT TEMP SENSOR -
INSTALLATION......................8M-13
AMBIENT TEMP SENSOR - OPERATION . . 8M-12
AMBIENT TEMP SENSOR - REMOVAL
....8M-12
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING
.............8M-12
AMPERAGE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP
.................14-10
ANTENNA - DIAGNOSIS AND TESTING
.....8A-5
ANTENNA BODY & CABLE -
DESCRIPTION
........................8A-4
ANTENNA BODY & CABLE -
INSTALLATION
.......................8A-6
ANTENNA BODY & CABLE - OPERATION
. . . 8A-4
ANTENNA BODY & CABLE - REMOVAL
.....8A-6
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL
..................8A-9
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL
..................8A-9
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
.......................8E-11
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
.......................8E-12
ANTILOCK BRAKE - OPERATION,
CONTROLLER
.......................8E-11ANTILOCK BRAKE - REMOVAL,
CONTROLLER.......................8E-11
ANTILOCK BRAKES - DIAGNOSIS AND
TESTING............................5-36
A-PILLAR GRAB HANDLE -
INSTALLATION......................23-119
A-PILLAR GRAB HANDLE - REMOVAL . . . 23-119
A-PILLAR TRIM - INSTALLATION.......23-119
A-PILLAR TRIM - REMOVAL...........23-119
A-PILLAR TWEETER SPEAKER -
INSTALLATION.......................8A-19
A-PILLAR TWEETER SPEAKER -
REMOVAL..........................8A-18
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-7
APPLIQUE - INSTALLATION........23-63,23-68
APPLIQUE - REMOVAL...........23-63,23-68
ARM / ADJUSTER ASSEMBLY -
INSTALLATION, ROCKER................9-26
ARM / ADJUSTER ASSEMBLY -
REMOVAL, ROCKER...................9-26
ARM / ADJUSTER ASSY - CLEANING,
ROCKER............................9-146
ARM / ADJUSTER ASSY - DESCRIPTION,
ROCKER............................9-145
ARM / ADJUSTER ASSY - INSPECTION,
ROCKER............................9-146
ARM / ADJUSTER ASSY -
INSTALLATION, ROCKER...........9-148,9-84
ARM / ADJUSTER ASSY - REMOVAL,
ROCKER.......................9-145,9-84
ARM - DESCRIPTION, WIPER............8R-11
ARM - INSTALLATION, LOWER
CONTROL.......................2-10,2-20
ARM - INSTALLATION, UPPER
CONTROL.......................2-13,2-19
ARM - INSTALLATION, WIPER..........8R-12
ARM - OPERATION, WIPER............8R-11
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-20
ARM - REMOVAL, UPPER CONTROL . . 2-13,2-19
ARM - REMOVAL, WIPER..............8R-12
ARMREST/CONSOLE - INSTALLATION,
CENTER SEAT......................23-132
ARMREST/CONSOLE - REMOVAL,
CENTER SEAT......................23-132
ARMREST/LATCH COVER -
INSTALLATION, CENTER SEAT.........23-132
ARMREST/LATCH COVER - REMOVAL,
CENTER SEAT......................23-132
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-4
ASD SENSE - PCM INPUT - OPERATION....8I-4
ASH RECEIVER - INSTALLATION........23-107
ASH RECEIVER - REMOVAL...........23-107
ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL.................23-117
ASSEMBLY - INSTALLATION, ROCKER
ARM / ADJUSTER.....................9-26
ASSEMBLY - OVERHEAD CONSOLE
ASSEMBLY..........................8M-8
ASSEMBLY - REMOVAL, INSTRUMENT
PANEL............................23-115
ASSEMBLY - REMOVAL, ROCKER ARM /
ADJUSTER...........................9-26
ASSEMBLY, ASSEMBLY - OVERHEAD
CONSOLE...........................8M-8
ASSEMBLY, AXLE VACUUM MOTOR.......3-34
ASSEMBLY, DIAGNOSIS AND
TESTING....................21-122,21-294
ASSEMBLY, DIFFERENTIAL . 3-126,3-38,3-66,3-97
ASSEMBLY, DIFFERENTIAL - POWR-LOK . . . 3-99
ASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-129,3-70
ASSEMBLY, DOUBLE CARDAN
UNIVERSAL JOINTS
...................3-11
ASSEMBLY, DRIVER AIRBAG
...........8O-16
ASSEMBLY, FLYWHEEL
.................6-14
ASSEMBLY, FRONT CLUTCH
.....21-162,21-333
ASSEMBLY, FRONT SERVO
......21-164,21-335
ASSEMBLY, GLOVE BOX
..............23-111
ASSEMBLY, HVAC HOUSING
............24-36
ASSEMBLY, INSTRUMENT CLUSTER
......8J-12
ASSEMBLY, MANUAL - NV4500
.........21-21
ASSEMBLY, MANUAL - NV5600
.........21-64
ASSEMBLY, OIL PUMP
.................9-49
ASSEMBLY, OIL PUMP
.........21-169,21-340
ASSEMBLY, OVERDRIVE UNIT
....21-180,21-354ASSEMBLY, OVERRUNNING CLUTCH
CAM/OVERDRIVE PISTON
RETAINER...................21-193,21-364
ASSEMBLY, PLANETARY GEARTRAIN/
OUTPUT SHAFT...............21-199,21-371
ASSEMBLY, REAR CLUTCH......21-205,21-377
