2002 CADILLAC SEVILLE buttons

2-88
Driver Information Center (DIC)
This display gives you the status of many of your
vehicle's systems. The DIC is also used to display driver
personalization features and warning/status messages.
All messages will appear in the DIC display, located at
the bottom of the instrument panel cluster.
DIC Controls and Displays
The Driver Information Center (DIC) buttons are
located to the right of the steering wheel on the
instrument panel, near the air outlets.INFO (Information): Pressing this button up or down
will display the OUTSIDE TEMP, MILES RANGE,
MPG AVG, MPG INST, GAL FUEL USED, AVG
MPH, TIMER, BATTERY VOLTS, LF
-RF-LR-RR
TIRE (If Equipped), ENGINE OIL LIFE, TRANS
FLUID LIFE, PHONE (Option) and FEATURE
PROGRAMMING and Blank Display.
INFO (Information) RESET: Pressing this button will
reset the MPG AVG, GAL FUEL USED, AVG MPH,
TIMER, ENGINE OIL LIFE and TRANS FLUID
LIFE. For more information about the trip odometer,
see ªOdometerº in the Index.

MPG AVG (Average Miles per Gallon): This
message shows the approximate fuel economy you
have averaged since the last time you reset the value.
To reset the MPG AVG (Average Fuel Economy),
press the INFO button to display the MPG AVG
then press and hold the INFO RESET button until
0.0 MPG AVG is displayed.

GAL (Gallons) FUEL USED: This message shows
how much fuel has been used since the last reset.
To learn how much fuel is used from a new starting
point, press the RESET button while the GAL FUEL
USED is displayed in the DIC.

2-110
Tire Pressure Display (If Equipped)
This feature will allow the individual tire pressure
readings to be displayed when using the INFO button to
scroll through the DIC displays. Even with this feature
programmed to be turned off, a low or high tire pressure
condition will still cause the CHECK TIRE PRESSURE
message to be displayed on the DIC. See ªDriver
Information Center (DIC) Messagesº in the Index
for more information.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, do the following:
1. Enter FEATURE PROGRAMMING following the
instructions listed previously.2. Press the down arrow on the INFO button until TIRE
PRESSURE DISPLAY appears on the DIC display.
3. To turn on the feature, press the ON/OFF button
until ON appears on the DIC display. To turn it off,
press the ON/OFF button until OFF appears on
the display.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Driver's Names Set/Recall (If Equipped)
This feature allows individual driver's names to be
displayed in the DIC when the ignition is turned to ON.
This feature only works when the remote keyless entry
transmitter is used to unlock the vehicle or when buttons
1 or 2 on the driver's door are pressed. See your dealer
for assistance in programming this feature.
Exiting Feature Programming
To exit FEATURE PROGRAMMING, press the
INFO RESET or INFO button.

2-113
Navigation (Option)
Navigation Display Controls
The display screen is located in the center on the
instrument panel. There are ªhardº buttons and
a touch sensitive screen.Your vehicle may be equipped with a turn by turn
navigation guidance system that includes a CD ROM
map media covering nine regional areas throughout
the contiguous United States and Canada. In addition,
the system includes intersection and freeway entrances,
route planning, a programmable address book, points of
interest, a list of restaurants, emergency phone numbers,
and a list of hotels and motels for all of the major
cities on the CD. The navigation system can also
communicate with the radio data system to receive
broadcast announcements on traffic, weather
information and emergency alert communications.
For more information on how to use this system,
see ªNavigationº supplement.

3-13
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing this button.
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.
Finding a Station
BAND: Press this button to select AM, FM1 or FM2.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds
to scan radio stations and associated tone settings.
The radio will go to a station, play for five seconds,
then go on to the next station. Press this button again
to stop scanning.To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2), by performing the
following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds until you hear a beep.
5. Repeat the steps for each pushbutton. Whenever you
press that numbered pushbutton for less than
two seconds, the station you set will return.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.

3-15

RW (Rewind): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape rewinds.
You may use your station pushbuttons to tune to another
radio station while in rewind. Press the left arrow again
to return to playing speed.
FF
 (Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances. You may use your station
pushbuttons to tune to another radio station while in
fast forward. Press the right arrow again to return to
playing speed.
~' SEEK !': Press the up or down arrow to seek to
the next or previous selection on the tape. Your tape
must have at least three seconds of silence between each
selection for the SEEK arrows to work. The sound will
mute while seeking.
SCAN: Press this button to listen to selections for a
few seconds. The tape will go to a selection, play for a
few seconds, then go on to the next selection. Press this
button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing.
(Eject): Press this button to the right of the
cassette tape player to remove a tape. The radio will
play. Eject may be activated with the radio off and/or
the ignition off.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape, it
could be for one of the following reasons:

The cassette tape is tight and the cassette player
cannot turn the hubs of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.

