2002 BUICK LESABRE tow

2-51 Electrochromic Day/Night Rearview Mirror
with Compass (If Equipped)
Your vehicle may have an electrochromic inside
rearview mirror with a compass. Your vehicle's mirror
may also contain OnStar

controls.
This is the on/off button for mirrors equipped with
OnStar controls.
Pressing the MIRROR button located at the bottom of
the mirror (or the on/off button for mirrors equipped
with OnStar controls), turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on,
the compass automatically calibrates as the vehicle
is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause the
liquid cleaner to enter the mirror housing.
Mirror Operation
To turn on the automatic dimming feature, press
the MIRROR button located at the bottom of the
mirror (or press and hold the on/off button for aboutthree seconds for mirrors equipped with OnStar controls).
To turn off automatic dimming, press MIRROR (or press
and hold the on/off button for about three seconds for
mirrors equipped with OnStar controls) again. The green
indicator light will be illuminated when this feature is
active. The automatic dimming feature will be active each
time the vehicle is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors
equipped with OnStar controls) once to turn the
compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the compass heading.
Compass Calibration
If, after two seconds, the display does not show a
compass heading (N for North, for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. If the letter C should ever appear in the compass
window, the compass may need calibration.

2-56
To use a lighter, push the center all the way in and let
it go. When it is ready, the center will pop back out by
itself. Pull out the entire unit to use it.
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
The cigarette lighter will only operate when the ignition
key is in RUN and for 10 minutes after turning the
ignition off. If you would like the lighter to operate
regardless of ignition position, and for extended periods
of time, see ªEngine Compartment Fuse Blockº in the
Index or see your dealer.
Sun Visors
Illuminated Visor Vanity Mirrors
When you open the cover to either the passenger's or
driver's visor vanity mirror, the lamps will turn on. The
brightness of the lamp can be adjusted by sliding the
switch up or down.
Dual Sun Visors
Each sun visor has two parts, so that both the windshield
and door glass can be shaded at the same time. To use
the dual sun visors, flip the first visor down and turn it
toward the window. Then, flip the second visor down
toward the windshield.
Auxiliary Power Outlets
The auxiliary power outlets can be used to plug in
electrical equipment such as a cellular telephone or
CB radio.
Your vehicle may have up to three power outlets
depending on the type of front seat you have. If your
vehicle has front bucket seats with a center console, you
will find two outlets inside the rear storage compartment.
(An extra power outlet can be found in the ashtray.)

2-61
Sunroof (Option)
The sunroof has both manual and express features for
opening the glass panel and sunshade.
If your vehicle has this
option, the switch for
the sunroof is located
on the headliner between
the sun visors.
The sunroof has four positions, express open, comfort
stop, closed and vent. The switch will only work when
the ignition is on or when RAP is active. See ªRetained
Accessory Power (RAP)º in the Index.Press and hold the switch rearward to the first position
to open the glass panel and sunshade. The sunshade can
also be opened manually.
Press and release the switch rearward to the second
position to express open the glass panel to the comfort
stop position. The comfort stop position is designed
to help reduce noise and make passengers more
comfortable. When the glass panel is express opening,
pressing the switch in any direction will stop it in a
partially
-opened position. The glass panel may be fully
opened by pressing the switch rearward again. If you
press and hold the switch in the express open position
for more than one and a half seconds, the express open
operation will be overridden and the sunroof will
operate manually.
To close the glass panel, press and hold the switch
forward. As the glass panel reaches the closed position,
it will open slightly toward the vent position and then
drop down to the closed position to provide a better seal.
The sunshade must be closed manually.
Once the sunroof is closed, it can be opened to the vent
position by pushing the switch upward. To close the
glass panel, pull the switch downward. The sunshade
must be opened and closed manually for vent operation.

2-74
If the light comes on while you are driving, pull off the
road and stop carefully. You may notice that the pedal is
harder to push. Or, the pedal may go closer to the floor.
It may take longer to stop. If the light is still on, have the
vehicle towed for service. See ªTowing Your Vehicleº in
the Index.
CAUTION:
Your brake system may not be working properly
if the brake system warning light is on. Driving
with the brake system warning light on can lead
to an accident. If the light is still on after you've
pulled off the road and stopped carefully, have
the vehicle towed for service.
When the ignition is on, the brake system warning light
will also come on when you set your parking brake. The
light will stay on if your parking brake doesn't release
fully. If you try to drive off with the parking brake set,
a chime will also come on until you release the parking
brake. If the light stays on after your parking brake is
fully released, it means you have a brake problem.
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when your engine
is started and may stay
on for several seconds.
That's normal.
If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN.
If the light doesn't come on then, have it fixed so it
will be ready to warn you if there is a problem.

2-77
NOTICE:
If you keep driving your vehicle with this light
on, after a while, your emission controls may not
work as well, your fuel economy may not be as
good and your engine may not run as smoothly.
This could lead to costly repairs that may not be
covered by your warranty.
NOTICE:
Modifications made to the engine, transaxle,
exhaust, intake or fuel system of your vehicle or
the replacement of the original tires with other
than those of the same Tire Performance Criteria
(TPC) can affect your vehicle's emission controls
and may cause the SERVICE ENGINE SOON
light to come on. Modifications to these systems
could lead to costly repairs not covered by your
warranty. This may also result in a failure to pass
a required Emission Inspection/Maintenance test.
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running. If the light doesn't come on, have it repaired.
This light will also come on during a malfunction in one
of two ways:

Light Flashing
-- A misfire condition has been
detected. A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service may be required.