ASSEMBLY, REAR SERVO.......21-207,21-379
ASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-9
ASSEMBLY, TRANSFER CASE - NV241HD . 21-480
ASSEMBLY, TRANSFER CASE - NV241LD . 21-445
ASSEMBLY, VALVE BODY.......21-248,21-420
ASSIST HANDLE - INSTALLATION.......23-124
ASSIST HANDLE - REMOVAL..........23-124
ASSY - CLEANING, ROCKER ARM /
ADJUSTER..........................9-146
ASSY - DESCRIPTION, ROCKER ARM /
ADJUSTER..........................9-145
ASSY - INSPECTION, ROCKER ARM /
ADJUSTER..........................9-146
ASSY - INSTALLATION, ROCKER ARM /
ADJUSTER......................9-148,9-84
ASSY - REMOVAL, ROCKER ARM /
ADJUSTER......................9-145,9-84
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-2
AUDIO SYSTEMS, SPECIAL TOOLS.......8A-4
AUTO. TRANS. - INSTALLATION, DIESEL
WITH..........................8P-12,8P-6
AUTO. TRANS. - REMOVAL, DIESEL
WITH...........................8P-5,8P-9
AUTOMATIC DAY / NIGHT MIRROR -
DESCRIPTION.......................8N-11
AUTOMATIC DAY / NIGHT MIRROR -
INSTALLATION......................8N-13
AUTOMATIC DAY / NIGHT MIRROR -
OPERATION.........................8N-12
AUTOMATIC DAY / NIGHT MIRROR -
REMOVAL..........................8N-13
AUTOMATIC DAY/NIGHT MIRROR -
DIAGNOSIS AND TESTING.............8N-12
AUTOMATIC TRANSMISSION - 46RE -
DESCRIPTION.......................21-89
AUTOMATIC TRANSMISSION - 46RE -
OPERATION.........................21-91
AUTOMATIC TRANSMISSION - 47RE -
DESCRIPTION......................21-261
AUTOMATIC TRANSMISSION - 47RE -
OPERATION........................21-263
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING.......21-268,21-96
AUTOMATIC TRANSMISSION FLUID -
DESCRIPTION.........................0-6
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-6
AXLE - 248FBI - ADJUSTMENTS, FRONT . . . 3-19
AXLE - 248FBI - DESCRIPTION, FRONT....3-14
AXLE - 248FBI - INSTALLATION, FRONT....3-18
AXLE - 248FBI - OPERATION, FRONT......3-14
AXLE - 248FBI - REMOVAL, FRONT.......3-18
AXLE - 248RBI - ADJUSTMENTS, REAR....3-51
AXLE - 248RBI - DESCRIPTION, REAR.....3-46
AXLE - 248RBI - INSTALLATION, REAR....3-51
AXLE - 248RBI - OPERATION, REAR.......3-46
AXLE - 248RBI - REMOVAL, REAR........3-51
AXLE - 267RBI - ADJUSTMENTS, REAR....3-83
AXLE - 267RBI - DESCRIPTION, REAR.....3-78
AXLE - 267RBI - INSTALLATION, REAR....3-82
AXLE - 267RBI - OPERATION, REAR.......3-78
AXLE - 267RBI - REMOVAL, REAR........3-82
AXLE - 286RBI - ADJUSTMENTS, REAR . . . 3-112
AXLE - 286RBI - DESCRIPTION, REAR....3-107
AXLE - 286RBI - INSTALLATION, REAR . . . 3-112
AXLE - 286RBI - OPERATION, REAR......3-108
AXLE - 286RBI - REMOVAL, REAR.......3-112
AXLE - DIAGNOSIS AND
TESTING...............3-108,3-15,3-47,3-80
AXLE - INSTALLATION, DANA 44.....2-20,2-21
AXLE - INSTALLATION, DANA 60.....2-20,2-22
AXLE - INSTALLATION, INTERMEDIATE....3-30
AXLE - REMOVAL, DANA 44.............2-21
AXLE - REMOVAL, DANA 60.............2-21
AXLE, 248FBI - FRONT
.................3-27
AXLE, 248RBI - REAR
..................3-59
AXLE, 267RBI - REAR
..................3-91
AXLE, 286 RBI - REAR
................3-120
AXLE, 286RBI - REAR
.................3-120
2 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-58,7-60,7-62
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT............21-157,21-327
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-6
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE........21-158,21-329
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING................21-157,21-327
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-15
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE.......................21-460
FLUID DRAIN/REFILL - STANDARD
PROCEDURE.......................21-497
FLUID INDICATOR - DESCRIPTION,
WASHER...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER...................8J-35
FLUID INDICATOR - OPERATION,
WASHER...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING.........21-101,21-273
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT.....21-157,
21-327
FLUID LEVEL - STANDARD PROCEDURE,
BRAKE...............................5-15
FLUID LEVEL CHECK - STANDARD
PROCEDURE.................21-157,21-328
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-17
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-78,7-82,7-84
FLUSHING COOLERS AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-79,7-82,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-34