The cassette tape is broken. (Check to see if your
tape is broken. Try a new tape.)
CLEAN TAPE: If this message appears on the display,
the cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer.

3-18
AVC (Automatic Volume Control): With AVC, your
audio system monitors the noise in the vehicle. Then,
AVC adjusts the volume level so that it always sounds
the same to you. To use AVC, press and hold the TONE
button until AUTO VOLUME CONTROL OFF appears
on the display. Then press the LEVEL plus symbol.
AUTO VOLUME CONTROL ON will appear on the
display. AVC VOLUME will appear on the display any
time you adjust the volume while AVC is on. To turn
AVC off, press and hold the TONE button until AUTO
VOLUME CONTROL ON appears on the display. Then
press the LEVEL minus symbol. AUTO VOLUME
CONTROL OFF will appear on the display.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing this button.
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.Finding a Station
BAND: Press this button to select AM, FM1 or FM2,
weather or XM1 or XM2 if your radio is equipped with
XM
Satellite Radio Service.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds to
scan radio stations. The radio will go to a station, play
for five seconds, then go on to the next station. Press
this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.

3-19
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations and associated tone and DSP settings.
The RDS PTY mode must be off to use this mode. You
can set up to 36 stations (six AM, six FM1, six FM2,
six XM1, six XM2 and six weather if your radio is
equipped with the XM Satellite Radio Service), by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1, FM2, XM1, XM2
or weather.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds. Whenever you press that
numbered pushbutton for less than two seconds, the
station you set will return.
5. Repeat the steps for each pushbutton.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.Setting the Tone (Bass/Treble)
TONE: Press and release this button until the desired
tone BASS, TREBLE or MIDRANGE appears on the
display. The radio keeps separate tone settings for each
band, preset (except weather band presets) and source.
- LEVEL +: After selecting the desired tone control,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered button for the desired preset for more than
two seconds until you hear a beep.
Adjusting the Speakers (Balance/Fade)
TONE: Press and release this button until BALANCE
or FADE appears on the display.
- LEVEL +: After selecting the desired control, press
the plus or minus symbol on this button to select the
desired level.
To save the tone settings for your presets, press and hold
the numbered pushbutton for the desired preset for more
than two seconds until you hear a beep.

3-21
HR (Hour) or MN (Minute): When tuned to an RDS
station, press these buttons to display the time for the
current station. STATION TIME IS will be displayed.
If a time has not been sent to the radio, NO STATION
TIME will be displayed. If you have recently tuned to
the station, you may need to wait a minute before the
time is available to the radio. To set the clock to the
current displayed station time, press HR or MN until
TIME UPDATED is displayed. You must be tuned to
an FM RDS station.
RDS Messages
ALERT: This type of announcement warns of national
or local emergencies. You will not be able to turn off
alert announcements. ALERT appears on the display
when an alert announcement plays. The radio uses
TA volume during these announcements. To increase
volume, turn the PWR/VOL knob clockwise. Turn it
counterclockwise to decrease volume. TA VOLUME
will appear on the display while the volume is being
adjusted. When an alert announcement comes on the
current radio station or a related network station, you
will hear it, even if the volume is muted or a cassette
tape or compact disc is playing. If the radio tunes to arelated network station for an alert announcement, it will
return to the original station when the announcement is
finished. If the cassette tape or compact disc player is
playing, play will stop for the announcement and resume
when the announcement is finished.
TA (Traffic Announcement): This feature allows
the radio to receive traffic announcements even with
the volume muted, or when listening to a CD or
cassette tape.
When the TA button is pressed and released, the radio
will search for a station with TA if the current station is
not TA capable. During the search TA will flash on the
display. Once a TA station is found, TA will appear on the
display and the traffic announcement will be played. If no
station broadcasting traffic announcements is found, NO
TRAFFIC STATION FOUND will appear on the display.
If the TA button is pressed and held for two seconds, the
radio will search for the next available TA station.
While a traffic announcement plays, the radio uses a
special type of volume called TA volume. To increase
TA volume, turn the VOL knob clockwise. Turn it
counterclockwise to decrease volume. TA VOLUME will
appear on the display while the volume is being adjusted.