2001 YAMAHA YZ125LC light

5-24
CHASFRONT BRAKE AND REAR BRAKE
EC5A5500
Rear brake hose
1. Install:
9Copper washer 1
9Brake hose 2
9Union bolt 3
w
Always use new copper washers.
cC
Install the brake hose so that its pipe por-
tion
a adirects as show and lightly touches
the projection
b bon the master cylinder.
30 Nm (3.0 m•kg, 22 ft•lb)
4. Install:
9Copper washer 1
9Brake hose 2
9Union bolt 3
w
Always use new copper washers.
cC
Install the brake hose so that its pipe por-
tion a a
directs as show and lightly touches
the projection b b
on the master cylinder.
30 Nm (3.0 m•kg, 22 ft•lb)
5MV-9-30-5A 6/19/00 1:36 PM Page 48

7-10
TUNSETTING
EC71C020
Road condition and examples of carburetor setting
EC71D040
Examples of carburetor setting depending on symptom
Symptom Setting Checking
At full throttle Increase main jet calibration No. Discoloration of spark plug
Õ
Stall at high speeds (Gradually) If tan color, it is in good condition.
* Hard breathing If can not be normalized:
Shearing noise Clogged float valve seat
Whitish spark plug Clogged fuel hose
Clogged fuel cock
Lean mixture
At full-throttle Decrease main jet calibration No. Discoloration of spark plug Õ
Stop of speed pick-up (Gradually) If tan color, it is in good condition.
Slow speed pick-up *In case of racing slight enrichment If not effect:
of mixture reduces engine trouble. Clogged air cleaner
Slow response Fuel overflow from carburetor
Sooty spark plug Clogged main air passage or clogged
filter
Rich mixture
Lean mixture Lower jet needle clip position.
(1 groove down)
Rich mixture Raise jet needle clip position.
(1 groove up)
1/4~3/4 throttle Lower jet needle clip position.
* Hard breathing (1 groove down)
Lack of speed
1/4~1/2 throttle Raise jet needle clip position.
Slow speed pick-up (1 groove up)
White smoke
Poor acceleration
Conditions General condition Sandy condition
Under 10°C 15~25°C Over 30°C Under 10°C 15~25°C Over 30°C
(50°F) (59~77°F) (86°F) (50°F) (59~77°F) (86°F)
Parts (Winter)(Spring, Autumn)(Summer) (Winter)(Spring, Autumn)(Summer)
Main jet#470 #460 #450 #490 #480 #470
*#460 *#450 *#440 *#470 *#460 *#450
Jet needle6BGK10-75-3 6BGK9-75-3 6BGK9-75-3 6BGK9-75-4 6BGK10-75-3 6BGK10-75-3
*6BHY25-75-3 *6BHY1-75-3 *6BHY1-75-3 *6BHY1-75-4 *6BHY25-75-3 *6BHY25-75-3
Pilot jet#25 #25 #25 #25 #25 #25
*#30 *#30 *#30 *#30 *#30 *#30
Pilot air screw1 1-1/4 1-1/2 1 1-1/4 1-1/2
*1-1/4 *1-1/2 *1-3/4 *1-1/4 *1-1/2 *1-3/4
Leaner
(Standard)
Richer
Õ
Õ
Clip position indicates the position of jet
needle groove, to which the clip is fitted.
The position is numbered from the top.
If a change in the clip position (1
groove) is effective, try another jet nee-
dle that provides a difference of 0.5 in
the clip position.
*For EUROPE
5MV-9-30-7A 6/19/00 1:24 PM Page 24

7-12
TUNSETTING
EC71M001
Change of the heat range of spark plugs
Judging from the discoloration of spark plugs, if
they are found improper, it can be corrected by
the following two methods; changing carburetor
settings and changing the heat range of spark
plug.
9In principle, it is advisable to first use spark
plugs of standard heat range, and judging from
the discoloration of spark plugs, adjust carbure-
tor settings.
9If the calibration No. of the main jet must be
changed by ±30, it is advisable to change the
heat range of spark plugs and newly select the
proper main jet.
NOTE:
9When checking the discoloration of spark
plugs, be sure to stop the engine immediately
after a run and check.
9Avoid racing.
9When changing the heat range of spark plugs,
never attempt to change it more than ±1 rank.
9When using spark plugs other than standard,
make sure of the difference in heat range and
find the equivalent to the standard.
9Note that even if the discoloration seems prop-
er, it may slightly vary with the spark plug
maker and oil in use.
Standard spark plug BR9EG/NGK
5MV-9-30-7A 6/19/00 1:24 PM Page 32