FLYWHEEL - ASSEMBLY................6-14
FLYWHEEL - DIAGNOSIS AND TESTING....6-13
FLYWHEEL - DISASSEMBLY.............6-13
FOG LAMP - DIAGNOSIS AND TESTING . . . 8L-10
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-13
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-12
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-69
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . 9-10,9-122,
9-66
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-8
FRAME SERVICE, DESCRIPTION..........13-7
FRONT - 2500 - INSTALLATION..........5-23
FRONT - 2500 - REMOVAL
..............5-22
FRONT - 3500 - INSTALLATION
..........5-23
FRONT - 3500 - REMOVAL
..............5-22
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL
............................9-32
FRONT - INSTALLATION
............5-14,5-26FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-160,9-32
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-7
FRONT - OPERATION, CRANKSHAFT OIL
SEAL...............................9-32
FRONT - REMOVAL................5-11,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-160,9-32
FRONT - REMOVAL, PROPELLER SHAFT....3-6
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-2
FRONT AXLE - 248FBI - ADJUSTMENTS....3-19
FRONT AXLE - 248FBI - DESCRIPTION.....3-14
FRONT AXLE - 248FBI - INSTALLATION....3-18
FRONT AXLE - 248FBI - OPERATION......3-14
FRONT AXLE - 248FBI - REMOVAL........3-18
FRONT AXLE, 248FBI..................3-27
FRONT AXLE, SPECIAL TOOLS...........3-27
FRONT BEARING - INSTALLATION,
OUTPUT SHAFT...............21-171,21-342
FRONT BEARING - REMOVAL, OUTPUT
SHAFT......................21-171,21-342
FRONT BUMPER - INSTALLATION.........13-4
FRONT BUMPER - REMOVAL............13-4
FRONT BUMPER - SPORT -
INSTALLATION........................13-5
FRONT BUMPER - SPORT - REMOVAL......13-5
FRONT CLUTCH - ASSEMBLY....21-162,21-333
FRONT CLUTCH - DESCRIPTION . . 21-160,21-330
FRONT CLUTCH - DISASSEMBLY . 21-161,21-331
FRONT CLUTCH - INSPECTION . . . 21-162,21-332
FRONT CLUTCH - OPERATION . . . 21-160,21-330
FRONT COVER INSTALLED -
INSTALLATION, FRONT OIL SEAL.........9-89
FRONT COVER INSTALLED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT COVER REMOVED -
INSTALLATION, FRONT OIL SEAL.........9-90
FRONT COVER REMOVED - REMOVAL,
FRONT OIL SEAL......................9-89
FRONT DOOR FORE/AFT - ADJUSTMENT . . 23-69
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL...........23-152
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR IN/OUT - ADJUSTMENT....23-70
FRONT DOOR LATCH - ADJUSTMENT.....23-73
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION.......23-153
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL...........23-153
FRONT DOOR SECOND WEATHERSTRIP -
INSTALLATION......................23-154
FRONT DOOR SECOND WEATHERSTRIP -
REMOVAL.........................23-154
FRONT DOOR SPEAKER - INSTALLATION . . 8A-19
FRONT DOOR SPEAKER - REMOVAL.....8A-19
FRONT DOOR UP/DOWN - ADJUSTMENT . . 23-70
FRONT DOOR UPPER CORNER SEAL -
INSTALLATION......................23-154
FRONT DOOR UPPER CORNER SEAL -
REMOVAL.........................23-153
FRONT END SPLASH SHIELDS -
INSTALLATION.......................23-92
FRONT END SPLASH SHIELDS -
REMOVAL..........................23-92
FRONT FASCIA - INSTALLATION
..........13-2
FRONT FASCIA - REMOVAL
..............13-2
FRONT FASCIA - SPORT - INSTALLATION
. . 13-3
FRONT FASCIA - SPORT - REMOVAL
......13-3
FRONT FENDER - INSTALLATION, LEFT
. . . 23-93
FRONT FENDER - INSTALLATION, RIGHT
. . 23-94
FRONT FENDER - REMOVAL, LEFT
.......23-93
FRONT FENDER - REMOVAL, RIGHT
......23-94
FRONT LOWER FASCIA - INSTALLATION
. . . 13-3
FRONT LOWER FASCIA - REMOVAL
.......13-3
FRONT MOUNT - INSTALLATION
....9-174,9-42,
9-98
FRONT MOUNT - REMOVAL
....9-173,9-41,9-97
FRONT OIL SEAL - FRONT COVER
INSTALLED - INSTALLATION
.............9-89FRONT OIL SEAL - FRONT COVER
INSTALLED - REMOVAL................9-89
FRONT OIL SEAL - FRONT COVER
REMOVED - INSTALLATION..............9-90
FRONT OIL SEAL - FRONT COVER
REMOVED - REMOVAL.................9-89
FRONT OUTPUT SHAFT SEAL -
INSTALLATION................21-461,21-498
FRONT OUTPUT SHAFT SEAL -
REMOVAL...................21-461,21-498
FRONT PARKING BRAKE CABLE -
INSTALLATION........................5-30
FRONT PARKING BRAKE CABLE -
REMOVAL...........................5-29
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-20
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-20
FRONT SERVO - ASSEMBLY.....21-164,21-335
FRONT SERVO - CLEANING.....21-164,21-334
FRONT SERVO - DESCRIPTION . . . 21-164,21-334
FRONT SERVO - DISASSEMBLY . . 21-164,21-334
FRONT SERVO - INSPECTION....21-164,21-335
FRONT SERVO - OPERATION....21-164,21-334
FRONT SUSPENSION, SPECIAL TOOLS -
INDEPENDENT.........................2-9
FRONT TOW HOOK - INSTALLATION......13-10
FRONT TOW HOOK - REMOVAL.........13-10
FRONT WHEEL SPEED SENSOR -
DESCRIPTION........................5-38
FRONT WHEEL SPEED SENSOR -
OPERATION...........................5-38
FUEL DELIVERY - SPECIFICATIONS,
TORQUE............................14-4
FUEL DELIVERY SYSTEM -
DESCRIPTION........................14-2
FUEL DELIVERY SYSTEM -
DESCRIPTION, DIESEL................14-55
FUEL DELIVERY SYSTEM - OPERATION....14-2
FUEL DRAIN MANIFOLD - DESCRIPTION . . 14-89
FUEL DRAIN MANIFOLD - INSTALLATION . . 14-90
FUEL DRAIN MANIFOLD - OPERATION....14-89
FUEL DRAIN MANIFOLD - REMOVAL.....14-90
FUEL FILL DOOR - INSTALLATION.......23-95
FUEL FILL DOOR - REMOVAL...........23-95
FUEL FILLER CAP - DESCRIPTION.......25-34
FUEL FILLER CAP - OPERATION.........25-34
FUEL FILLER CAP - REMOVAL/
INSTALLATION.......................25-34
FUEL FILTER - STANDARD
PROCEDURES, WATER DRAINING AT.....14-61
FUEL FILTER / WATER SEPARATOR -
DESCRIPTION.......................14-63
FUEL FILTER / WATER SEPARATOR -
INSTALLATION.......................14-65
FUEL FILTER / WATER SEPARATOR -
OPERATION.........................14-63
FUEL FILTER / WATER SEPARATOR -
REMOVAL..........................14-64
FUEL FILTER/PRESSURE REGULATOR -
DESCRIPTION........................14-5
FUEL FILTER/PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL FILTER/PRESSURE REGULATOR -
OPERATION..........................14-5
FUEL FILTER/PRESSURE REGULATOR -
REMOVAL...........................14-5
FUEL GAUGE - DESCRIPTION...........8J-19
FUEL GAUGE - OPERATION.............8J-20
FUEL GAUGE SENDING UNIT -
DIAGNOSIS AND TESTING..............14-7
FUEL HEATER - DESCRIPTION
..........14-66
FUEL HEATER - DIAGNOSIS AND
TESTING
...........................14-66
FUEL HEATER - OPERATION
............14-66
FUEL HEATER - REMOVAL/INSTALLATION
. 14-67
FUEL HEATER RELAY - DESCRIPTION
....14-67
FUEL HEATER RELAY - DIAGNOSIS AND
TESTING
...........................14-68
FUEL HEATER RELAY - INSTALLATION
....14-69
FUEL HEATER RELAY - OPERATION
......14-67
FUEL HEATER RELAY - REMOVAL
........14-69
FUEL INDICATOR - DESCRIPTION, LOW
. . . 8J-22
FUEL INDICATOR - OPERATION, LOW
.....8J-22
FUEL INJECTION - SPECIFICATIONS,
TORQUE - GAS
......................14-35
FUEL INJECTION PUMP DATA PLATE,
SPECIFICATIONS
.....................14-77
BR/BEINDEX 13
Description Group-Page Description Group-Page Description Group-Page

HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER....................8L-6
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER................8L-6
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER....................8L-6
HIGH PRESSURE FUEL LINES -
DESCRIPTION.......................14-78
HIGH PRESSURE FUEL LINES -
OPERATION.........................14-78
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION.......................24-46
HIGH PRESSURE RELIEF VALVE -
OPERATION.........................24-47
HIGH PRESSURE SWITCH -
DESCRIPTION, A/C...................24-20
HIGH PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-20
HIGH PRESSURE SWITCH -
INSTALLATION, A/C...................24-20
HIGH PRESSURE SWITCH - OPERATION,
A/C................................24-20
HIGH PRESSURE SWITCH - REMOVAL,
A/C................................24-20
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-7
HIGH-PRESSURE FUEL LINE LEAKS -
DIAGNOSIS AND TESTING.............14-78
HINGE - INSTALLATION.....23-100,23-72,23-80
HINGE - REMOVAL........23-100,23-72,23-79
HITCH - INSTALLATION, TRAILER.........13-11
HITCH - REMOVAL, TRAILER...........13-11
HOISTING - STANDARD PROCEDURE.......0-9
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-17
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-18
HOLDDOWN - OPERATION, BATTERY.....8F-17
HOLDDOWN - REMOVAL, BATTERY......8F-17
HOLDER - INSTALLATION, CUP........23-110
HOLDER - REMOVAL, CUP............23-109
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-9
HONING - STANDARD PROCEDURE,
CYLINDER BORE..................9-11,9-65
HOOD - INSTALLATION...............23-101
HOOD - REMOVAL...................23-101
HOOK - INSTALLATION, COAT..........23-125
HOOK - INSTALLATION, FRONT TOW.....13-10
HOOK - REMOVAL, COAT.............23-124
HOOK - REMOVAL, FRONT TOW.........13-10
HORN - DESCRIPTION.............8H-1,8H-2
HORN - DIAGNOSIS AND TESTING.......8H-2
HORN - INSTALLATION.................8H-3
HORN - OPERATION...............8H-1,8H-2
HORN - REMOVAL....................8H-2
HORN RELAY - DESCRIPTION.......8W-97-12
HORN RELAY - DESCRIPTION...........8H-3
HORN RELAY - DIAGNOSIS AND
TESTING........................8W-97-12
HORN RELAY - DIAGNOSIS AND
TESTING............................8H-3
HORN RELAY - INSTALLATION.......8W-97-12
HORN RELAY - INSTALLATION...........8H-4
HORN RELAY - OPERATION.............8H-3
HORN RELAY - REMOVAL..........8W-97-12
HORN RELAY - REMOVAL..............8H-4
HORN SWITCH - DESCRIPTION..........8H-4
HORN SWITCH - DIAGNOSIS AND
TESTING............................8H-5
HORN SWITCH - OPERATION............8H-5
HORN SWITCH - REMOVAL.............8H-5
HOSE CLAMPS - DESCRIPTION...........7-4
HOSE CLAMPS - OPERATION.............7-4
HOSE WITH AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-76
HOSE WITH AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-73
HOSE WITHOUT AIR CONDITIONING -
INSTALLATION, WATER PUMP BYPASS....7-77
HOSE WITHOUT AIR CONDITIONING -
REMOVAL, WATER PUMP BYPASS........7-76
HOSES - PRESSURE - DESCRIPTION
.....19-39
HOSES - PRESSURE - OPERATION
.......19-39
HOSES - RETURN - DESCRIPTION
.......19-39
HOSES - RETURN - OPERATION
.........19-39
HOSES/LINES/TUBES PRECAUTIONS -
CAUTION, REFRIGERANT
..............24-43HOSES/TUBES - DESCRIPTION, WASHER . . 8R-8
HOSES/TUBES - OPERATION, WASHER....8R-8
HOUSING - ASSEMBLY, HVAC...........24-36
HOUSING - DIAGNOSIS AND TESTING,
CLUTCH..............................6-9
HOUSING - DISASSEMBLY, HVAC........24-35
HOUSING - INSTALLATION, CLUTCH......6-11
HOUSING - INSTALLATION, GEAR........9-188
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - REMOVAL, CLUTCH..........6-11
HOUSING - REMOVAL, GEAR...........9-187
HOUSING - REMOVAL, HVAC...........24-34
HOUSING BUSHING - INSTALLATION,
EXTENSION..................21-156,21-326
HOUSING BUSHING - REMOVAL,
EXTENSION..................21-156,21-326
HOUSING BUSHING AND SEAL -
INSTALLATION, EXTENSION.....21-460,21-497
HOUSING BUSHING AND SEAL -
REMOVAL, EXTENSION.........21-460,21-497
HOUSING COVER - INSTALLATION, GEAR . 9-190
HOUSING COVER - REMOVAL, GEAR.....9-189
HOUSING FLUID LEAK - DIAGNOSIS AND
TESTING, CONVERTER.........21-101,21-273
HOUSING INLET BAFFLE -
INSTALLATION, HVAC.................24-36
HOUSING INLET BAFFLE - REMOVAL,
HVAC..............................24-35
HOUSING PLUG - INSTALLATION,
STEERING GEAR.......................19-30
HOUSING PLUG - REMOVAL, STEERING
GEAR..............................19-29
HOUSING SEAL - INSTALLATION,
EXTENSION..................21-156,21-327
HOUSING SEAL - NV4500 -
INSTALLATION, ADAPTER..............21-42
HOUSING SEAL - NV4500 -
INSTALLATION, EXTENSION............21-42
HOUSING SEAL - NV4500 - REMOVAL,
ADAPTER...........................21-42
HOUSING SEAL - NV4500 - REMOVAL,
EXTENSION.........................21-42
HOUSING SEAL - NV5600 -
INSTALLATION, ADAPTER..............21-85
HOUSING SEAL - NV5600 -
INSTALLATION, EXTENSION............21-85
HOUSING SEAL - NV5600 - REMOVAL,
ADAPTER...........................21-85
HOUSING SEAL - NV5600 - REMOVAL,
EXTENSION.........................21-85
HOUSING SEAL - REMOVAL,
EXTENSION..................21-156,21-326
HUB / BEARING - INSTALLATION......2-17,2-9
HUB / BEARING - REMOVAL..........2-16,2-9
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-35
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
HVAC HOUSING INLET BAFFLE -
INSTALLATION.......................24-36
HVAC HOUSING INLET BAFFLE -
REMOVAL..........................24-35
HVAC SYSTEM AIRFLOW - DESCRIPTION . 24-30
HYDRAULIC BOOSTER - DIAGNOSIS
AND TESTING........................5-18
HYDRAULIC LIFTERS - CLEANING
....9-37,9-92
HYDRAULIC LIFTERS - INSTALLATION
. 9-37,9-92
HYDRAULIC LIFTERS - REMOVAL
....9-37,9-92
HYDRAULIC PRESSURE TEST -
DIAGNOSIS AND TESTING
.......21-270,21-98
HYDRAULIC SCHEMATICS, SCHEMATICS
AND DIAGRAMS
..............21-132,21-302
HYDRAULIC TAPPETS - DIAGNOSIS AND
TESTING
