2002 Acura TL ignition

If the VSA indicator comes on while
driving, pull to the side of the road
when it is saf e and turn of f the
engine. Reset the system by
restarting the engine, and watch the
VSA system indicator. If the
indicator remains on, or comes back
on while driving, have the VSA
system inspected by your Acura
dealer.When VSA is off, the VSA Activation
Indicator light comes on as a
reminder. Pressing the switch again
turns the system back on.
If the indicator does not come on
when the ignition switch is turned
ON(II),theremaybeaproblem
with the VSA system. Have your
dealer inspect your car as soon as
possible.
Without VSA, your car will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
This switch is under the lef t vent.
Press it to turn the Vehicle Stability
Assist system on and of f .
The VSA system indicator (see page
) comes on and stays on when
there is a problem with the VSA
system. The VSA Activation
indicator will also come on. 61
CONT INUED
VSA Syst em Indicat orVSA Of f Switch
Vehicle Stability Assist (VSA) System
Driving197
V V
S
SAA S
SYYSSTTE
EM
M I
INND DI
ICCA A T
TO
OR R V
VS
SAA O
OFFFF S
SWWI ITT C
CH H
00/12/25 14:25:52 31S0K630_200

CONT INUED
Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap. Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard.
Install a rubber hose on the drain
bolt at the rear of the engine
cylinder block. Loosen the drain
bolt.
3.
1.
2. 4.5.
6.
Cooling Syst em
Maint enance231
D D
R
RAA I
INN P
PL
LUUG G R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
H
H O
OL LDD E
ER
R R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
D
D R
RAA I
INN B
BOOL LTT
00/12/25 14:31:26 31S0K630_234

Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
Clean up any dirt and oil that have
collected around the ignition coils.
The spark plugs in your car are a
special platinum-tipped design f or
longer lif e. The spark plugs should
be replaced according to the time
and distance recommendations in
the maintenance schedule.
1.
2.3.
Replacement
Spark Plugs
Maint enance240
H H
O
OL LDD I
INNG G
C
CL LIIPP L
LO
OC CKK T
TA
A B
B
00/12/25 14:33:01 31S0K630_243

Put the new spark plug into the
socket; then screw it into the hole.
Screw it in by hand so you do not
crossthread it.Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque:
Use a wrench to remove the
hexagonsocketheadcapbolt
holding the ignition coil. Remove
the ignition coil by pulling it
straight out.
Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket.
4.
5.
6. 7.
CONT INUED
Spark Plugs
Maint enance241
H H
E
EX
X A
AG
GO ONN S
SOOC CKKEET
T H
HE
EA
A D
D C
CAA P
P B
BOOL LTT
13 lbf·ft (18 N·m , 1.8 kgf·m)
00/12/25 14:33:11 31S0K630_244

´
µ
´
µ
Push the wire connector onto the
ignition coil. Make sure it locks in
place. Install the ignition coil. Reinstall
the hexagon socket head cap bolt. Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.
Spark Plug Gap: Spark Plug Gap:NGK:
DENSO:
8. 11.
10.
9. NGK:
DENSO:
Specif ications:
Spark Plugs
Maint enance
Type S
Premium model
242
0.04 in (1.1 mm)
PKJ20CR-M11 PZFR6E-11
0.04 in (1.1 mm) PKJ16CR-L11
PZFR5F-11
0
0.1 mm
0
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.
00/12/25 14:33:22 31S0K630_245

If your car’s battery is disconnected
or goes dead, the audio system will
disableitself.Thenexttimeyouturn
on the radio you will see ‘‘Code’’ in
the f requency display. Use the
Preset buttons to enter the five-digit
code (see page ).If your car’s battery is disconnected
or goes dead, all stored driving
positions will be lost. To store the
driving positions again, see the
storingprocedureonpage .
The Navigation System will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Ref er to the
Navigation System Owner’s Manual.
151
96
Cars with Navigation System
Battery
Maint enance245
Charging the battery with the cables
connected can seriously damage your
car’s electronic controls. Detach the
battery cables bef ore connecting the
battery to a charger.
00/12/25 14:33:43 31S0K630_248

µ
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or they leave streaks
and unwiped areas when used.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
To replace the blade:
Raise the wiper arm of f the
windshield. Turn the ignition ON (II), switch
the wipers to INT or (low
position), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel.
2. 1. 3.
Wiper Blades
Maint enance246
W WI
IPP E
ER
R A
AR
RMM S
S
L
LOOC CKK T
TA
A B
B
00/12/25 14:33:52 31S0K630_249

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Lower the wiper arm down against
the windshield. Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Turn the ignition switch ON (II)
and return the windshield wipers
to their park position.
4. 5. 6.
7.
8.
9.
Wiper Blades
Maint enance247
R RE EI
INNF FOOR RCCEEM
M E
EN
NT T
B
BL
LAA D
DE
E B
BLLAA D
DE
E
00/12/25 14:34:02 31S0K630_250