2001 YAMAHA YZ250F brake light

GEN
INFO

1 - 1
DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1
Clutch lever
2
Decompression lever
3
Front brake lever
4
Throttle grip
5
Radiator cap
6
Fuel tank cap
7
Oil tank cap
8
Engine stop switch
9
Kickstarter crank
0
Fuel tank
A
Radiator
B
Coolant drain bolt
C
Rear brake pedal
D
Valve joint
E
Fuel cock
F
Cold starter knob
G
Hot starter knob (red)
H
Drive chain
I
Air filter
J
Shift pedal
K
Front fork
NOTE:

l
The machine you have purchased may differ
slightly from those shown in the following.
l
Designs and specifications are subject to
change without notice.
1

2 - 21
SPEC

CABLE ROUTING DIAGRAM
1Brake hose
2Brake hose holder
3Brake master cylinderInstall the brake hose to the brake caliper with the
paint on the pipe facing the brake caliper and with
the pipe contacting the brake caliper projection.
õPass the brake hose into the brake hose holders.
‚If the brake hose contacts the spring (rear shock
absorber), correct its twist.
ëInstall the brake hose so that its pipe portion
directs as shown and lightly touches the projection
on the brake master cylinder.
A
A 2
3
1
12
3 ë
‚
õ

3 - 45
INSP
ADJ
LUBRICATION
LUBRICATION
To ensure smooth operation of all compo-
nents, lubricate your machine during setup,
after break-in, and after every race.
1All control cable
2Clutch lever pivot
3Shift pedal pivot
4Footrest pivot
5Throttle-to-handlebar contact
6Drive chain
7Tube guide cable winding portion
8Throttle cable end
9Clutch cable end
0Decompression cable endUse Yamaha cable lube or equivalent on these
areas.
õUse SAE 10W-30 motor oil or suitable chain
lubricants.
‚Lubricate the following areas with high quality,
lightweight lithium-soap base grease.
CAUTION:
Wipe off any excess grease, and avoid get-
ting grease on the brake discs.
AAA
AAB
CC

5 - 18
CHASFRONT BRAKE AND REAR BRAKE
2. Install:
lCopper washer 1
lUnion bolt 2
WARNING
Always use new copper washers.
ACHTUNG:CAUTION:
Install the brake hose so that its pipe por-
tion a directs as show and lightly touches
the projection b on the brake caliper.
T R..30 Nm (3.0 m · kg, 22 ft · lb)
3. Install:
lBrake hose holder 1
lBrake caliper 2
lBolt (brake caliper) 3
NOTE:
Fit the brake hose holder cut a over the pro-
jection b on the front fork and clamp the brake
hose.
4. Tighten:
lPad pin 4
5. Install:
lPad pin plug 5
Rear brake caliper
1. Install:
lPad support 1
lBrake pad 2
lPad pin 3
NOTE:
lInstall the brake pads with their projections
a into the brake caliper recesses b.
lTemporarily tighten the pad pin at this point.
T R..23 Nm (2.3 m · kg, 17 ft · lb)
T R..18 Nm (1.8 m · kg, 13 ft · lb)
T R..3 Nm (0.3 m · kg, 2.2 ft · lb)

5 - 24
CHASFRONT BRAKE AND REAR BRAKE
4. Install:
lCopper washer 1
lBrake hose 2
lUnion bolt 3
WARNING
Always use new copper washers.
ACHTUNG:CAUTION:
Install the brake hose so that its pipe por-
tion a directs as show and lightly touches
the projection b on the brake master cylin-
der.
T R..30 Nm (3.0 m · kg, 22 ft · lb)
Rear brake hose
1. Install:
lCopper washer 1
lBrake hose 2
lCopper washer 3
lUnion bolt 4
WARNING
Always use new copper washers.
ACHTUNG:CAUTION:
When installing the brake hose, first align
the tooth a on the copper washer 1 with
the projection b on the brake master cylin-
der. Then, align the pipe portion c on the
end of the brake hose with the tooth d on
the copper washer 1 and tighten the union
bolt.
T R..30 Nm (3.0 m · kg, 22 ft · lb)