2002.5 PEUGEOT 807 display

INSTRUMENTS AND CONTROLS
32
In zoneA,the temperature is correct.
In zone B, the temperature is too high. The central STOPwarning light and the
maximum coolant temperature warning light 1come on, accompanied by an
audible signal and the message "Coolant temp. too high"on the multifunction
display.
You must stop immediately.
Warning : wait for the engine to cool before topping up the le vel.
The cooling system is pressurised.
In the event of a breakdown and in order to avoid any risk of scalding, unscrew
the cap two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Instrument panel with
monochrome screen
Instrument panel with colour
screen
Coolant temperature indicator light
18-11-2002

Maximum
Minimum
Check the level with
the dipstick and top it
up.
The figure shown is
only correct if the vehicle has been
on stable, level ground, with the
engine stopped, for 10 minutes.
No oil
The message "Top
up the oil" appears
on the multifunction
display, accompa
nied by an audible signal.
It is essential to top up the oil to the
correct level, otherwise the engine
may be damaged.
Oil gauge fault
Flashing of the seg
ments indicates a
fault.
Check the level
using the dipstick.
Consult a PEUGEOT dealer. Control module display
After switching on the ignition, three
functions are shown in succession:
– service indicator (see correspond ing section),
– engine oil level indicator,
– total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for thirty seconds, when
the ignition is switched off, on open
ing the driver's door as well as on
locking and unlocking the vehicle.
It also displays the automatic gear
box positions and programmes
selected (see corresponding sec
tion).
Engine oil level
When the ignition is switched on, the
engine oil level is indicated for
approximately 10 seconds, after the
service information. Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
control module, the
instrument panel, the
air conditioning dis
play and the multi–function display.
When the lighting reaches the mini
mum (or maximum) setting, release
it then press again to increase (or
reduce) the brightness.
As soon as the lighting is of the
brightness required, release the
button.
Trip recorder
zero reset
With the ignition on,
press the button.
INSTRUMENTS AND CONTROLS
34
18-11-2002

Monochrome screen CT
General menu
Press the "MENU" button to access
the general menu and select one of
the following applications :
• navigation guidance (see section "Satellite navigation system"),
• trip computer (see corresponding section),
• directory (see "RT3 audio/tele phone" section),
• telematics (see "RT3 audio/tele phone" section),
• configuration (see corresponding section).
MULTI–FUNCTION
SCREENS
Presentation
Monochrome screen B
This enables the following informa
tion to be displayed:
– the time,
– the date,
– the outside temperature (the °C
symbol flashes when there is a risk
of ice),
– the radio displays,
– the status of the openings (doors, bonnet...),
– the warning (e.g. "Battery charge fault") or information (e.g. "Passen
ger air bag disarmed") messages
displayed temporarily can be
cleared by pressing button 1or 2,
– the trip computer (see correspond ing section).
YOUR 807 IN DETAIL 35
Monochrome screen CT
and colour screen DT
These two systems are controlled by
the
RT3 audio/telephone keypad
and/or by a remote control keypad.
They enable the following informa
tion to be displayed:
– the time,
– the date,
– the outside temperature (a mes sage warns you when there is a
risk of ice),
– the audio source displays (radio, CD, ...),
– the telematic system displays (telephone, services, ...),
– the status of the openings (doors, bonnet, ...),
– the warning messages (e.g. "Fuel level low") and vehicle functions
status messages (e.g. "Passenger
air bag disarmed"), displayed tem
porarily,
– the trip computer display (see cor responding section),
– the satellite navigation system dis plays (see corresponding section).
Note: to enable you to use all of your
system's functions, you have two CD
ROMs: one, "Configuration", con
tains the software and the various
display and spoken information
languages, the other, "Navigation",
contains the satellite navigation
system map data.
18-11-2002

YOUR 807 IN DETAIL
36
configuration (see corresponding
section).
map (see section "Satellite naviga tion system")
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use,
displayed in the main screen win
dow.
Contextual menu:
limited menu associated with the
main application currently in use,
displayed in the main screen win
dow.
Colour screen DT
General menu
Press the
"MENU" button to access
the general menu and select one of
the following applications:
navigation guidance (see section "Satellite navigation system"),
trip computer (see corresponding section),
directory (see "RT3 audio/tele phone" section),
telematics (see "RT3 audio/tele phone" section),Parameter configuration
Monochrome screen B
Press button 1for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
– language of the information dis played,
– unit of speed (km or miles),
– unit of temperature (degrees Cel cius or Fahrenheit),
– time format (12 or 24 hours),
– hour,
– minute,
– year,
– month,
– day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.
18-11-2002

YOUR 807 IN DETAIL
36
configuration (see corresponding
section).
map (see section "Satellite naviga tion system")
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use,
displayed in the main screen win
dow.
Contextual menu:
limited menu associated with the
main application currently in use,
displayed in the main screen win
dow.
Colour screen DT
General menu
Press the
"MENU" button to access
the general menu and select one of
the following applications:
navigation guidance (see section "Satellite navigation system"),
trip computer (see corresponding section),
directory (see "RT3 audio/tele phone" section),
telematics (see "RT3 audio/tele phone" section),Parameter configuration
Monochrome screen B
Press button 1for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
– language of the information dis played,
– unit of speed (km or miles),
– unit of temperature (degrees Cel cius or Fahrenheit),
– time format (12 or 24 hours),
– hour,
– minute,
– year,
– month,
– day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.
18-11-2002

18-11-2002
YOUR 807 IN DETAIL37
For safety reasons, con
figuration of the multi
function screens by the
driver must be carried out
when stationary.
CT monochrome screen
The
"Configuration" menu gives
access to the following parameters :
– "Adjust the brightness": video dis play brightness setting.
– "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter : insert the configuration
CD ROM); activation/deactivation
of the spoken commands,
– "International parameters": choice of the display and spoken informa
tion language (German, English,
Spanish, French, Italian, Dutch,
Portuguese : insert the configura
tion CD ROM); date and time set
ting (12 or 24 hour mode, adjust
ment of the minutes on GPS); units
setting (l/100 °C or mpg – °F).
DT colour screen
The "Configuration" menu gives
access to the following parameters:
– "Choose colours": selection from the palette of colours available for
display,
– "Adjust the brightness": video dis play brightness setting.
– "Sound": voice synthesiser set ting (for the masculine/feminine
voice parameter : insert the
configuration CD ROM); activa
tion/deactivation of the spoken
commands,
– "International parameters": choice of the display and spoken informa
tion language (German, English,
Spanish, French, Italian, Dutch,
Portuguese : insert the configura
tion CD ROM); date and time
setting (12 or 24 hour mode,
adjustment of the minutes on
GPS); units setting (l/100 °C or
mpg °F).

YOUR 807 IN DETAIL
38
The remote keypad
This permits selection and validation
of the functions, commands and
parameters, displayed on the mono
chrome screen and the DT colour
screen .
It is located next to the gear lever. The knob has two functions:
–
Rotation of the knob:
This enables you to move aroundthe screen and thus select a function.
It also permits: – with a " setting" type parameter, following selection, increasing or decreas
ing of the value,
– with a " list" type parameter, after opening the list, scrolling of the values,
– with guidance on a map, increasing or decreasing of the zoomfactor.
– Pressing the knob
This permits:– access to the list of commands (contextrelated menu) of the permanent
application displayed, if no superimposed display appears,
– validation of the selected function or of the modified value,
– selection of a "setting " or "list" type parameter in order to modify it.
"MODE" button:
– Brief press: modification of the permanent application displ ay (audio
equipment, navigation/guidance, ...)
– Pressing for more than two seconds: displaying of the general information.
"ESC" button:
– Brief press: cancellation of the operation in progress or clearing of the last
superimposed display.
– Pressing for more than two seconds: clearing of all of the sup erimposed
displays and return to the permanent application.
"MENU" button:
– Brief press: acces to the general menu.
– Pressing for more than two seconds: acces to the help menu.
"MUSIC" button
– Brief press: displaying of the contextrelated menu of the act ive audio source
(tuner, CD, ...).
"TEL" button
– Brief press: opening of the line, in the case of an incomi ng call, or displaying
of the telephone source contextrelated menu.
"NAV" button:
– Brief press: displaying of the contextrelated menu of the navigation/guidance function.
"MAIN" button:
– Brief press: displaying of the general information.
18-11-2002

45
YOUR 807 IN DETAIL
Adjusting the bass When "BASS" is displayed, press button Eor Fto vary the setting.
"BASS –9" for a minimum bass setting,
"BASS 0" for a normal setting,
"BASS +9" for a maximum bass setting.
Adjusting the treble
When "TREB" is displayed, press button Eor Fto vary the setting.
"TREB –9" for a minimum treble setting,
"TREB 0" for a normal setting,
"TREB +9" for a maximum treble setting.
Adjusting the loudness
This function automatically emphasises bass and treble tones.
Press button Eor Fto switch the function on or off.
Adjusting the front/rear sound distribution (Fader)
When "FAD" is displayed, press button Eor F.
Button Eincreases the volume in the front.
Button Fincreases the volume in the rear.
Adjusting the right/left sound distribution (Balance)
When "BAL" is displayed, press button Eor F.
Button Eincreases the volume on the righthand side.
Button Fincreases the volume on the lefthand side.
Automatic volume correction "CAV"
This function enables the volume to be automatically adjuste d depending on the level of noise produced by the speed of the
vehicle.
Press buttons Eor F to switch the function on or off.
18-11-2002