2002.5 PEUGEOT 807 display

YOUR 807 IN DETAIL115
Maintenance position of front
windscreen wiper
This position allows the front wind
screen wiper blades to be removed.
In the minute following switching off
of the ignition, any action on the
stalk positions the wipers against the
windscreen uprights (for Winter
parking, cleaning of the windscreen
or replacing the blades).
To park the wipers after this has
been done, switch on the ignition
and operate the stalk.
Rear windscreen wiper
Turn ring
Ato the first notch.
The wiping speed is
inversely proportional to the
speed of the vehicle.
Automatic rear windscreen wiping
 place the front wipers stalk in a
position other than 0.
 engage reverse gear.
 the rear wiper operates with inter
mittent wiping.
Note: this function cannot be dis
armed if a bicycle carrier is fitted.
Therefore, you must fit a special bicy
cle carrier, approved by PEUGEOT,
or contact a PEUGEOT dealer.
Rear windscreen wash
Turn ring Apast the first
notch: the windscreen wash
then the windscreen wiper
operate for a specified time.
Do not cover the rain
sensor located at the bot
tom centre of the wind
screen.
When using an automatic car
wash, switch off the ignition or
check that the wiper control is not
in the automatic position.
In winter it is advisable to wait for
the windscreen to completely
clear of ice before operating the
automatic wipe. In winter, in the presence
of a considerable
amount of snow or ice,
switch on the rear screen
demister. Once deicing
is complete, remove the snow or
ice which has accumulated on the
rear wiper blade. You can now
operate the rear windscreen
wiper.
Automatic timed windscreen
wipers
The automatically timed wiping is
controlled by a rain sensor fitted on
the windscreen.
In the
AUTO position, the wind
screen wipers operate automatically
and adapt their speed to the inten
sity of the rainfall.
Operating check
Activation
When the function is activated, the
message "Automatic windscreen
wipers activated" appears on the
multi–function display.
18-11-2002

YOUR 807 IN DETAIL
116
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen CT
– the "vehicle" tab with:
• range, current consumption and the distance still to be driven,
– tab '1' (route '1') with:
• the distance driven and the aver age speed calculated over route
'1'
– tab '2' (route '2') with the same fea
tures.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
Monochrome screen B
the remaining range
the distance travelled
the average consumption
the current consumption
the average speed
In addition, it allows access to the
warning log information and to the
Excess speed warning function.
Zero reset
Press the stalk for more than two
seconds.
Colour screen DT
– the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
– 'Route 1' with:
• the distance travelled,
• the average coonsumption,
• the average speed,
– 'Route 2' with the same features.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
18-11-2002

Distance remaining to be
travelled
This is the distance remaining to the
destination. It can either be calculat
ed by the navigation if guidance is
activated, or entered by the user,
minus the distance covered since
the distance was entered.
Note:if digits are missing, dashes
are displayed in their place.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The warnings log
This summarises the active warning
messages by displaying them on the
multifunction display.
The excess speed warning
function *
This monitors the maximum speed
required. In the event that the pro
grammed speed is exceeded, the
message ''Speed too high'' appears
on the multifunction display, accom
panied by an audible signal.
Programming
Accelerate to the desired speed.
Keep pressing the control to store in
memory.
* During the year.
YOUR 807 IN DETAIL 117
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note:
this figure may increase if there
is a change in the style of driving or
the road surface, producing a signifi
cant drop in current consumption.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel
consumed during the last few sec
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero. Activation
Keep pressing the control until the
display indicates
''Excess speed
ON'' .
Switching off
Keep pressing the control until the
display indicates ''Excess speed
OFF'' .
The routes
The routes "1" and ''2''are indepen
dent but have identical application.
Route "1"for example allows you to
make daily calculations and route
"2" monthly calculations.
18-11-2002

YOUR 807 IN DETAIL
116
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the following
sequence of data is displayed:
Monochrome screen CT
– the "vehicle" tab with:
• range, current consumption and the distance still to be driven,
– tab '1' (route '1') with:
• the distance driven and the aver age speed calculated over route
'1'
– tab '2' (route '2') with the same fea
tures.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
Monochrome screen B
the remaining range
the distance travelled
the average consumption
the current consumption
the average speed
In addition, it allows access to the
warning log information and to the
Excess speed warning function.
Zero reset
Press the stalk for more than two
seconds.
Colour screen DT
– the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
– 'Route 1' with:
• the distance travelled,
• the average coonsumption,
• the average speed,
– 'Route 2' with the same features.
It also permits access to the Excess
Speed Warning function.
Zero reset
When the required route is dis
played, press the button for more
than two seconds.
18-11-2002

Distance remaining to be
travelled
This is the distance remaining to the
destination. It can either be calculat
ed by the navigation if guidance is
activated, or entered by the user,
minus the distance covered since
the distance was entered.
Note:if digits are missing, dashes
are displayed in their place.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The warnings log
This summarises the active warning
messages by displaying them on the
multifunction display.
The excess speed warning
function *
This monitors the maximum speed
required. In the event that the pro
grammed speed is exceeded, the
message ''Speed too high'' appears
on the multifunction display, accom
panied by an audible signal.
Programming
Accelerate to the desired speed.
Keep pressing the control to store in
memory.
* During the year.
YOUR 807 IN DETAIL 117
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note:
this figure may increase if there
is a change in the style of driving or
the road surface, producing a signifi
cant drop in current consumption.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel
consumed during the last few sec
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero. Activation
Keep pressing the control until the
display indicates
''Excess speed
ON'' .
Switching off
Keep pressing the control until the
display indicates ''Excess speed
OFF'' .
The routes
The routes "1" and ''2''are indepen
dent but have identical application.
Route "1"for example allows you to
make daily calculations and route
"2" monthly calculations.
18-11-2002