Light On Steady
-- An emission control system
malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.
If the Light Is Flashing
The following may prevent more serious damage to
your vehicle:

Reducing vehicle speed.

Avoiding hard accelerations.

Avoiding steep uphill grades.

If you are towing a trailer, reduce the amount
of cargo being hauled as soon as it is possible.

3-3
VENT: This setting directs outside air through the
instrument panel outlets. The air conditioning
compressor is not working when VENT is selected. If
you select VENT while in FRONT defrost, the VENT
light will flash three times to let you know this is not
allowed. This is to prevent fogging.
HTR (Heater): This setting directs most of the air
out of the floor ducts while some air will flow through
the windshield and side window outlets. The air
conditioning compressor is not working when
HTR is selected.
BLEND: When BLEND is selected, the airflow will be
split between the windshield outlets and the floor ducts.
The air conditioning compressor will be operating.
FRONT: This setting directs most of the airflow
toward the windshield.
OFF: The ventilation system always allows fresh air to
flow through your vehicle when it is moving. The
system will try to keep the air at a previously chosen
temperature. When the system is off, the blower fan is
also off.MAX (Maximum Air Conditioning): This setting
directs airflow through the instrument panel outlets. The
amount of outside air entering your vehicle is limited
with this setting. The air conditioning compressor is on
in this mode.
Also in this mode, the RECIRC function is activated
to create the maximum cooling effect in the vehicle. If
RECIRC was active before selecting MAX, the light in
the RECIRC button will go off. If RECIRC is selected
after MAX, the light in the RECIRC button will not
come on.
NORM (Normal): This setting cools the outside
air entering your vehicle and directs it through the
instrument panel outlets. The air conditioning
compressor is on in this mode.
BI
-LEV (Bi-Level): This setting directs warmer air
to the floor ducts and cooler air to the instrument panel
outlets. The air conditioning compressor is on in
this mode.

3-5
OFF: If the passenger comfort control is turned on, it
can be turned off by pressing the OFF button once.
Pressing the OFF button a second time will turn off the
main system. Turning off the main system causes the fan
to turn off and the airflow to be directed toward the
floor. The system will still try to keep the interior of the
vehicle at the previously chosen temperature setting.
The outside temperature will show on the display when
the system is off.
The ventilation system always allows fresh air to flow
through your vehicle when the vehicle is moving even
when the system is off.
VENT (Flow
-Through Ventilation): The VENT
button allows outside air to flow through your vehicle
without the air conditioning compressor working. To
turn off the VENT selection, push the VENT button
again. If you select VENT while in FRONT defrost, the
VENT light will flash three times to let you know this is
not allowed. This is to prevent fogging.RECIRC (Recirculation): When RECIRC is selected,
the system will limit the amount of outside air entering
your vehicle. This is helpful when you are trying to cool
the interior of the vehicle quickly or limit the amount of
outside air entering your vehicle. RECIRC and AUTO
may be selected at the same time. The system will remain
in RECIRC until the ignition is turned off or the RECIRC
button is pressed again. RECIRC can be selected in all
manual airflow modes except FRONT defrost and VENT.
If you select RECIRC while in FRONT defrost, the
RECIRC light will flash three times to let you know this is
not allowed. This is to prevent fogging. FRONT: This selection is used to defrost
the windshield by directing the airflow toward the
windshield. To turn off FRONT, press the AUTO
or AIR FLOW button.
If the AIR FLOW up button is selected while in the
FRONT defrost mode, the system will direct the air
toward the windshield and the floor. If the AIR FLOW
down button is selected while in the FRONT defrost
mode, the system will direct the air toward the floor, and
the FRONT defrost mode will cancel.
FRONT defrost will work better if any ice or snow is
cleared from the hood and the air inlet area between the
base of the windshield and the hood.

3-7
Sun and temperature sensors automatically adjust the air
temperature, the airflow direction and the fan speed to
maintain your temperature setting. The system may
supply cooler air to the side of the vehicle toward the
sun. Be careful not to put anything over the sensor on
top of the dash.
The display will show fan speed, temperature level
setting and airflow direction for a few seconds whenever
AUTO is selected, and then it will display the outside
temperature. The outside temperature reading is most
accurate when the vehicle is moving. During stops, the
display shows the previous temperature for best
accuracy and system control.
To find your preferred temperature setting, start with the
system in AUTO mode and the TEMP button adjusted
to 75
F (24
C), give the vehicle about 20 minutes to
stabilize, and adjust your temperature setting if
necessary, by using the TEMP button. The display will
show the temperature setting for a few seconds and then
it will display the outside temperature. If you want to
see your current automatic fan speed, airflow direction
and temperature setting, press the AUTO button.In cold weather, the system will delay turning on the fan,
to avoid blowing cold air. During this delay the system
will be in FRONT defrost mode and the light in the button
will come on and stay on as long as the display is showing
the current mode, set TEMP and FAN speed. This light
will go off when the display returns to the outside
temperature. The length of the delay depends on the
engine coolant temperature and the outside temperature.
Pushing the FAN, AIR FLOW or FRONT buttons will
override this delay, turn off the AUTO setting and return
the system to manual operation.
Personal Choice Comfort Controls
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for the temperature, fan speed
and the direction of the airflow.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each keyless
entry transmitter.
To recall comfort settings, press the unlock button on the
remote keyless entry transmitter and put the ignition in
ACCESSORY or RUN. The climate control setting last
chosen by the identified driver (1 or 2) will be recalled.