........................9-36,9-91
HYDRAULIC/MECHANICAL -
DESCRIPTION
.........................5-4
HYDRAULIC/MECHANICAL - WARNING
.....5-4
HYDROMETER TEST - STANDARD
PROCEDURE
........................8F-11
HYDROSTATIC LOCK - STANDARD
PROCEDURE
................9-11,9-122,9-66
IDENTIFICATION - DESCRIPTION,
FASTENER
.........................Intro.-6
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION
.............8W-01-6
IDENTIFICATION LAMP - INSTALLATION,
OUTBOARD
.........................8L-29IDENTIFICATION LAMP - REMOVAL,
OUTBOARD.........................8L-28
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IDENTIFICATION PLATE - DESCRIPTION,
EQUIPMENT.......................Intro.-3
IDLE AIR CONTROL MOTOR -
DESCRIPTION.......................14-40
IDLE AIR CONTROL MOTOR -
OPERATION.........................14-40
IGNITION - SPECIFICATIONS, TORQUE.....8I-2
IGNITION CIRCUIT SENSE -
DESCRIPTION.......................8E-17
IGNITION CIRCUIT SENSE - OPERATION . . 8E-19
IGNITION COIL RESISTANCE, 5.9L
ENGINES............................8I-3
IGNITION COIL RESISTANCE, 8.0L V-10
ENGINE..............................8I-4
IGNITION SWITCH - DESCRIPTION.......19-11
IGNITION SWITCH - DESCRIPTION,
KEY-IN..............................19-9
IGNITION SWITCH - DIAGNOSIS AND
TESTING...........................19-11
IGNITION SWITCH - INSTALLATION......19-12
IGNITION SWITCH - OPERATION........19-11
IGNITION SWITCH - REMOVAL..........19-12
IGNITION SWITCH AND KEY LOCK
CYLINDER - DIAGNOSIS AND TESTING....19-9
IGNITION TIMING, SPECIFICATIONS.......8I-4
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-13
INDEPENDENT FRONT SUSPENSION,
SPECIAL TOOLS.......................2-9
INDICATOR - DESCRIPTION, ABS........8J-14
INDICATOR - DESCRIPTION, AIRBAG.....8J-15
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-15
INDICATOR - DESCRIPTION, CHECK
GAUGES............................8J-17
INDICATOR - DESCRIPTION, CRUISE.....8J-18
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-20
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-21
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-22
INDICATOR - DESCRIPTION, OVERDRIVE
OFF ...............................8J-26
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-27
INDICATOR - DESCRIPTION, SERVICE
REMINDER..........................8J-27
INDICATOR - DESCRIPTION, TRANS
OVERTEMP.........................8J-31
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-32
INDICATOR - DESCRIPTION, UPSHIFT....8J-32
INDICATOR - DESCRIPTION, VTSS........8Q-3
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-34
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-35
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-36
INDICATOR - DIAGNOSIS AND TESTING,
BRAKE.............................8J-16
INDICATOR - DIAGNOSIS AND TESTING,
FOUR-WHEEL DRIVE..................8J-29
INDICATOR - DIAGNOSIS AND TESTING,
HIGH BEAM.........................8J-21
INDICATOR - DIAGNOSIS AND TESTING,
TURN SIGNAL
.......................8J-32
INDICATOR - DIAGNOSIS AND TESTING,
VTSS
...............................8Q-4
INDICATOR - DIAGNOSIS AND TESTING,
WASHER FLUID
......................8J-35
INDICATOR - OPERATION, ABS
..........8J-14
INDICATOR - OPERATION, AIRBAG
.......8J-15
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-15
INDICATOR - OPERATION, CHECK
GAUGES
............................8J-17
INDICATOR - OPERATION, CRUISE
.......8J-18
INDICATOR - OPERATION, GEAR
SELECTOR
..........................8J-21
INDICATOR - OPERATION, HIGH BEAM
....8J-21
INDICATOR - OPERATION, LOW FUEL
.....8J-22
INDICATOR - OPERATION, OVERDRIVE
OFF
...............................8J-26
INDICATOR - OPERATION, SEATBELT
.....8J-27
16 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

LINE COUPLERS - OPERATION, A/C......24-41
LINE COUPLERS - STANDARD
PROCEDURE, A/C....................24-44
LINE LEAKS - DIAGNOSIS AND TESTING,
HIGH-PRESSURE FUEL................14-78
LINER - INSTALLATION, REAR
WHEELHOUSE.......................23-96
LINER - REMOVAL, REAR WHEELHOUSE . . 23-96
LINES - CLEANING AND INSPECTION,
OIL COOLER........................9-179
LINES - DESCRIPTION, FUEL............14-8
LINES - DESCRIPTION, HIGH PRESSURE
FUEL..............................14-78
LINES - DESCRIPTION, REFRIGERANT....24-40
LINES - DESCRIPTION, VACUUM........25-37
LINES - OPERATION, HIGH PRESSURE
FUEL..............................14-78
