2002 BUICK RANDEZVOUS ECU

5-34
Storing the Spare Tire and Tools
1. Lay the compact spare tire on the ground at the
rear of the vehicle. Position the compact spare tire
so that the valve stem is pointed down facing the rear
of the vehicle.
2. Lower the cable to the ground. See ªRemoving
the Spare Tire (Vehicles without the Rear
Convenience/Cargo Tray)º or ªRemoving the Spare
Tire (Vehicles with the Rear Convenience/Cargo
Tray)º in the Index.
3. Tilt the retainer downward and slip it through the
center hole of the spare tire.
Make sure the retainer is fully seated across the
underside of the wheel.
4. Attach the folding wrench to the hoist shaft.5. Turn the folding wrench clockwise to lift the
spare tire.
6. When the tire reaches the stabilizer bar, move the
tire over the bar, then continue to turn the folding
wrench clockwise to lift the spare tire.
7. When the tire is almost in the stored position,
turn the tire so that the valve stem is towards the
rear of the vehicle.
This will help when you check and maintain tire
pressure in the spare.
8. Raise the tire fully against the underside of the
vehicle. Continue turning the folding wrench until
you feel more than two clicks. This indicates that the
compact spare tire is secure and the cable is tight.
The spare tire hoist cannot be overtightened.

5-35
9. Make sure the tire is stored securely. Push, pull, and
then try to rotate or turn the tire. If the tire moves,
use the folding wrench to tighten the cable.Put back all tools as they were stored in the jack storage
compartment and put the compartment cover back on.
To put the cover back on, slip the tabs on the side of
the cover into the cover opening. Push the cover in place
and push down the tabs on the cover so that it rests
in the groove. This secures the cover in place.
When you replace the compact spare with a full
-size
tire, reinstall the bolt
-on wheel covers or the center cap
(if equipped). Tighten them ªhand tightº over the wheel
nuts, using the folding wrench.

5-36
Storing the Flat Tire (Vehicles without the Stowable
Seat and without the Rear Convenience/Cargo Tray)
A. D-Ring
B. Wing Nut
C. J
-HookD. Valve Stem
E. Full
-Size Tire1. Flip up the D
-ring located in the rear cargo area.
2. Lay the tire in the rear cargo area of the vehicle with
the valve stem up with the center hole of the tire over
the D
-ring.
For vehicles with aluminum wheels, remove the
center trim cap by tapping the back of the cap with
the folding wrench.
3. Remove the J
-hook and the wing nut from the back
of the jack access door. Assemble the wing nut and
the J
-hook.
4. Install the wing nut and the J
-hook to the D-ring
through the center hole of the tire.
5. Tighten the wing nut to secure the tire to the floor.
Push and pull on the tire to make sure the tire is
secure and does not move.
6. Put back all tools as they were stored in the jack
storage compartment and put the compartment
cover back on.
To put the cover back on, slip the tabs on the side of the
cover into the cover opening. Push the cover in place
and push down the tabs on the cover so that it rests in
the groove. This secures the cover in place.

5-37
Storing the Flat Tire (Vehicles with the Rear
Convenience/Cargo Tray) (Option)
A. D-Ring
B. Rear Convenience/
Cargo Tray
C. Wing Nut
D. J
-HookE. Full
-Size Tire
F. Cap on Bottom
of Storage
Compartment1. Open the center storage compartment door of the
rear convenience/cargo tray.
2. Remove the cap on the bottom of the storage
compartment and flip the D
-ring up.
3. Lay the tire on top of the center storage compartment
with the valve stem down. Make sure you can see the
D
-ring through the center hole of the tire.
4. Remove the J
-hook and the wing nut from the back
of the jack access door. Assemble the wing nut and
the J
-hook.
5. Install the wing nut and the J
-hook to the D-ring
through the center hole of the tire.
6. Tighten the wing nut to secure the tire to the floor.
Push and pull on the tire to make sure the tire is
secure and does not move.
7. Put back all tools as they were stored in the jack
storage compartment and put the compartment cover
back on.
To put the cover back on, slip the tabs on the side of the
cover into the cover opening. Push the cover in place
and push down the tabs on the cover so that it rests in
the groove. This secures the cover in place.