YOUR 807 IN DETAIL
118
Trip computer configuration
This function allows inputting of the
distance to the destination (when
guidance is not activated; otherwise
the information is given by the navi
gation) and also changing of the
units (°C or °F, km and litres or miles
and gallons).
Diagnostics
This function tells you the warnings,
the quantity of emergency fuel and
the GPS cover present at the time
consulted.
Note:
these warnings have previous
ly been displayed in the form of mes
sages and/or warning lights on the
control unit.
There are 6 categories of diagnostics :
engine diagnostics (warnings linked to the engine, gearbox
etc....),
brake diagnostics,
suspension diagnostics (warnings linked to the suspension, ESP
etc....),
wheel diagnostics (warnings linked to tyres),
door and window diagnostics,
passenger compartment diagnos tics. Distance to destination
When guidance is not activated, this
enables an approximate value to be
entered to make all the trip computer
calculations possible.
Specific features of the
monochrome screen CT and
the colour screen DT
General menu
Press the
"MENU"button to access
the general menu.
Select the icon ''Trip computer''
using the dial, then validate to
access the ''Trip computer'' menu.
The ''trip computer'' menu offers var
ious choices:
Trip computer configuration,
Diagnostics.
'Trip computer' context menu
The context menu associated with
the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli
cation currently being used in the
main screen window.
Briefly press the continuous applica
tion 'Trip computer' button to select
one of the following functions:
Warnings log,
Distance to destination.
18-11-2002

When this warning light
comes on, connected to the
STOPwarning light,
accompanied by a buzzer
and the message "Braking
fault" , it indicates that there is a mal
function of the electronic brake force
distribution, which can cause a loss of
control of the vehicle when braking.
Stop immediately.
In both cases, consult a Peugeot
dealer.
ANTILOCK BRAKING
SYSTEM (ABS) AND THE
ELECTRONIC BRAKE FORCE
DISTRIBUTION (EBFD)
The ABS, in conjunction with the elec
tronic brake force distribution, increas
es the stability and manoevrability of
your vehicle, particularly on poor or
slippery road surfaces.
Note: when changing wheels (tyres
and rims), make sure that these are
approved.
The antilock braking system comes
into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
a buzzer and the message
"ABS fault" , it indicates
that there is a malfunction
of the ABS, which can cause a loss
of control of the vehicle when brak
ing.
YOUR 807 IN DETAIL
128
To return to normal operation, pull
the lever upwards until a click is
heard.Illumination of this light,
accompanied by an audible
signal and the message
"handbrake on" on the
multi–function display, indi
cates that the handbrake is still on or
has not been properly released.
HANDBRAKE
Applying
When parking, pull the handbrake to
immobilize your vehicle.
Warning : when parking on a slope,
direct your wheels towards the pave
ment and pull the handbrake.
Releasing
Pull on the handle and press the but
ton to release the handbrake.
Disengaging
Apply the handbrake.
Pull the button located at the end of
the handbrake forwards.
The handbrake lever lowers.
You can now pivot the seat. EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system
enables the optimum braking pres
sure to be reached more quickly,
thus reducing the stopping distance.
It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in the
resistance of the pedal and an
increase in braking efficiency. Normal operation of the ABS may
make itself felt by slight vibrations
of the brake system.
In emergency braking, press
very firmly without releasing
the pressure.
18-11-2002

YOUR 807 IN DETAIL
132


: snow programme
P ark: to immobilise the vehicle or start the engine ,
with the handbrake on or off.
R everse: to reverse(select this function with the
vehicle stationary, engine at idle).
N eutral: to start the engine and to park, with the
handbrake on.
Note: if function Nis engaged inadvertently while
driving, allow the engine to return to idle before
engaging function Dto accelerate.
D rive: for drivingin automatic mode.
M anual: for drivingin manual mode.
Moving off
With the engine running, to move off
from position P:
 it is essential to press the
brake pedal to exit position P,
 select function R, D or M, then
gradually release the pressure
on the brake pedal; the vehicle
moves off immediately.
You can also move off from position N:
 release the handbrake, with your
foot on the brake
 select function R, D or M, then
gradually release the pressure
on the brake pedal; the vehicle
moves off immediately.
WARNING
When the engine is at idle, brakes not
applied, if function R, D or M is
selected the vehicle moves even with
out the accelerator being pressed.
For this reason, do not leave
children unsupervised inside the
vehicle, with the engine running .
When maintenance operations need
to be carried out with the engine
running, apply the handbrake and
select position P.
"PORSCHE TIPTRONIC SYSTEM" AUTOMATIC GEARBOX
The four speed
automatic gearbox offers a choice between the comfort of inte
gral automatic operation , enhanced by a snow programme, or the pleasure of
manual gear changing .
Gear selection gate  Move the lever in the gate to select a function.
Once the function is selected, the corresponding indicator lig ht appears on
the instrument panel display.
If the battery is flat and the lever is in position P, it will be impossible
to change to another position.
18-11-2002