2002 CADILLAC DEVILLE bulb

2-43
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane
-Change Signals

Headlamp High/Low
-Beam Changer

Flash
-To-Pass Feature

Windshield Wipers

Windshield Washer
For more information on the exterior lamps, see
ªExterior Lampsº later in this section.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is complete.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns when it's released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON after driving about a mile to
remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned out signal bulb.
Other drivers won't see the turn signal.
Replace burned
-out bulbs to help avoid possible
accidents. Check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs if the
arrow fails to work when signaling a turn.

4-39 Making Turns
NOTICE:
Making very sharp turns while trailering could
cause the trailer to come in contact with the
vehicle. Your vehicle could be damaged. Avoid
making very sharp turns while trailering.
When you're turning with a trailer, make wider
turns than normal. Do this so your trailer won't
strike soft shoulders, curbs, road signs, trees or other
objects. Avoid jerky or sudden maneuvers. Signal well
in advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle may need a
different turn signal flasher and/or extra wiring. Check
with your dealer. The arrows on your instrument panel
will flash whenever you signal a turn or lane change.
Properly hooked up, the trailer lamps will also flash,
telling other drivers you're about to turn, change lanes
or stop.
When towing a trailer, the arrows on your instrument
panel will flash for turns even if the bulbs on the trailer
are burned out. Thus, you may think drivers behind you
are seeing your signal when they are not. It's important
to check occasionally to be sure the trailer bulbs are
still working.

6-
6-1
Section 6 Service and Appearance Care
Here you will find information about the care of your vehicle. This section begins with service and fuel information,
and then it shows how to check important fluid and lubricant levels. There is also technical information about your
vehicle, and a part devoted to its appearance care.
6
-2 Service
6
-3 Fuel
6
-5 Fuels in Foreign Countries
6
-6 Filling Your Tank
6
-9 Filling a Portable Fuel Container
6
-9 Checking Things Under the Hood
6
-12 Engine Oil
6
-17 Engine Air Cleaner/Filter
6
-21 Automatic Transaxle Fluid
6
-25 Engine Coolant
6
-28 Surge Tank Pressure Cap
6
-29 Power Steering Fluid
6
-30 Windshield Washer Fluid
6
-31 Brakes
6
-34 Battery
6
-36 Bulb Replacement
6
-47 Windshield Wiper Blade Replacement6
-48 Tires
6
-59 Appearance Care
6
-59 Cleaning the Inside of Your Vehicle
6
-64 Cleaning the Outside of Your Vehicle
6
-65 Cleaning Aluminum or Chrome-Plated
Wheels (If Equipped)
6
-66 Underbody Maintenance
6
-66 Chemical Paint Spotting
6
-67 GM Vehicle Care/Appearance Materials
6
-68 Vehicle Identification Number (VIN)
6
-68 Service Parts Identification Label
6
-69 Electrical System
6
-73 Removing the Rear Seat Cushion
6
-77 Replacement Bulbs
6
-77 Capacities and Specifications
6
-78 Normal Maintenance Replacement Parts

6-36
Bulb Replacement
For the proper type of replacement bulb, see
ªReplacement Bulbsº in the Index.
For any bulb changing procedure not listed in this
section, contact your dealer.
Halogen Bulbs
CAUTION:
Halogen bulbs have pressurized gas inside and
can burst if you drop or scratch the bulb. You or
others could be injured. Be sure to read and
follow the instructions on the bulb package.
Headlamps
1. To access the
headlamps, remove all
of the push
-pins that
hold the filler panel
cover in place.
2. Do this by pressing in
the center of each pin
and then pulling up on
the outer circle to
remove the pin.

6-38
6. Firmly grasp the outboard side of the headlamp
assembly with both hands and pull hard enough so
that the whole assembly separates from the vehicle.
7. Remove the bulb socket
dust cover.
8. Turn the headlamp
housing socket
counterclockwise to
unlock the socket from
the lamp housing.

6-39
9. Pull the old bulb out of
the socket.
10. Install the new bulb into the socket. Make sure that
the bulb is locked in firmly.
11. Reinstall the headlamp housing socket into the
headlamp assembly.
12. Reinstall the headlamp assembly by reversing
Steps 2 through 6.To reinstall the filler panel, do the following:
1. Place the filler panel in the correct location.
2. Reset each push
-pin by holding each by the outer
circle while pushing up on the pin assembly from
below. The center portion of the push
-pin should
now be above the outer circle.
3. After placing each push
-pin into the opening, press
down on the outer circle until it is seated against the
surface of the filler panel.
4. Lock each push
-pin in place by pressing the center
of each down until it is level with the outer circle.
Use care not to press down so far that the push
-pin
releases again.

6-45
6. Repeat Steps 4
and 5 for the
opposite headlamp.Front Cornering Lamps
1. Follow Steps 1 through 6 in ªHeadlampsº
described previously.
2. Disconnect the cornering lamp bulb by pulling the
bulb out of the socket. Do not twist or turn the bulb.
3. Replace cornering lamp bulb by pushing the new
bulb directly into the socket.
4. Reinstall the cornering lamp housing socket into the
headlamp assembly.
5. Reverse Steps 1 through 6 in ªHeadlampsº
described previously.

6-46 Front Turn Signal Lamps
1. The turn signal lamps are located beside the
headlamp bulbs. To access, lift off the bulb socket
dust cover. See Steps 1 through 6 under
ªHeadlampsº described previously.
2. Press the tab down and turn the housing
socket clockwise to unlock the socket from the
lamp housing.
3. Remove the turn signal lamp housing socket and
replace the bulb.
4. Reverse Steps 1 and 2 to reinstall.