2001 YAMAHA XL 800 lock

1-10
E
EJU00613
Cruising limitations
●Scan constantly for people, objects, and
other watercraft. Be alert for conditions
that limit your visibility or block your vision
of others.
●Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft.
●Do not follow directly behind watercraft or
other boats.
●Do not go near others to spray or splash
them with water.
●Avoid sharp turns or other maneuvers
that make it hard for others to avoid you or
understand where you are going.
●Avoid areas with submerged objects or
shallow water.
●Ride within your limits and avoid aggres-
sive maneuvers to reduce the risk of loss
of control, ejection, and collision.
●This is a high performance boat—not a
toy. Sharp turns or jumping wakes or
waves can increase the risk of back/spinal
injury (paralysis), facial injuries, and bro-
ken legs, ankles and other bones. Do not
jump wakes or waves.
●Do not operate the watercraft in rough
water, bad weather or when visibility is
poor; this may lead to an accident caus-
ing injury or death. Be alert to the possi-
bility of adverse weather. Take note of
weather forecasts and the prevailing
weather conditions before setting out on
your watercraft.
●As with any water sport, you should not
ride your watercraft without someone else
near by. If you ride further than swimming
distance from shore, you should ride by
another boat or watercraft, but make sure
you stay a safe distance away. It’s good
common sense!
●Never operate in water that is less than
60 cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged
object, which could result in injury.
E_F0P71-1.fm Page 10 Tuesday, July 18, 2000 7:10 PM

E
2
EJU00326
FEATURES AND
FUNCTIONS
Location of main components............... 2-1
Operation of controls and other
functions.................................................... 2-5
Rear seat................................................. 2-5
Front seat ................................................ 2-6
Hood ........................................................ 2-7
Fuel tank filler cap ................................... 2-8
Oil tank filler cap...................................... 2-8
Fuel cock knob........................................ 2-9
Engine stop switch ................................ 2-10
Engine shut-off switch........................... 2-10
Choke knob ........................................... 2-10
Throttle lever ......................................... 2-11
Start switch............................................ 2-11
Cooling water pilot outlet ...................... 2-12
Steering system .................................... 2-12
Tilt lever ................................................. 2-13
Shift lever .............................................. 2-14
Quick Shift Trim System (QSTS)
selector .................................................. 2-15
Engine overheat warning system ......... 2-17
Handgrip................................................ 2-18
Multifunction meter................................ 2-19
PADLOC (Programmable digital locking
ignition) .................................................. 2-20
Tachometer ........................................... 2-22
Speedometer ........................................ 2-23
Fuel meter ............................................. 2-23
Engine oil meter .................................... 2-24
Clock ..................................................... 2-24
Hour meter ............................................ 2-25
Trip timer ............................................... 2-25
Tripmeter ............................................... 2-26
Fuel warning indicator........................... 2-26
Oil warning indicator ............................. 2-27
Engine overheat warning indicator....... 2-27
Battery warning indicator ...................... 2-28
Storage compartments ......................... 2-29
E_F0P71-2TOC.fm Page 1 Tuesday, July 18, 2000 7:12 PM

2-1
E
EJU00327
Location of main components
1Handlebars
Use to control direction.
2Fuel tank filler cap
3Rope hole
4Footwell
Use to place feet for balance.
5Footrest
Use for stopping when pulling a water-skier.
6Front seat latch
7Rear seat latch
Locking and releasing the seat rock.
8Intake grate
Prevents debris from getting into the jet pump.
9Speed sensor
E_F0P71-2.fm Page 1 Tuesday, July 18, 2000 8:20 PM

2-3
E
1Engine shut-off cord (lanyard)
Attach to wrist so that the engine stops if the
operator falls off the watercraft.
2Engine stop switch
Push to stop the engine normally.
3Clip
Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental starting of the engine or unauthorized
use of the watercraft.
4Quick Shift Trim System (QSTS) selector
Use to select the trim angle of the watercraft.
5QSTS shift lock lever
6Engine shut-off switch
Remove the clip to stop the engine and dis-
able it from starting.
7Start switch
Push to start the engine.8Adjustable rearview mirrors
9Multifunction meter
Use to check watercraft operation.
0Shift lever
Use to put the watercraft into forward or
reverse.
AThrottle lever
Use to accelerate and decelerate.
BTilt lever
Use to adjust the tilt of the handlebars.
CReverse gate
Controls direction of jet thrust when in reverse.
DStern drain plugs
Use to drain water in the bilge when the water-
craft is on dry land.
EJet thrust nozzle
Changes the direction of jet thrust according
to handlebar position.
FRide plate
E_F0P71-2.fm Page 3 Tuesday, July 18, 2000 8:20 PM

2-5
E
EJU00328
Operation of controls and
other functions
EJU00335a
Rear seat
To remove the rear seat:
Pull the rear seat latch 1 up, and then
pull the seat off.
To install the rear seat:
Insert the projections on the front of the
seat into the stays on the deck, and then
push the rear of the seat down to lock it in
place securely.
E_F0P71-2.fm Page 5 Tuesday, July 18, 2000 8:20 PM

2-6
E
EJU00714
Front seat
To remove the front seat:
1. Remove the rear seat.
2. Pull the front seat latch 2 up, and then
pull the seat off.
To install the front seat:
1. Insert the projections on the front of the
seat into the stays on the deck, and then
push the rear of the seat down to lock it
in place.
2. Install the rear seat.
NOTE:
Make sure that the seats are properly
secured before operating the watercraft.
E_F0P71-2.fm Page 6 Tuesday, July 18, 2000 8:20 PM

2-7
E
EJU00703
Hood
To open the hood, pull the latch 1 up,
and then lift the hood up.
To close the hood, push the hood down to
lock it in place.
NOTE:
Make sure that the hood is properly secured
before operating the watercraft.
E_F0P71-2.fm Page 7 Tuesday, July 18, 2000 8:20 PM

2-8
E
EJU00347
Fuel tank filler cap
To remove the fuel tank filler cap 1, turn it
counterclockwise.
NOTE:
Make sure that the fuel tank filler cap is
properly secured before operating the water-
craft.
EJU00001N
Oil tank filler cap
To remove the oil tank filler cap:
1. Open the hood. (See page 2-7 for hood.)
2. Turn the filler cap 2 counterclockwise.
To install the oil tank filler cap:
Install the filler cap, and then close the
hood.
NOTE:
Make sure that the oil tank filler cap and
hood are properly secured before operating
the watercraft.
E_F0P71-2.fm Page 8 Tuesday, July 18, 2000 8:20 PM