2002 CADILLAC ELDORADO change time

2-86
STABILITY ENGAGED - 55: You may see
the STABILITY ENGAGED message on the
Driver Information Center. It means that an advanced,
computer
-controlled system has come on to help
your vehicle continue to go in the direction in which
you're steering. This stability enhancement system
activates when the computer senses that your vehicle is
just starting to spin, as it might if you hit a patch of ice
or other slippery spot on the road. When the system is
on, you may hear a noise or feel a vibration in the brake
pedal. This is normal.
When the STABILITY ENGAGED message is on,
you should continue to steer in the direction you want
to go. The system is designed to help you in bad
weather or other difficult driving situations by making
the most of whatever road conditions will permit. If the
STABILITY ENGAGED message comes on, you'll
know that something has caused your vehicle to start to
spin, so you should consider slowing down.STARTING DISABLED REMOVE KEY
- 33: This
message will appear when the PASS
-Key
II system
senses that an improper ignition key is being used to try
to start the vehicle. Check the ignition key for damage.
If it is damaged, it may need to be replaced. If you see
no damage, clean the pellet contacts with a soft cloth or
napkin. Remove the ignition key and wait for the DIC
to display WAIT 3 MINUTES. The instrument panel
cluster will then run a timer and change the messages
to WAIT 2 MINUTES, WAIT 1 MINUTE and then
START CAR. When the START CAR message is
displayed, try again to start the engine.
THEFT SYSTEM PROBLEM, CAR MAY NOT
RESTART
- 34: This message means there is a problem
in the PASS
-Key
II system. A fault has been detected
in the system which means that the PASS
-Key
II
system is disabled and is not protecting the vehicle.
The vehicle usually restarts, however, you may want to
take your vehicle to a proper service center before
turning off the engine.

2-95
Exiting Feature Programming
To exit the feature programming mode, do the following:
1. Scroll through all remaining programming modes by
pressing the SKIP INFO button. STORAGE MODE
will be the last mode.
2. Turn the ignition to LOCK. Your selections will
be saved.
Comfort Controls and Radio System Personalization
These features allow both drivers to personalize their own
climate control settings as well as their radio settings. For
more information, see ªClimate Control Personalizationº
and ªRadio Personalizationº in the Index.
Continuous Variable Road Sensing
Suspension (CVRSS) (ETC Only)
The CVRSS automatically adjusts the ride of your
vehicle. Automatic ride control is achieved through a
computer used to control and monitor the suspension
system. The controller receives input from various
sensors to determine the proper system response.
If the controller detects a problem within the system,
the Driver Information Center (DIC) will display a
SERVICE RIDE CONTROL message. If this message
appears, have your vehicle serviced at your dealership.
Oil Life Indicator
This feature lets you know when to change the engine
oil. It's based on the engine oil temperatures and your
driving patterns. To see the display, press the SKIP
INFO button several times until XX OIL LIFE LEFT
appears. If you see 99% OIL LIFE LEFT, 99 percent
of your current oil life remains.
The Driver Information Center (DIC) may display a
CHANGE ENGINE OIL message. Always keep a
written record of the mileage and date when you changed
your oil. For more information, see ªMaintenance
Scheduleº in the Index. If you see CHANGE ENGINE
OIL, it means that you have no oil life left and you
should change your engine oil right away.
When the oil is changed, you'll need to reset the system.
See ªOil Life Indicator, How to Resetº in the Index.

3-6
To avoid blowing cold air in cold weather, the system
will delay turning on the fan until warm air is available.
The length of delay depends on the outside air
temperature, engine coolant temperature or the
time since the engine was last started. As the coolant
warms up, the fan speed will gradually increase and
air will flow from the floor outlets, with some airflow
to the windshield to prevent fogging under most
normal conditions.
If you leave your vehicle, the system will remember
the control setting the next time you start your engine,
except for recirculation and defrost. Each ignition cycle
cancels recirculation, whereas, defrost mode will change
to automatic operation when the ignition is shut off and
then turned back on.Electronic Solar Sensor
The sensor monitors the sun's solar radiation and
is located on top of the instrument panel near the
windshield. The electronic climate control panel uses
this information to automatically make the necessary
temperature and airflow adjustments to maintain
your comfort.

3-7 Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
Press the AC button or the TEMP/AUTO knob to turn
the system on and then select the proper mode to direct
airflow. The system will cool and dehumidify the air
inside the vehicle. Also while in the AUTO mode, the
system will use recirculation as necessary to cool the air.
You may also need to adjust the interior temperature and
the fan speed as needed.
When the air conditioner is on, you may sometimes
notice slight changes in your vehicle's engine speed
and power. This is normal because the system is
designed to cycle the compressor on and off to
maintain the desired temperature.
Heating
Press the MODE switch to select the heater mode.
Adjust the interior temperature to a comfortable level
and if the fan speed needs adjusting, press the up or
down arrow.
Outside air will be brought in and sent through the floor,
air conditioning or bi
-level outlets (depending on the
condition). The heater works best if you keep your
windows closed while using it.
Defogging and Defrosting
Use defrost to remove fog or ice from the windshield
quickly in extremely humid or cold conditions.
Press the MODE switch. If you select defrost mode,
adjust the fan speed by pressing the fan switch up or
down. If you select defrost mode from AUTO, the
system will control the fan speed. The temperature also
needs to be adjusted by turning the TEMP/AUTO knob.
Recirculation is not available in the defrost or defog modes.

3-10 HVAC Steering Wheel Controls
Some heating and cooling
controls can be adjusted at
the steering wheel. Other
touch controls operate some
audio controls. See ªAudio
Steering Wheel Controlsº
in the Index.
(Fan): Press the up arrow lever to increase the fan
speed and the down arrow lever to decrease fan speed.
TEMP: Press the up arrow lever to increase
the temperature and the down arrow lever to
decrease temperature.
Climate Control Personalization (If Equipped)
This feature allows both drivers (driver 1 or 2 depending
on the number on the back of your remote keyless entry
transmitter) to personalize their own climate control
settings. For more information, see ªMemory and
Personalization Featuresº in the Index.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off.
See ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two
-second delay before the clock
goes into time
-set mode.

3-14


REV (Reverse): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape reverses
and REV will appear on the display. You may use your
station pushbuttons to tune to another radio station while
in reverse mode. Press the left arrow again to return to
playing speed.
FF
(Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances and FF will appear on the
display. You may use your station pushbuttons to
tune to another radio station while in fast forward mode.
Press the right arrow again to return to playing speed.


SEEK
: Press the right arrow to seek to the next
selection on the tape. Press the left arrow to search for
the previous selection on the tape (REP will appear on
the display). Your tape must have at least three seconds
of silence between each selection for seek to work. The
sound will mute while seeking.SCAN: Press this button to listen to selections for a
few seconds. SCAN FF will appear on the display until
the next selection is found and then SCAN PLAY will
appear on the display. The tape will go to a selection,
play for a few seconds, then go on to the next selection.
Press this button again to stop scanning.
~SIDE!: Press this button to change the side of the
tape that is playing. (PLAY shows on the display.)


SOURCE
: Press this button to select a source.
If no cassette tape is in the tape player, CASS appears
on the display and then the radio station appears briefly.
The display then reverts back to showing the time of
day. Press this button again or press BAND to switch
back to the radio.
(Eject): Press this button to stop a tape when
it is playing or to eject a tape when it is not playing.
Eject may be activated with the radio off. Cassette tapes
may be loaded with the radio off but they will not start
playing until the PWR knob is pressed. Press PWR
or turn the ignition off to stop the cassette tape player.
The tape will stay in the player and resume play at the
point where it stopped.

3-29
Whenever a CD magazine with discs is loaded in the
changer, the CD changer symbol will appear on the
radio display. If the CD changer is checking the
magazine for CDs, the CD symbol will flash on the
display until the changer is ready to play. When a
CD begins playing, a disc and track number will be
displayed. The disc numbers are listed on the front
of the magazine.
All of the CD functions are controlled by the radio
buttons, except for ejecting the CD magazine.
PUSHBUTTONS: Press pushbuttons one through six
to select compact discs one through six. Press and hold
one of the six pushbuttons until a beep sounds to
select compact discs 7 through 12. These pushbuttons
represent the order of the discs loaded in the changer.
DSPL (Display): Press and hold this button to see
the track elapsed time. (This button is available on the
AM
-FM Stereo with Cassette Tape Player only.)
< hold this button to reverse quickly through a track.
FF >> (Fast Forward): Press and hold this button to
advance quickly through a track.
~'SEEK TUNE!': Press the right arrow to seek to
the next track. Press the left arrow to search for the
previous track. The sound will mute while seeking.
~'TUNE SEEK!': Press this up arrow to seek to the
next track. Press the down arrow to seek to the previous
previous track. The sound will mute while seeking.
SCAN: Press this button to hear the first few seconds
of the first track on each disc. Press this button again
to stop scanning.
To scan tracks, press SCAN for less than two seconds.
You will hear the first few seconds of each track on a disc.
Press SCAN again to stop scanning. The CD will mute
while scanning and SCAN will appear on the display.
RDM (Random): Press this button to hear the tracks
in random, rather than sequential, order. RANDOM will
appear on the display. Press SEEK while RDM is on the
display to randomly seek through discs. Press RDM
again to turn off random play. (This button is not
available on the AM
-FM Stereo with Cassette
Tape Player.)

3-30
SIDE: Press this button to select the next disc in the
changer. If your vehicle is equipped with the AM
-FM
Stereo with Cassette Tape Player, CD and the disc
number will appear on the display each time you press
this button. If your vehicle is equipped with any other
audio system, DISC LOADING will appear on the
display and the disc number on the radio display will
go to that of the next available CD each time you press
this button.
SOURCE: Press this button to select a source.
The audio source must be loaded to play. If none of
the audio sources are loaded, NO SOURCE LOADED
will appear on the display. (CD will be displayed for
a few seconds instead on the AM
-FM Stereo with
Cassette Tape Player, then the radio will play.) Press this
button again or press BAND to switch back to the radio.
Slide the CD changer door all the way open and the disc
holder will automatically eject.Compact Disc Changer Errors
CD CHANGER ERROR could be displayed for one of
the following reasons:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or loaded label
side up.

The air is very humid. If so, wait about an hour
and try again.
CD CHANGER DOOR OPEN is displayed when
the CD changer door is left open. (CHEK DOOR will be
displayed instead on the AM-FM Stereo with Cassette
Tape Player.) Completely close the changer door to
restore normal operation.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer.