OPERATION AND IMPORTANT RIDING POINTS
5-4
5
EAU00424
Tips for reducing fuel
consumptionFuel consumption depends largely on
your riding style. Consider the following
tips to reduce fuel consumption:l
Thoroughly warm up the engine.
l
Turn the starter (choke) off as
soon as possible.
l
Shift up swiftly, and avoid high en-
gine speeds during acceleration.
l
Do not rev the engine while shift-
ing down, and avoid high engine
speeds with no load on the engine.
l
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at traf-
fic lights or at railroad crossings).
EAU00436
Engine break-in There is never a more important period
in the life of your engine than the period
between 0 and 1,000 km. For this rea-
son, you should read the following ma-
terial carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1,000 km. The various parts in the en-
gine wear and polish themselves to the
correct operating clearances. During
this period, prolonged full-throttle oper-
ation or any condition that might result
in engine overheating must be avoided.
EAU00444*
0–150 kml
Avoid prolonged operation above
1/3 throttle.
l
After every hour of operation, stop
the engine, and then let it cool for
five to ten minutes.
l
Vary the engine speed from time
to time. Do not operate the engine
at one set throttle position.
150–500 km
l
Avoid prolonged operation above
1/2 throttle.
l
Rev the engine freely through the
gears, but do not use full throttle at
any time.
500–1,000 km
Avoid prolonged operation above
3/4 throttle.
EC000056*
CAUTION:@ After 1,000 km of operation, the en-
gine oil and final gear oil must be
changed, and the oil filter element
replaced. @
E_3bt.book Page 4 Thursday, September 7, 2000 10:01 AM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-2
6
EAU03685
Periodic maintenance and lubrication chart
NOTE:_ l
The annual checks must be performed every year, except if a kilometer-based maintenance is performed instead.
l
From 50,000 km, repeat the maintenance intervals starting from 10,000 km.
l
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and techni-
cal skills.
_CP-03ENO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (´1,000 km)
ANNUAL
CHECK
1 10203040
1
*Fuel line• Check fuel hoses and vacuum hose for cracks or damage.ÖÖÖÖ Ö
2*Fuel filter• Check condition.ÖÖ
3 Spark plugs• Check condition.
• Clean and regap.ÖÖ
• Replace.ÖÖ
4*Valves• Check valve clearance.
•Adjust.ÖÖÖÖ
5 Air filter element•Clean.ÖÖ
• Replace.ÖÖ
6*Battery• Check electrolyte level and specific gravity.
• Make sure that the breather hose is properly routed.ÖÖÖÖ Ö
7Clutch• Check operation.
•Adjust.ÖÖÖÖÖ
8*Front brake• Check operation, fluid level and vehicle for fluid leakage.
(See NOTE on page 6-4.)ÖÖÖÖÖ Ö
• Replace brake pads. Whenever worn to the limit
9*Rear brake• Check operation and adjust brake pedal freeplay.ÖÖÖÖÖ Ö
• Replace brake shoes. Whenever worn to the limit
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6
EAU03715
Cleaning the air filter element The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas.
1. Remove the seats. (See page 3-7
for seat removal and installation
procedures.)
2. Remove the fuel tank bolts.3. Lift the front of the fuel tank to po-
sition it away from the air filter
case. (Do not remove the fuel
tank!)
EW000071
WARNING
_ l
Make sure that the fuel tank is
well supported.
l
Do not tilt or pull the fuel tank
too much, otherwise the fuel
hoses may come loose, which
could cause fuel leakage.
_4. Remove the air filter case cover
screw.5. Slide the air filter case cover so as
to unhook the tab on the rear of
the cover from the holder on the
frame, and then lift the air filter
case cover without removing it.
1. Fuel tank
2. Bolt (´ 3)
1. Screw
1. Air filter case cover
2. Tab
3. Holder
4. Air filter element
E_3bt.book Page 11 Thursday, September 7, 2000 10:01 AM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
6 6. Pull the air filter element out.
7. Lightly tap the air filter element to
remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.
8. Insert the air filter element into the
air filter case.
EC000082
CAUTION:_ l
Make sure that the air filter ele-
ment is properly seated in the
air filter case.
l
The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
_9. Place the air filter case cover in the
original position, and then install
the screw.
10. Install the fuel tank by installing the
bolts.
EW000131
WARNING
_ Make sure that the fuel hoses and
vacuum hose are properly connect-
ed and routed, and not pinched. Re-
place any damaged hoses. _
EC000086
CAUTION:_ When installing the fuel tank bolts,
make sure that the washers, rubber
dampers and spacers are posi-
tioned properly. _11. Install the seats.
1. Air filter element
1. Washer
2. Rubber damper
3. Spacer
E_3bt.book Page 12 Thursday, September 7, 2000 10:01 AM
8-1
8
EAU01038
8-SPECIFICATIONSSpecificationsCS-01E
Model XV535
Dimensions
Overall length 2,225 mm (except for N, S, SF)
2,250 mm (for N, S, SF)
Overall width 780 mm
Overall height 1,120 mm
Seat hight 720 mm
Wheelbase 1,520 mm
Ground clearance 160 mm
Minimum turning radius 2,900 mm
Basic weight (with oil and full
fuel tank)
195 kg (except for A)
197 kg (for A)
Engine
Engine type Air-cooled 4-stroke, SOHC
Cylinder arrangement V-type, 2-cylinder
Displacement 535 cm
3
Bore ´ Stroke 76.0 ´ 59.0 mm
Compression ratio 9:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG type or
higher
Quantity
Without oil filter element
replacement 2.6 L
With oil filter element
replacement 2.8 L
Total amount (dry engine) 3.2 L
-20 -10 0
10 20 30
40
50 °C
SAE 10W–30
SAE 15W–40SAE 20W–40SAE 20W–50
SAE 10W–40
CAUTION:Be sure to use motor oils that do not contain anti-friction
modifiers. Passenger car motor oils (often labeled
“ENERGY CONSERVING II”) contain anti-friction additives
which will cause clutch and/or starter clutch slippage, result-
ing in reduced component life and poor engine performance.
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM
SPECIFICATIONS
8-2
8
Final gear oil
Type Hypoid gear oil SAE 80
(API GL4) or multigrade hypoid
gear oil SAE 80W-90
Quantity 0.19 L
Air filterDry type element
Fuel
Ty p e
Regular unleaded gasoline
Fuel tank capacity 13.5 L
Fuel reserve amount 2.5 L
Carburetor
Manufacturer MIKUNI
Model ´ quantity BDS34 ´ 2
Spark plug
Manufacturer/model NGK / BPR6ES or
DENSO / W20EPR-U
Gap 0.7–0.8 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Spur gear
Primary reduction ratio 1.944
Secondary reduction system Shaft drive
Secondary reduction ratio 3.071
Transmission type Constant mesh, 5-speed
Operation Left footGear ratio
1st 2.714
2nd 1.900
3rd 1.458
4th 1.167
5th 0.967
Chassis
Frame type Pressed backbone
Caster angle 31.5°
Trail 125 mm
Tires
Front
Type Tube tire
Size 3.00-19 49S
Manufacturer/
model Bridgestone / L303A
Dunlop / F14G
Rear
Type Tube tire
Size 140/90-15 M/C 70S
Manufacturer/
model Bridgestone / G508
Dunlop / K425
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM
10-INDEXAAir filter element, cleaning ...................... 6-11BBattery ................................................... 6-29
Brake and clutch levers, checking and
lubricating ............................................ 6-25
Brake and shift pedals, checking and
lubricating ............................................ 6-25
Brake fluid, changing ............................. 6-23
Brake fluid level, checking...................... 6-22
Brake lever...............................................3-4
Brake lever free play, adjusting .............. 6-19
Brake light switch, adjusting ................... 6-21
Brake pads and shoes, checking ........... 6-21
Brake pedal..............................................3-4
Brake pedal position and free play,
adjusting .............................................. 6-19CCables, checking and lubricating............ 6-23
Carburetors, adjusting............................ 6-13
Care.........................................................7-1
Clutch lever ..............................................3-3
Clutch lever free play, adjusting ............. 6-18
Conversion table ......................................8-5DDimmer switch .........................................3-2
EEngine break-in ....................................... 5-4
Engine oil and oil filter element ................ 6-7
Engine stop switch................................... 3-3FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-27
Fuel ......................................................... 3-5
Fuel consumption, tips for reducing ......... 5-4
Fuel reserve switch.................................. 3-3
Fuel tank cap ........................................... 3-5
Fuses, replacing .................................... 6-31HHandlebar switches ................................. 3-2
Headlight bulb, replacing ....................... 6-31
Helmet holder .......................................... 3-9
High beam indicator light ......................... 3-1
Horn switch ............................................. 3-2IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-13
Ignition circuit cut-off system.................. 3-10
Indicator lights ......................................... 3-1KKey identification number ........................ 9-1
LLight switch ..............................................3-3MMain switch ..............................................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-1PParking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-2
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .......................................................3-7
Passenger seat...................................3-7
Rider seat ...........................................3-8
Shifting .....................................................5-3
Shift pedal ................................................3-4
Shift points (for Switzerland only) .............5-3
Shock absorber assemblies, adjusting .....3-9
Sidestand ...............................................3-10
Sidestand, checking and lubricating .......6-25
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM