2002.5 PEUGEOT 807 stop start

YOUR 807 IN DETAIL105
Make a careful note of the number on each key. The key number i s coded on the label attached to the key. If
the key is lost, your PEUGEOT dealer can rapidly supply you with ne w keys.
The highfrequency remote control is a sensitive system; do not ope rate it while it is in your pocket as there is
a possibility that it may unlock your vehicle without your knowle dge.
The remote control cannot operate if the key is in the ignit ion, even if the ignition is switched off, except for reprogramming.
Do not operate the deadlock if there is someone inside the vehicle.
Driving with the doors locked or deadlocked may mean it is diffi cult for the emergency services to access the
passenge rcompartment in the event of an emergency.
As a safety measure (when there are children on board), remove the i gnition key when leaving the vehicle, even for a
short time.
Do not handle the buttons of your remote control when out of range of your vehicle, as you run the risk of stopping it
from working.
It would then be necessary to reprogramme the remote control.
When buying a secondhand car:
– Ensure that you are given the confidential card;
– have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
that can start your vehicle.
Do not make any modifications to the electronic engine immobil iser system.
18-11-2002

AUTOMATIC SWITCHING ON
OF LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off when the light
becomes bright enough or the wind
screen wipers stop.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. As a consequence, the lights
will not come on automatically.
This function is active when the
vehicle is supplied to the customer.
To disarm or activate the function :  Start with the key in the acces
sories position (1st notch),
 Place the lights stalk in position 0,
 Press the end of the stalk for more
than two seconds.
Note: after the ignition is switched off
and depending on the brightness,
the lights remain on for approximate
ly 45 seconds or until the vehicle is
locked.
Do not cover the brightness sen
sor located in the centre of the
fascia. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting
active" on the multi–function dis
play .
Disarming
Disarming of the function is accom
panied by an audible signal.
Note: the function is disarmed
temporarily when the driver uses the
manual lighting controls.
YOUR 807 IN DETAIL 113
18-11-2002

YOUR 807 IN DETAIL
114
WINDSCREEN WIPER STALK
Front windscreen wiper stalk with
intermittent wipe
2 Fast wipe
(heavy rain).
1 Normal wipe
(moderate rain).
l Intermittent wipe.
0 Off.
Single wipe
(press downwards). Front windscreen wiper stalk with
automatic wipe
2 Fast wipe
(heavy rain).
1 Normal wipe
(moderate rain).
AUTO Automatic wipe.
0 Off.
Single wipe
(press downwards). Operation
In position
1or 2, when the vehicle
stops, the windscreen wiper
changes to a lower wiping speed,
then resumes its initial speed when
the vehicle starts again.
In the Intermittent position, the wip
ing speed is proportional to the
speed of the vehicle.
In the AUTOposition, the wiping
speed is proportional to the heavi
ness of the rain.
When the ignition has been
switched off for more than one
minute with the stalk in the wipe
position, it is necesary to reacti
vate this function. To do this, move
the stalk to any position, then move
it back to the required position.
Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you.
The windscreen wash then the wind
screen wipers operate for a fixed
period.
The windscreen wash and headlamp
wash operate simultaneously for a
few seconds, only if the dipped
beam or main beam headlamps
are on.
18-11-2002

PRACTICAL INFORMATION
152
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position Less than a minute after switching
off the ignition, operate the wipers
stalk to position the wiper blades
along the windscreen uprights
(maintenance position).
Changing a front wiper blade  Lift the wiper arm, then disconnect
the windscreenwash pipe.
 Unclip the blade and remove it.
 Fit the new blade.
 Reconnect the windscreenwash
pipe and push back the wiper arm.
To return the windscreen wipers
to their normal position, switch on
the ignition and operate the
wipers stalk.
Changing the rear wiper blade  Lift the wiper arm, then unclip the
blade and remove it.
 Fit the new blade and push back
the wiper arm. ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (windscreen wiper, electric
windows, sunroof, courtesy lights,
audio equipment etc.) can only be
used for thirty minutes, to prevent
discharging the battery.
After thirty minutes, the message
"Economy mode active"
appears
on the multifunction display and the
active functions are put on standby.
To resume use of these functions,
start the engine and let it run for a
few seconds.
Aflat battery will pre
vent the engine from
starting.
18-11-2002