2002 Acura RL radiator

Î
These labels are in the locations
shown. They warn you of potential
hazards that could cause serious
injury. Read these labels caref ully.
If a label comes of f or becomes hard
to read, contact your Acura dealer
f or a replacement.
U.S. models onlyU.S. models Canadian models
Driver and Passenger Saf ety
Saf ety L abels
50
RADIATOR CAP
SUN VISOR
HOOD DASHBOARD The U.S. car model
01/09/28 19:33:16 31SZ3660_053

Refer toon page f or inf ormation
on checking other items in your
Acura. Look at the coolant level in the
radiator reserve tank. Make sure it is
between the MAX and MIN lines. If
it is below the MIN line, see on page f or
informationonaddingtheproper
coolant.
Remove the dipstick again and
check the level. It should be
between the upper and lower
marks.
If it is near or below the lower mark,
see on page .
Insert it all the way back in its tube. 4.
3.
227231
225
Service Station Procedures
Bef ore Driving
Owner Maintenance
Checks A dding
Engine Coolant
A dding Oil
Engine Coolant Check
182
M M I
INN
M
M
A
AX
X
L
LO OW WE ER
R M
M A
AR
RKK
U
UP
PP
PE
ER
R M
M A
AR
RKK R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
01/09/28 19:55:22 31SZ3660_185

µµµ µ
µ
µ
µ
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the page given.
Engine oil level Check every
time you fill the fuel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
youfillthefueltank.Seepage .
Windshield washer f luid Check
the level in the reservoir monthly.
If weather conditions cause you to
use the washers f requently, check
the reservoir each time you stop
f or f uel. See page .Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See
page . Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page
.
Automatic transmission Check
the f luid level monthly. See page .
Brakes Check the f luid level
monthly. See page . 181
182
237
238 240 255
260
Owner Maintenance Checks
Maint enance225
01/09/28 20:02:19 31SZ3660_228

If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
The coolant you add should always
be a mixture of 50 percent antif reeze
and 50 percent water. Never add
straight antif reeze or plain water.If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
Make sure the engine and radiator
are cool.
Always use Honda All Season
Antif reeze/Coolant Type 2. This
coolant is pre-mixed with 50 percent
antif reeze and 50 percent water. It
does not require any additional
mixing.
If it is not available, you may use
another major-brand non-silicate
coolant as a temporary replacement.
Make sure it is a high-quality coolant
recommended f or aluminum engines.
However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling
system to malf unction or f ail. Have
the cooling system f lushed and
ref illed with Honda antif reeze/
coolant as soon as possible.
1.
CONT INUED
A dding Engine Coolant
Cooling Syst em
Maint enance231
R RE
ES
SE ER
RV V E
E T
TA
A N
NK K
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
01/09/28 20:03:12 31SZ3660_234

Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank. Put the radiator cap back on.
Tighten it f ully. The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Remove the radiator cap by
pushing down and turning
counterclockwise. Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system. Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.
2.
3. 4.
5.
6.
Cooling Syst em
Maint enance232
R RE
ES
SE ER
RV V E
E T
TA
A N
NK K
R
RA
A D
DI
IAA T
TO
OR R C
CAA P
P
01/09/28 20:03:22 31SZ3660_235

Loosen the drain plug on the
bottom of the radiator. The
coolant will come out through the
hole in the splash cover.
Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2. Use of any non-
Honda coolant or plain water can
result in corrosion and deposits in
the cooling system.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
1.
2.3.
CONT INUED
Replacing Engine Coolant
Cooling Syst em
Maint enance233
D D
R
RAA I
INN P
PL
LUUG G
01/09/28 20:03:32 31SZ3660_236

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Put the drain cap back in place
tightly, then reinstall the clip on
the drain cap securely.
On the right side of the engine
block, remove the clip with a plier,
andthenremovethedraincap. 5.
4. 6.
Cooling Syst em
Maint enance234
C CL
LIIPP
D
D R
RAA I
INN C
CAA P
P
R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K H
HO
OL LDD E
ER
R
01/09/28 20:03:39 31SZ3660_237

Remove the two bolts and the
three nuts with a 7/16 in (10 mm)
wrench, then remove the engine
cover.Loosen the bleeder bolt on top of
the engine.Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
The cooling system capacity is:
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
7. 8. 9.
10.
CONT INUED
Cooling Syst em
Maint enance235
B BO OL LTT S
S B
BL
LEE E
ED
D E
ER
R B
BOOL LTT
N
NU
UTTS
S
1.61 US gal (6.1, 1.34 Imp gal)
01/09/28 20:03:50 31SZ3660_238