2002 CADILLAC DEVILLE CD changer

2-43
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane
-Change Signals

Headlamp High/Low
-Beam Changer

Flash
-To-Pass Feature

Windshield Wipers

Windshield Washer
For more information on the exterior lamps, see
ªExterior Lampsº later in this section.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is complete.
An arrow on the instrument
panel cluster will flash in
the direction of the turn or
lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns when it's released.
If the turn signal is left on, a warning chime will sound
and the Driver Information Center (DIC) will display
TURN SIGNAL ON after driving about a mile to
remind you to turn it off.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned out signal bulb.
Other drivers won't see the turn signal.
Replace burned
-out bulbs to help avoid possible
accidents. Check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs if the
arrow fails to work when signaling a turn.

2-44
Headlamp High/Low-Beam Changer
Push forward to change the headlamps from low beam
to high. Pull the lever back and then release it to change
from high beam to low.
This light on the instrument
panel cluster will be on,
indicating high
-beam usage.
Flash-To-Pass
This feature lets you use the high-beam headlamps to
signal the driver in front of you that you want to pass.
Pull and hold the turn signal lever toward you to use.
When you do, the following will occur:

If the headlamps are either off or in the Daytime
Running Lamps (DRL) mode, the high
-beam
headlamps will turn on. They'll stay on as long as
you hold the lever there. Release the lever to turn
them off.

If the headlamps are on high beam, they will switch
to low beam. To return to high beam, push the lever
away from you.
Windshield Wipers
WIPER: Turn the band on the turn signal lever to
control the wipers.
MIST: Turn the band toward you to MIST and then
release it for a single wiping cycle. For more cycles,
hold the band on MIST longer.
LO or HI: Turn the band away from you to either
LO (low speed) or to HI (high speed), depending on
the wiper speed you want.
DELAY: Turn the band to one of the DELAY positions
to set the wiper speed for a long or a short delay
between wipes. The closer you move it to LO, the
shorter the delay.
OFF: Turn the band to OFF to turn off the wipers.

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Climate Control Panel
3
-6 Air Conditioning
3
-6 Heating
3
-6 Defogging and Defrosting
3
-7 Rear Window Defogger
3
-9 Ventilation System
3
-10 HVAC Steering Wheel Controls
3
-11 Climate Control Personalization (If Equipped)
3
-12 Audio Systems
3
-12 Setting the Clock
3
-12 AM-FM Stereo with Cassette Tape and
Compact Disc Player
3
-17 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Radio Data
Systems (RDS), Digital Signal Processing
(DSP) and XM
Satellite Radio Service
(If Equipped)3
-27 Navigation/Radio System (Option)
3
-28 Glovebox-Mounted CD Changer (Option)
3
-30 Radio Personalization with Home and Away
Feature (If Equipped)
3
-31 Theft-Deterrent Feature
3
-32 Audio Steering Wheel Controls
3
-32 Understanding Radio Reception
3
-33 Tips About Your Audio System
3
-34 Care of Your Cassette Tape Player
3
-35 Care of Your Compact Discs
3
-35 Care of Your Compact Disc Player
3
-36 Diversity Antenna System
3
-36 XM Satellite Radio Antenna System
(If Equipped)

3-28 Glovebox-Mounted CD Changer (Option)
With the compact disc changer, you can play up to
six discs continuously. Normal size discs may be played
using the trays supplied in the magazine. The smaller discs
(8 cm) can be played only with specially designed trays.
You must first load the magazine with discs before you
can play a compact disc. Each of the six trays holds one
disc. Load the trays from bottom to top, placing a disc in
the tray label side up. If you load a disc label side down,
the disc will not play and an error will occur. Repeat this
procedure for loading up to 6 discs in the magazine.
Once you have loaded the discs in the magazine, slide
open the door of the compact disc (CD) changer. Push
the magazine into the changer in the direction of the
arrow marked on top of the magazine.

3-29
Close the door by sliding it all the way to the right.
When the door is closed, the changer will begin
checking for discs in the magazine. This will continue
for up to one and a half minutes, depending on the
number of discs loaded.
Whenever a CD magazine with discs is loaded in the
changer, the CD changer symbol will appear on the
radio display. If the CD changer is checking the
magazine for CDs, the CD symbol will flash on the
display until the changer is ready to play. When a CD
begins playing, a disc and track number will be
displayed. The disc numbers are listed on the front of
the magazine.1 PREV (Previous): Press this pushbutton to seek to the
previous track on the CD. If playing the first track of the
CD, pressing the PREV pushbutton will seek to the last
track of the CD. The sound will mute while seeking.
2 NEXT: Press this pushbutton to seek to the next track
on the CD. If playing last track of the CD, pressing the
NEXT pushbutton will seek to the first track of the CD.
3 RW (Rewind): Press and hold this pushbutton to
reverse quickly through a track.
4 FF (Fast Forward): Press and hold this pushbutton to
advance quickly through a track.
5 DISC: Press this pushbutton to select the next disc in
the changer. Each time you press this button, LOADING
will appear on the display and the disc number on the
radio display will go to that of the next available CD.
6 RDM (Random): Press this pushbutton to hear the
tracks in random, rather than sequential, order. RDM
will appear on the display. Press the PREV or NEXT
pushbuttons while RDM is on the display to randomly
seek through discs. Press RDM again to turn off random
play. This feature may not be available on your radio.
SCAN: Press this button. You will hear the first few
seconds of the first track on each disc. Press this button
again to stop scanning. The CD will mute while
scanning and SCAN will appear on the display.

3-30
SOURCE: Press this button if you have a disc loaded in
the changer and the radio is on, to play a compact disc.
To return to playing the radio, press BAND. Pressing
source also switches between a tape or compact disc if
both are loaded.
EJECT: Slide the CD changer door all the way open.
Press the EJECT button and the magazine will eject.
Compact Disc Changer Errors
CD CHANGER ERROR could be displayed for one of
the following reasons:

The road is too rough. The disc should play when the
road is smoother.

The disc is dirty, scratched, wet or loaded label
side up.

The air is very humid. If so, wait about an hour and
try again.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer. If your radio displays an
error number, write it down and provide this information
to your dealer when reporting the problem.Radio Personalization with Home and Away
Feature (If Equipped)
If DRIVER 1 (HOME or AWAY) PRESETS or
DRIVER 2 (HOME or AWAY) PRESETS appears in the
display when the radio is first turned on, your vehicle is
equipped with this feature.
This feature allows the driver to return to the last used
audio source (radio, cassette or CD) using their remote
keyless entry transmitter. This feature can also store and
recall AM and FM presets, volume, tone and the last
selected radio station. The number on the back of each
transmitter (1 or 2) corresponds to driver 1 or 2. If
transmitter 1 is used to enter the vehicle, the last used
audio source and/or settings set by driver 1 will be
recalled. If transmitter 2 is used to enter the vehicle, the
last used audio source and/or settings set by driver 2 will
be recalled. The settings can also be recalled by pressing
the MEMORY seat buttons 1 or 2 located on the
driver's door.