2002 CHEVROLET AVALANCHE lock

6-39
3. Pull the pins away from their clips and pull them up
until they completely release from the vehicle.
4. Pull the headlamp assembly out of the vehicle.
A. Low-Beam Headlamp
B. High
-Beam Headlamp
5. Turn the bulb connector counterclockwise and pull it
out of the housing.
6. Unplug the electrical connector from the old bulb.

6-40
7. Plug in the electrical connector to the new bulb.
Use care not to touch the new bulb with your bare
hands or anything damp or oily.
8. Place the connector with the new bulb into the
headlamp housing and turn it clockwise until
it is tight.
9. Put the headlamp assembly back into the vehicle
and reinstall the two pins.
10. Place the inboard end of the turn signal/parking
lamp housing into the pocket.
11. Push the outboard side of the housing in until
the release clip snaps into place.Front Turn Signal/Parking Lamp and
Sidemarker Lamps
A. Sidemarker Lamp
B. Front Turn Signal/Parking Lamp

6-41
1. Remove the turn
signal/parking lamp
housing by pressing
the release clip on the
outboard side of the
housing and pulling
the outboard end of the
housing toward you.
2. Pull the inboard side of the housing out from
the vehicle.
3. Press the locking release lever (the sidemarker lamp
does not have a locking release lever), turn the bulb
socket counterclockwise and remove it from the turn
signal/parking lamp housing.
4. Remove the old bulb from the bulb socket.
5. Put the new bulb into the bulb socket.
6. Put the bulb socket into the turn signal housing and
turn it clockwise until it locks (the sidemarker lamp
does not lock into place).
7. Place the inboard end of the turn signal/parking lamp
housing into the pocket.
8. Push the outboard side of the housing in until the
release clip snaps into place.Daytime Running Lamps (DRLs)
The DRLs are located in the front facia near the
foglamps. They can be identified by their square shape.
1. Reach under the front
facia and locate the DRL
housing. Be sure you are
not picking the foglamp
housing, which is near
the DRLs.
2. Turn the bulb socket counterclockwise and remove it
from the DRL housing.
3. Pull out the old bulb from the socket and put a
new bulb in.
4. Place the bulb socket back into the DRL housing
and turn it clockwise until it is tight.
Center High Mounted Stoplamp (CHMSL)
It is recommended that this component be replaced as a
unit by your dealer.

6-42 Taillamps
A. Stoplamp
B. Turn Signal Lamp
C. Back
-up Lamp
1. Open the tailgate.
2. Remove the two
rear lamp assembly
screws near the tailgate
latch and pull out the
lamp assembly.
3. Press the release tab
and turn the bulb
socket counterclockwise
to remove it from the
taillamp housing.
4. Pull the old bulb straight out from the socket.
5. Press a new bulb into the socket and turn the socket
clockwise into the taillamp housing until it clicks.
6. Reinstall the rear lamp assembly and tighten the screws.
7. Close the tailgate.

6-64
Instrument Panel Fuse Block
The fuse block access door
is on the driver's side edge
of the instrument panel.
Pull off the cover to access
the fuse block.
You can remove fuses with a fuse extractor which is
mounted to the fuse block access door. To remove fuses
if you don't have a fuse extractor, hold the end of the
fuse between your thumb and index finger and pull
straight out.
You may have spare fuses located behind the fuse block
access door. These can be used to replace a bad fuse.
However, make sure it is of the correct amperage.
NAME Usage
L BODY Retained Accessory Power Relay
LOCK Power Door Locks
DRV UNLOCK Power Door Lock Relay
LOCK Power Door Lock Relay
HVAC 1 Climate Control System

6-65
NAME Usage
CRUISE Cruise Control, Instrument Cluster
IGN 3 Ignition, Power Seats
4WD Four
-Wheel Drive System,
Auxiliary Battery
CRANK Starting System
INT PRK Interior Lamps
L DOOR Power Door Lock Relay
BRAKE Anti
-Lock Brake System
RR WIPER Not Used
ILLUM Interior Lamps, Cargo Lamps
SEAT Power Seat Circuit Breaker
TURN Exterior Lamps, Turn Signals,
Hazard Lamps
UNLOCK Power Door Locks
HTR A/C Climate Control SystemNAME Usage
WS WPR Windshield Wipers
IGN 1 Ignition, Instrument Panel
AIR BAG Air Bag
MIR/LOCK Power Mirrors, Power Door Locks
DR LOCK Power Door Locks
PWR WDO Power Window Circuit Breaker
UNLOCK Power Door Lock Relay
IGN 0 PRND321 Display, Odometer,
VCM/PCM
SEO IGN Special Equipment Option, Ignition
SEO ACCY Special Equipment Option Accessory
RAP #1 Retained Accessory Power Relay
RDO 1 Audio System
RAP #2 Rear Power Windows,
Sunroof, Radio

6-66
Center Instrument Panel Utility Block
The center instrument panel utility block is located
underneath the instrument panel, to the left of the
steering column.
Relay Name Usage
SEO Special Equipment Option
HTD ST Heated Seats
SPARE Not UsedRelay Name Usage
VANITY Headliner Wiring
TRAILER Trailer Brake Wiring
PWR ST Power Seats
SPARE Not Used
UPF Upfitter
PARK LAMP Parking Lamps
*FRT PRK EXPT Not Used
SPARE 2 Not Used
PUDDLE LP Puddle Lamps
SL RIDE Not Used
SPARE 3 Not Used
INADV PWR Interior Lamps Feed
CTSY LP Courtesy Lamps
CEL PHONE Cellular Telephone Wiring

6-67
Underhood Fuse BlockThe underhood fuse block is located near the battery
on the driver's side of the vehicle. Lift the cover for
access to the fuse/relay block. See ªEngine
Compartment Overviewº in the Index for more
information on location.
You will see fuses to the top right of the fuse block
once you remove the cover. These are spare fuses and
can be used accordingly.
You can remove fuses with a fuse extractor. The fuse
extractor is located in the underhood fuse block.
To remove fuses if you don't have a fuse extractor,
hold the end of the fuse between your thumb and index
finger and pull straight out.