LINES - OPERATION, REFRIGERANT......24-41
LINK CONNECTOR - DESCRIPTION, DATA . 8E-12
LINK CONNECTOR - OPERATION, DATA . . . 8E-12
LINKAGE - 2WD - DESCRIPTION........19-40
LINKAGE - 2WD - INSTALLATION........19-41
LINKAGE - 2WD - REMOVAL............19-40
LINKAGE - 4WD - DESCRIPTION........19-42
LINKAGE - 4WD - INSTALLATION........19-43
LINKAGE - 4WD - REMOVAL............19-42
LINKAGE - INSTALLATION...............6-16
LINKAGE - REMOVAL..................6-15
LINKAGE, SPECIAL TOOLS - STEERING . . . 19-41,
19-44
LINK/COIL SUSPENSION - STANDARD
PROCEDURE, ALIGNMENT...............2-5
LINK/COIL SUSPENSION, SPECIAL
TOOLS..............................2-16
LIQUID LINE - INSTALLATION...........24-52
LIQUID LINE - REMOVAL..............24-52
LOAD TEST - STANDARD PROCEDURE....8F-12
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS, SPECIFICATIONS - BODY
SEALER............................23-47
LOCATIONS, SPECIFICATIONS -
STRUCTURAL ADHESIVE...............23-44
LOCATIONS, SPECIFICATIONS - WELD.....23-4
LOCK & REMOTE KEYLESS ENTRY
SYSTEM - DIAGNOSIS AND TESTING,
POWER.............................8N-5
LOCK - STANDARD PROCEDURE,
HYDROSTATIC...............9-11,9-122,9-66
LOCK CYLINDER - DIAGNOSIS AND
TESTING, IGNITION SWITCH AND KEY.....19-9
LOCK CYLINDER - INSTALLATION.......23-74
LOCK CYLINDER - INSTALLATION.......19-10
LOCK CYLINDER - REMOVAL...........23-74
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, POWER....8N-7
LOCK MOTOR - DIAGNOSIS AND
TESTING, POWER.....................8N-7
LOCK MOTOR - OPERATION, POWER.....8N-7
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - DESCRIPTION, POWER . . . 8N-8
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER.............8N-6
LOCK SWITCH - DIAGNOSIS AND
TESTING, POWER.....................8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER...........................8N-6
LOCK SWITCH - OPERATION, DOOR
CYLINDER...........................8N-5
LOCK SWITCH - OPERATION, POWER.....8N-8
LOCK SWITCH - REMOVAL, DOOR
CYLINDER...........................8N-6
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-4
LOCKS - OPERATION, POWER
...........8N-3
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING
......................8O-29
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING
......................8O-29
LOOP HGT ADJUSTER KNOB -
INSTALLATION, TURNING
..............8O-30
LOOP HGT ADJUSTER KNOB -
REMOVAL, TURNING
.................8O-30LOW FUEL INDICATOR - DESCRIPTION . . . 8J-22
LOW FUEL INDICATOR - OPERATION.....8J-22
LOW MOUNTED - INSTALLATION, SIDE
VIEW MIRROR.......................23-98
LOW MOUNTED - REMOVAL, SIDE VIEW
MIRROR...........................23-98
LOW PRESSURE SWITCH -
DESCRIPTION, A/C...................24-21
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C...................24-21
LOW PRESSURE SWITCH -
INSTALLATION, A/C...................24-21
LOW PRESSURE SWITCH - OPERATION,
A/C................................24-21
LOW PRESSURE SWITCH - REMOVAL,
A/C................................24-21
LOWER - INSTALLATION, LATCH........23-80
LOWER - INSTALLATION, LATCH
STRIKER...........................23-82
LOWER - REMOVAL, LATCH............23-80
LOWER - REMOVAL, LATCH STRIKER....23-82
LOWER BALL JOINT - DIAGNOSIS AND
TESTING............................2-10
LOWER CONTROL ARM - INSTALLATION . . 2-10,
2-20
LOWER CONTROL ARM - REMOVAL . . 2-10,2-20
LOWER FASCIA - INSTALLATION, FRONT . . . 13-3
LOWER FASCIA - REMOVAL, FRONT......13-3
LUBRICANTS - STANDARD PROCEDURE,
CLASSIFICATION OF....................0-1
LUBRICATION - DESCRIPTION....9-174,9-42,9-98
LUBRICATION - DESCRIPTION, AXLE.......0-5
LUBRICATION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-63,9-8
LUBRICATION - OPERATION....9-174,9-42,9-98
LUBRICATION - STANDARD PROCEDURE . 19-40,
19-42
LUMBAR CONTROL SWITCH -
DESCRIPTION.......................8N-18
LUMBAR CONTROL SWITCH -
OPERATION.........................8N-19
LUMBAR CONTROL SWITCH - REMOVAL . 8N-19
LUMBAR MOTOR - DESCRIPTION.......8N-19
LUMBAR MOTOR - DIAGNOSIS AND
TESTING...........................8N-19
LUMBAR MOTOR - OPERATION.........8N-19
LUMBAR SUPPORT - INSTALLATION....23-133
LUMBAR SUPPORT - REMOVAL........23-132
MAIN BEARING CLEARANCE -
STANDARD PROCEDURE...............9-159
MAIN BEARING FITTING - STANDARD
PROCEDURE, CRANKSHAFT.............9-31
MAIN BEARINGS - DESCRIPTION,
CRANKSHAFT........................9-31
MAIN BEARINGS - INSTALLATION,
CRANKSHAFT....................9-32,9-88
MAIN BEARINGS - OPERATION,
CRANKSHAFT........................9-31
MAIN BEARINGS - REMOVAL,
CRANKSHAFT....................9-31,9-88
MAIN BEARINGS - STANDARD
PROCEDURE, FITTING CRANKSHAFT......9-88
MAINTENANCE SCHEDULES -
DESCRIPTION.........................0-7
MALFUNCTION INDICATOR LAMP MIL -
DESCRIPTION.......................8J-23
MALFUNCTION INDICATOR LAMP MIL -
OPERATION.........................8J-23
MANAGER - DESCRIPTION, TASK........25-17
MANAGER - OPERATION, TASK.........25-21
MANIFOLD - CLEANING, EXHAUST . 9-109,9-185,
9-53
MANIFOLD - CLEANING, INTAKE . . . 9-107,9-184,
9-51
MANIFOLD - DESCRIPTION, EXHAUST . . . 9-109,
9-53
MANIFOLD - DESCRIPTION, FUEL DRAIN . . 14-89
MANIFOLD - DESCRIPTION, INTAKE . . 9-106,9-50
MANIFOLD - INSPECTION, EXHAUST
.....9-109,
9-186,9-53
MANIFOLD - INSPECTION, INTAKE
. 9-108,9-184,
9-51
MANIFOLD - INSTALLATION, EXHAUST
. . . 9-109,
9-186,9-53
MANIFOLD - INSTALLATION, FUEL
DRAIN
.............................14-90
MANIFOLD - INSTALLATION, INTAKE
.....9-108,
9-184,9-51MANIFOLD - OPERATION, EXHAUST . . 9-109,9-53
MANIFOLD - OPERATION, FUEL DRAIN . . . 14-89
MANIFOLD - OPERATION, INTAKE........9-50
MANIFOLD - REMOVAL, EXHAUST . . 9-109,9-185,
9-53
MANIFOLD - REMOVAL, FUEL DRAIN.....14-90
MANIFOLD - REMOVAL, INTAKE . . . 9-107,9-184,
9-50
MANIFOLD LEAKAGE - DIAGNOSIS AND
TESTING, INTAKE................9-106,9-50
MANUAL - NV4500 - ASSEMBLY........21-21
MANUAL - NV4500 - CLEANING.........21-20
MANUAL - NV4500 - DESCRIPTION.......21-1
MANUAL - NV4500 - DIAGNOSIS AND
TESTING............................21-3
MANUAL - NV4500 - DISASSEMBLY.......21-5
MANUAL - NV4500 - INSPECTION.......21-20
MANUAL - NV4500 - INSTALLATION......21-37
MANUAL - NV4500 - OPERATION.........21-3
MANUAL - NV4500 - REMOVAL..........21-4
MANUAL - NV4500 - SPECIFICATIONS....21-38
MANUAL - NV5600 - ASSEMBLY........21-64
MANUAL - NV5600 - CLEANING.........21-63
MANUAL - NV5600 - DESCRIPTION......21-46
MANUAL - NV5600 - DIAGNOSIS AND
TESTING...........................21-48
MANUAL - NV5600 - DISASSEMBLY......21-49
MANUAL - NV5600 - INSPECTION.........21-63
MANUAL - NV5600 - INSTALLATION......21-78
MANUAL - NV5600 - OPERATION........21-48
MANUAL - NV5600 - REMOVAL.........21-49
MANUAL - NV5600 - SPECIFICATIONS....21-79
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-7
MANUAL TRANSMISSION -
DESCRIPTION.........................0-5
MANUAL TRANSMISSION -
INSTALLATION, SHIFT BOOT...........23-122
MANUAL TRANSMISSION - REMOVAL,
SHIFT BOOT........................23-122
MAP SENSOR - INSTALLATION.........14-108
MARKER LAMP - INSTALLATION........8L-23
MARKER LAMP - REMOVAL............8L-23
MASTER CYLINDER - DESCRIPTION......5-26
MASTER CYLINDER - INSTALLATION......5-28
MASTER CYLINDER - OPERATION........5-26
MASTER CYLINDER - REMOVAL..........5-27
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-27
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-26
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-3
MATS - INSTALLATION, CARPETS AND
FLOOR............................23-123
MATS - REMOVAL, CARPETS AND
FLOOR............................23-123
MEASUREMENT - STANDARD
PROCEDURE, CASTER CORRECTION.......2-3
MEASUREMENTS, SPECIFICATIONS -
BODY GAP AND FLUSH................23-56
MEASURING TIMING CHAIN STRETCH -
INSPECTION....................9-111,9-54
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS . . . 9-116,9-6,9-61
MECHANISM - DESCRIPTION, SHIFT....21-208,
21-379
MECHANISM - NV4500 - INSTALLATION,
SHIFT..............................21-44
MECHANISM - NV4500 - REMOVAL,
SHIFT..............................21-43
MECHANISM - OPERATION, SHIFT......21-208,
21-379
METRIC SYSTEM - DESCRIPTION......Intro.-9
MICRO-RELAY - DESCRIPTION.......8W-97-13
MICRO-RELAY - DIAGNOSIS AND
TESTING........................8W-97-14
MICRO-RELAY - INSTALLATION......8W-97-14
MICRO-RELAY - OPERATION........8W-97-14
MICRO-RELAY - REMOVAL
..........8W-97-14
MIDTRONICS ELECTRICAL TESTER -
STANDARD PROCEDURE, USING
........8F-15
MIL - DESCRIPTION, MALFUNCTION
INDICATOR LAMP
....................8J-23
MIL - OPERATION, MALFUNCTION
INDICATOR LAMP
....................8J-23
MILE, SPECIFICATIONS - TIRE
REVOLUTIONS PER
....................22-9
BR/BEINDEX 19
Description Group-Page Description Group-Page Description Group-Page