5-38
Storing the Flat Tire (Vehicles with the
Stowable Seat) (Option)
A. Rear Convenience/
Cargo Tray
B. Full
-Size Tire
C. D
-RingD. Stowable Seat Strap
E. Cargo Net Hook
F. J
-Hook
G. Wing Nut1. If the seatback is not in an upright position, move it
to an upright position.
2. There is a strap attached to each side of the stowable
seat. Hook the straps to the cargo net hook in the
rear of the vehicle.
3. Flip the D
-ring so it is pointing outward.
4. Open the convenience/cargo tray cover.
5. Stand the full
-size tire up, in the tray against the
back of the seat with the valve stem pointing out.
6. Remove the J
-hook and the wing nut from the back
of the jack access door. Assemble the wing nut and
the J
-hook.
7. Install the wing nut and the J
-hook to the D-ring
through the center hole of the tire.
8. Tighten the wing nut to secure the tire to the seatback.
Push and pull on the tire to make sure the tire
is secure and does not move.
9. Put back all tools as they were stored in the jack
storage compartment and put the compartment
cover back on.
To put the cover back on, slip the tabs on the side of the
cover into the cover opening. Push the cover in place
and push down the tabs on the cover so that it rests in
the groove. This secures the cover in place.

5-39
Storing the Flat Tire with the Stowable Seatback
Folded Flat
A. Stowable Seatback
B. Full
-Size Tire
C. Wing NutD. J
-Hook
E. D
-Ring1. Fold the seatback down and flip the D
-ring up.
2. Lay the tire on the seatback with the valve stem
pointing up with the center hole of the tire over
the D
-ring.
3. Remove the J
-hook and the wing nut from the back
of the jack access door. Assemble the wing nut and
the J
-hook.
4. Install the wing nut and the J
-hook to the D-ring
through the center hole of the tire.
5. Tighten the wing nut to secure the tire to
the seatback.
Push and pull on the tire to make sure the tire
is secure and does not move.
6. Put back all tools as they were stored in the jack
storage compartment and put the compartment
cover back on.
To put the cover back on, slip the tabs on the side of the
cover into the cover opening. Push the cover in place
and push down the tabs on the cover so that it rests in
the groove. This secures the cover in place.

6-16
Engine Air Cleaner/Filter
The engine air cleaner/filter is located at the front of the
engine compartment on the driver's side of the vehicle,
under the engine coolant reservoir.
See ªEngine Compartment Overviewº in the Index for
more information on location.Checking or Replacing the Engine Air Cleaner/Filter
1. Remove the two clamps on the duct.
2. Remove the duct.
3. Unlatch the two hooks on top of the engine air
cleaner/filter housing.
4. Remove and replace the engine air cleaner/filter.
5. Align the tabs located on the bottom of the panel
with the slots at the top of the housing.
6. Latch the hooks to secure the panel in place. If the
panel moves easily, check that the tabs are seated
correctly in the slots.
7. Put the duct back on and reinstall the clamps.

6-41
4. Pull up the release clip, located at the connecting
point of the blade and the arm. Then, pull the blade
assembly down toward the glass to remove it from
the wiper arm.
5. Push the new wiper blade securely on the wiper arm
until you hear the release clip ªclickº into place.
6. Push the release clip, from Step 4, down to secure
the wiper blade into place.To replace the backglass mounted wiper blade, do
the following:
1. Turn the rear wiper off.
2. Pull the wiper away from the backglass.
3. Pull up the release clip, located at the connecting
point of the blade and the arm. Then, pull the blade
assembly down toward the glass to remove it from
the wiper arm.
4. Push the new wiper blade securely on the wiper arm
until you hear the release clip ªclickº into place.
5. Push the release clip, from Step 3, down to secure
the wiper blade into place.