2002 BUICK RANDEZVOUS clock

5-34
Storing the Spare Tire and Tools
1. Lay the compact spare tire on the ground at the
rear of the vehicle. Position the compact spare tire
so that the valve stem is pointed down facing the rear
of the vehicle.
2. Lower the cable to the ground. See ªRemoving
the Spare Tire (Vehicles without the Rear
Convenience/Cargo Tray)º or ªRemoving the Spare
Tire (Vehicles with the Rear Convenience/Cargo
Tray)º in the Index.
3. Tilt the retainer downward and slip it through the
center hole of the spare tire.
Make sure the retainer is fully seated across the
underside of the wheel.
4. Attach the folding wrench to the hoist shaft.5. Turn the folding wrench clockwise to lift the
spare tire.
6. When the tire reaches the stabilizer bar, move the
tire over the bar, then continue to turn the folding
wrench clockwise to lift the spare tire.
7. When the tire is almost in the stored position,
turn the tire so that the valve stem is towards the
rear of the vehicle.
This will help when you check and maintain tire
pressure in the spare.
8. Raise the tire fully against the underside of the
vehicle. Continue turning the folding wrench until
you feel more than two clicks. This indicates that the
compact spare tire is secure and the cable is tight.
The spare tire hoist cannot be overtightened.

6-6
Filling Your Tank
CAUTION:
Gasoline vapor is highly flammable. It burns
violently, and that can cause very bad injuries.
Don't smoke if you're near gasoline or refueling
your vehicle. Keep sparks, flames and smoking
materials away from gasoline.
The fuel cap is located
on the driver's side of
the vehicle.
While refueling, let the
fuel cap hang by the tether
as shown.
To remove the fuel cap, turn it slowly to the left
(counterclockwise). The fuel cap has a spring in it;
if you let go of the cap too soon, it will spring back
to the right.

6-7
CAUTION:
If you get gasoline on yourself and then
something ignites it, you could be badly burned.
Gasoline can spray out on you if you open the
fuel cap too quickly. This spray can happen if
your tank is nearly full, and is more likely in hot
weather. Open the fuel cap slowly and wait for
any ªhissº noise to stop. Then unscrew the cap all
the way.
Be careful not to spill gasoline. Clean gasoline from
painted surfaces as soon as possible. See ªCleaning the
Outside of Your Vehicleº in the Index.
When you put the fuel cap back on, turn it to the right
(clockwise) until you hear a clicking sound. Make sure
you fully install the cap. The diagnostic system can
determine if the fuel cap has been left off or improperly
installed. This would allow fuel to evaporate into the
atmosphere. See ªMalfunction Indicator Lampº in
the Index.The malfunction indicator lamp (SERVICE ENGINE
SOON or CHECK ENGINE light) will come on if the
fuel cap is not properly installed.
NOTICE:
If you need a new fuel cap, be sure to get the
right type. Your dealer can get one for you.
If you get the wrong type, it may not fit properly.
This may cause your malfunction indicator lamp
to light and may damage your fuel tank and
emissions system. See ªMalfunction Indicator
Lampº in the Index.

6-36 Headlamps
1. Open the hood.
2. Push in on the headlamp
panel and lift up the
headlamp retaining
clip partway, but do
not remove.
3. Undo the wing stud on the upper, outboard side of
the lamp assembly.
4. Unsnap the headlamp assembly by pulling it
forward, away from the vehicle.
5. Disconnect the electrical connector by pulling back
on the locking tab, located on the electrical
connector, to separate the two connectors.
6. Turn the bulb
socket one
-quarter
of a turn clockwise.
7. Pull the bulb assembly out from the lamp housing.

6-37
8. Unhook the electrical connector by lifting up the
gray tabs and separate the connector from the
bulb base.9. Install the new bulb into the electrical connector.
Push the bulb firmly enough so that the gray tabs
hook over the tab on the bulb.
10. Carefully put the bulb assembly back into the lamp
housing and turn the bulb socket one
-quarter of a
turn counterclockwise.
11. Align the retaining clips on the back of the
headlamp with the rectangular holes in the
mounting panel.
12. Push firmly on both ends of the headlamp to snap it
into position.
13. Push the retaining clip down to its original position.
14. Reinstall the wing stud.

6-39
6. Turn the bulb socket one-quarter of a turn
counterclockwise.
7. Pull the bulb assembly out from the lamp housing.
8. Pull the bulb out of the base.
9. Install the new bulb into the electrical connector.
Push the bulb firmly enough so that the tabs hook
over the tab on the bulb.
10. Carefully put the bulb assembly back into the lamp
housing and turn the bulb socket one
-quarter of a
turn clockwise.
11. Replace the applique on the liftgate.
12. Gently lift the liftgate.
13. Reinstall the seven wing nuts and the
four outboard nuts.
14. Reinstall the panel inside the liftgate by connecting
the tabs.
15. Close the liftgate.
Outboard Taillamps, Brake Lamps and
Turn Signals
1. Open the liftgate.
2. Remove the
two screws on
the inboard
taillamp panel.

6-40
3. Pull the lamp directly rearward from the vehicle.
4. Turn the bulb socket one
-quarter of a
turn counterclockwise.
5. Pull the bulb assembly out from the lamp housing.
6. Unhook the electrical connector by lifting up the
tabs and separate the connector from the bulb base.
7. Install the new bulb into the electrical connector.
Push the bulb firmly enough so that the tabs hook
over the tab on the bulb.
8. Carefully put the bulb assembly back into the lamp
housing and turn the bulb socket one
-quarter of a
turn clockwise.
9. Reinstall the lamp to its pocket by lining up
the mounting pin and pushing forward to set
the position.
10. Reinstall the screws removed in Step 2.
11. Close the liftgate.
Windshield Wiper Blade Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See ªWiper Blade
Checkº in the Index for more information.
Replacement blades come in different types and are
removed in different ways. For proper type and length,
see ªNormal Maintenance Replacement Partsº in
the Index.
Here's how to replace the windshield wiper blades:
1. Turn the wipers on to the lowest intermittent setting.
2. Turn off the ignition while the wipers are at the
outer positions of the wipe pattern. The blades are
more accessible for removal/replacement while in
this position.
3. Pull the windshield wiper arm away from
the windshield