2002 Acura CL ignition

If you f orget and leave the key in the
ignition switch, Lockout Prevention
will not allow you to lock the driver’s
door. With the driver’s door open
andthekeyintheignition,both
master door lock switches are
disabled. However, if the driver’s
door is not open, the master door
lock switches are not disabled.
Pushing the switch down on the
open passenger’s door will lock both
doors. If you try to lock an open
driver’s door by pushing down the
lock tab, the tabs on both doors pop
up. Pushing down the lock tab on the
passenger’s door only locks that door.You can lock and unlock your car
with the remote transmitter. When
you push the LOCK button, both
doors lock. The parking lights, side
marker lights, taillights and license
plate light will f lash once.When you push the LOCK button a
second time within 5 seconds after
you have locked the doors, you will
hear a beep to verify that the doors
are locked and the security system
has set.
When you push the UNLOCK button
once, only the driver’s door unlocks.
The passenger’s door unlocks when
you push the button a second time.
The parking lights, side marker
lights, taillights and license plate
light f lash twice each time you push
the button.
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
either door, the light stays on f or
about 10 seconds, then f ades out. If
you relock the doors with the remote
transmitter before 10 seconds have
elapsed, the light will go of f
immediately.
Remote Transmitter
L ockout Prevent ion
Keys and Locks
Inst rument s and Cont rols78
L LE
E D
D
U
UN NLLOOC CKK
B
BU UT TT
TO
ON N L
LO
OC CKK
B
BU UT TT
TO
ON N
T
T R
RU UN NKK
R
RE EL
LEE A
A S
SEE
B
BU UT TT
TO
ON N
P
P A
A N
NI ICC
B
BU UT TT
TO
ON N

CONT INUED
If the seat and mirrors are already in
the proper positions, you will hear
three beeps when you open the door.
Theremotetransmitterswillalso
activate the Driving Position
Memory System (see page ).
When you open the driver’s door
after unlocking it with the remote
transmitter, you will hear a beep.
The driver’s seat and outside mirrors
move to the positions stored in that
memory location. You will hear two
beeps when the movement is
complete. The driving position memory
activated (Memory 1, Memory 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in the
memory that is activated by the
transmitter you normally carry.
You can turn of f this driving position
memory activation. While standing
near the car, press and hold the
LOCK and UNLOCK buttons at the
same time. The LED in the remote
transmitter will blink twice. Then
release the buttons.
To turn it back on, repeat this
procedure. The LED will come on
f or one second to indicate the
f eature has been turned on.
If you unlock the doors with the
remote transmitter, but do not open
either door within 30 seconds, the
doors automatically relock and the
security system sets.
You cannot lock the doors with the
remote transmitter if either door is
not f ully closed or the key is in the
ignition switch. You cannot unlock
the doors with the key in the ignition
switch.
To open the trunk, push the Trunk
Release button f or approximately
one second.
You can open the trunk with the
remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch.
95
Keys and Locks
Inst rument s and Cont rols
Recalling a Memorized Driving
Position
79
W Wi itth h M
M e
emm o
or
ryy 1
1 W
Wi
itth h M
M e
emm o
or
ryy 2
2

´
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
Battery type: CR2025To replace the battery, remove the
round cover on the back of the trans-
mitter by turning it counterclockwise
with a coin.
Remove the old battery and note the
polarity. Make sure the polarity of
the new battery is the same ( side
f acing up), then insert it in the
transmitter.
When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will not light. Replace the
battery as soon as possible.
Keys and Locks
Inst rument s and Cont rols
Panic Mode
Replacing t he Bat t ery
80
C Clloo s
see
O
Op
pe
enn R
RO
OU UNNDD
C
CO OV VE
ER
R
B
BA A T
TT
TE
ER
RY Y

µ
Pull up or push down on the f ront of
the switch to move the seat bottom’s
f ront edge up or down. Pull up or
push down on the rear of the switch
to move the rear of the seat bottom
up or down.
Push the horizontal switch forward
or backward to move the seat
forward or backward. The long horizontal switch adjusts
the seat bottom in several directions.
The short vertical switch adjusts the
seat-back angle.
Make all seat adjustments bef ore
you start driving.
Your Acura has power adjustable
driver’s seat. The two power seat
adjustment switches are on the
outside edge of the seat bottom. The
f ront passenger’s seat is also power-
adjustable.
You can adjust the power seats with
the ignition switch in any position.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 1413Driver’s Seat Adjustments
Seat A djustments
Inst rument s and Cont rols86

µ
The seat adjustment switches are on
the outside edge of the seat bottom.
Push the long horizontal switch
forward or backward to move the
seat bottom in that direction.
Adjust the seat-back angle by
pushing the vertical switch in the
direction you want to move.
Make all seat adjustments bef ore
you start driving.
Vary the lumbar support by moving
the lever on the right side of the
seat-back. Move the lever forward or
backward to adjust the lumbar
support through its f ull range. You can adjust the seat with the
ignition switch in any position.
See pages f or important saf ety
inf ormation and warnings about how toproperly position seats and seat-backs. 13
14
Driver’s L umbar Support Front Passenger’s Seat
Adjustments
Seat A djustments
Inst rument s and Cont rols88

Turn the ignition switch ON (II).
Move the selector switch to L
(driver’s side) or R (passenger’s
side).
Keeptheinsideandoutsidemirrors
clean and adjusted f or best visibility.
Be sure to adjust the mirrors bef ore
you start driving.
The inside mirror can automatically
darken to reduce glare. To turn on
this feature, press the button on the
bottom of the mirror. The AUTO
indicator comes on as a reminder.
When it is on, the mirror darkens
when it senses the headlights of a
vehicle behind you, then returns to
normal visibility when the lights are
gone. Press the button again to turn
of f this sensing.Adjust the outside mirrors with the
adjustment switch on the driver’s
door armrest:
1.
2.
CONT INUED
Adjusting the Power Mirrors
Mirrors
Inst rument s and Cont rols93
S SE
EN
NS SOOR R
I
INND DI
ICCA A T
TO
OR R S
SE
EL
LEE C
CT TO
OR R S
SWWI ITT C
CH H
A
A U
UT TO
O B
BUUT TT
TO
ON N

The outside mirrors are heated to re-
move fog and frost. With the ignition
switchON(II),turnontheheaters
by pressing the button. The light in
the button comes on as a reminder.
Press the button again to turn the
heaters of f .
Push the appropriate edge of the
adjustment switch to move the
mirrorright,left,up,ordown. When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.
Outside mirror positions can be
stored in the driving position
memory system (see page ). With the selector switch in the
center (of f ) position, the passenger’s
side mirror will pivot downward
slightly when you shif t the
transmission into reverse. This will
give you a better view of that side of
the vehicle while parallel parking.
The mirror returns to its original
position when you take the
transmission out of reverse. 4.
3. 95
Mirrors
Inst rument s and Cont rols94
H HE
EA
A T
TE
ED
D M
MI
IRRR ROOR R B
BUUT TT
TO
ON N
A
A
D
DJ
JUUS STTM
M E
EN
NT T S
SWWI ITT C
CH H

Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Store a driving position as explained
in this section only when the car is
parked.
Your Acura has a memory f eature
f or the driver’s seat and outside
mirror positions.
Two seat and outside mirror
positions, f or dif f erent drivers or
drivingconditions,canbestoredin
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Memory1orMemory2).
Adjust the seat to a comfortable
position (see page ).Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
Adjust the outside mirrors f or best
visibility (see page ).
3.
1.
2.
86
93
CONT INUED
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols95
M M E
EM
M O
O B
BUUT TT
TO
ON N