2001 YAMAHA YZ250LC oil capacity

1-12
FUEL AND ENGINE MIXING OIL
GEN
INFO
EC160050
FUEL AND ENGINE MIXING OIL
Mix oil with the gas at the ratio specified below.
Always use fresh, name-brand gasoline, and mix
the oil and gas the day of the race. Do not use
premix that is more than a few hours old.
NOTE:
Except for AUS:
1. If knocking or pinging occurs, use a different
brand of gasoline or higher octane grade.
2. If unleaded gasoline is not available, then
leaded gasoline can be used.
cC
Never mix two types of oil in the same
batch; clotting of the oil could result. If you
wish to change oil types, be sure to drain
the fuel tank and the carburetor float bowl
of old premix prior to filling with the new
type.
Fuel tank capacity:
8.0 L (1.76 Imp gal, 2.11 US gal)
Mixing oil
Recommended oil:
Yamalube “2-R”
(Yamalube racing 2-cycle oil)
Mixing ratio: 30 : 1
If unavailable, use an equivalent
type of oil.
Recommended fuel:
Except for AUS:
Premium unleaded fuel with
a research octane number of
95 or higher.
For AUS:
Unleaded fuel only
5MW-9-30-1 7/3/00 1:48 PM Page 28

2-1
GENERAL SPECIFICATIONSSPEC
Model name: YZ250LC (EUROPE)
YZ250N1 (USA)
YZ250(N) (CDN, AUS, NZ, ZA)
Model code number: 5MW1 (USA, CDN, ZA)
5MW2 (EUROPE)
5MW4 (AUS, NZ)
Dimensions: USA, CDN, ZA EUROPE AUS, NZ
Overall length 2,179 mm 2,178 mm 2,179 mm
(85.8 in) (85.7 in) (85.8 in)
Overall width 827 mm¬¬
(32.6 in)
Overall height 1,307 mm 1,302 mm 1,303 mm
(51.5 in) (51.3 in) (51.3 in)
Seat height 989 mm¬¬
(38.9 in)
Wheelbase 1,482 mm¬¬
(58.3 in)
Minimum ground clearance 392 mm 391 mm 392 mm
(15.4 in) (15.4 in) (15.4 in)
Basic weight:
With oil and full fuel tank 104.5 kg (230 lb)
Engine:
Engine type Liquid cooled 2-stroke, gasoline
Cylinder arrangement Single cylinder, forward inclined
Displacement 249 cm
3(8.76 lmp oz, 8.42 US oz)
Bore ´Stroke 66.4 ´72 mm (2.614 ´2.835 in)
Compression ratio 9.1~10.6 : 1
Starting system Kick starter
Lubrication system: Premix (30 : 1)(Yamalube 2-R)
Oil type or grade (2-Cycle):
Transmission oil Yamalube 4 (10W-30) or SAE 10W-30 type SE
motor oil
Periodic oil change 0.75 L (0.66 Imp qt, 0.79 US qt)
Total amount 0.80 L (0.70 Imp qt, 0.85 US qt)
Coolant capacity (including all routes): 1.20 L (1.06 Imp qt, 1.27 US qt)
Air filter: Wet type element
Fuel:
Type Except for AUS: Premium unleaded fuel
with a research octane
number of 95 or higher
For AUS: Unleaded fuel only
Tank capacity 8.0 L (1.76 Imp gal, 2.11 US gal)
EC200000
SPECIFICATIONSEC211000
GENERAL SPECIFICATIONS
2
5MW-9-30-2 7/3/00 2:19 PM Page 2

2-4
MAINTENANCE SPECIFICATIONSSPEC
Item Standard Limit
Transmission:
Main axle deflection limit…
0.01 mm (0.0004 in)
Drive axle deflection limit…
0.01 mm (0.0004 in)
Shifter:
Shifting type Cam drum and guide bar…
Guide bar bending limit…
0.05 mm (0.0020 in)
Kick starter type: Kick and ratchet type…
Air filter oil grade (oiled filter):Foam-air-filter oil or engine mixing oil…
Carburetor:USA, CDN, ZA,
EUROPE
AUS, NZ
Type/Manufacturer
PWK38S/KEIHIN¬…
I.D. mark 5MW00 5MW10…
Main jet (M.J.) #178 #180…
Main air jet (M.A.J) #200¬…
Jet needle-clip position (J.N.) N3EJ-2 N3CW-3…
Main nozzle (N.J.) ø2.9¬…
Cutaway (C.A.) #7¬…
Pilot jet (P.J.) #50 #55…
Pilot air screw (P.A.S.) 1 1-3/4…
(for reference only)
Valve seat size (V.S.)
ø3,8 mm (0,15 in)¬…
Starter jet (G.S.) #85¬…
Power jet (P.W.J.) #50 #55 …
Float arm height (F.H.) 5.5~7.5 mm¬…
(0.22~030 in)
Reed valve:
Thickness* 0.42 mm (0.017 in)…
Valve stopper height 10.3~10.7 mm (0.406~0.421 in)…
Valve bending limit…
0.2 mm (0.008 in)
Cooling:
Radiator core size:
Width 110 mm (4.33 in)…
Height 240 mm (9.45 in)…
Thickness 32 mm (1.26 in)…
Radiator cap opening pressure 95~125 kPa…
(0.95~1.25 kg/cm
2, 13.5~17.8 psi)
Radiator capacity (total) 0.64 L (0.56 Imp qt, 0.68 US qt)…
Water pump:
Type Single-suction centrifugal pump…
5MW-9-30-2 7/3/00 2:20 PM Page 5

2-7
MAINTENANCE SPECIFICATIONSSPEC
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing…
Front suspension: USA, CDN, ZA,
EUROPE
AUS, NZ
Front fork travel
300 mm (11.8 in)¬…
Fork spring free length
460 mm (18.1 in)¬455 mm (17.9 in)
Spring rate, STD K=4.30 N/mm
K=Approx. 4.30 N/mm…
(0.430 kg/mm, (0.430 kg/mm)
24.1 lb/in) 24.1 lb/in
Optional spring/Spacer Yes¬…
Oil capacity 573 cm
3¬…
(20.2 Imp oz,
19.4 US oz)
Oil level
135 mm (5.31 in)¬…
80~150 mm ¬…
(From top of outer tube with inner tube(3.15~5.91 in)
and damper rod fully compressed
without spring.)
Oil grade Suspension oil ¬…
“01”
Inner tube outer diameter
46 mm (1.81 in)¬…
Front fork top endZero mm (Zero in)¬…
Rear suspension: USA, CDN, ZA,
EUROPE
AUS,NZ
Shock absorber travel
132 mm (5.20 in)¬…
Spring free length
260 mm (10.24 in) 275 mm (10.83 in)…
Fitting length
244 mm (9.61 in)267 mm (10.51 in)…

242~260 mm 257~275 mm…
(9.53~10.24 in) (10.12~10.83 in)
Spring rate, STD K=48 N/mm K=Approx. 50 N/mm…
(4.8 kg/mm, (5.0 kg/mm,
269 lb/in) 280 lb/in)
Optional spring Yes¬…
Enclosed gas pressure
1,000 kPa¬…
(10 kg/cm2, 142 psi)
Swingarm:
Swingarm free play limit
End…
1.0 mm (0.04 in)
Side clearance…
0.2~0.9 mm
(0.008~0.035 in)
5MW-9-30-2 7/3/00 2:20 PM Page 8

INSP
ADJ
3-14
PILOT AIR SCREW ADJUSTMENT
4. Remove:
9Oil drain bolt 1
9Oil filler cap 2
Drain the transmission oil.
5. Install:
9Aluminum washer
9Oil drain bolt 1
6. Fill:
9Transmission oil
Recommended oil:
Yamalube 4 (10W-30) or SAE
10W-30 type SE motor oil
Oil capacity
(periodic oil change):
0.75 L (0.66 Imp qt, 0.79 US qt)
20 Nm (2.0 m•kg, 14 ft•lb)
7. Check:
9Oil leakage
8. Check:
9Transmission oil level
9. Install:
9Oil filler cap 2
EC35L021
PILOT AIR SCREW ADJUSTMENT
1. Adjust:
9Pilot air screw 1
Adjusting steps:
9Turn in the pilot air screw until it is lightly
seated.
9Turn out the pilot air screw by the factory-set
number of turns.
NOTE:
To optimize the fuel flow at a smaller throttle
opening, each machine’s pilot air screw has
been individually set at the factory. Before
adjusting the pilot air screw, turn it in fully and
count the number of turns. Record this num-
ber as the factory-set number of turns out.
Pilot air screw:
1 turn out
*1-3/4 turns out
(for reference only)
*For EUROPE
5MW-9-30-3A 7/3/00 2:52 PM Page 36