2001 YAMAHA WR 250F torque

SPEC
2 - 17
MAINTENANCE SPECIFICATIONS
EC212300
ELECTRICAL
Item Standard Limit
Ignition system:
Advancer type Electrical ----
CDI:
Magneto-model/manufacturer F5NG 00/YAMAHA----
Charging coil 1 resistance (color) 640 ~ 960 W at 20 ˚C (68 ˚F)
(Green – Brown)----
Charging coil 2 resistance (color) 464 ~ 696 W at 20 ˚C (68 ˚F)
(Green – Pink)----
Lighting coil resistance (color) 0.16 ~ 0.24 W at 20 ˚C (68 ˚F)
(Black – Yellow)----
Pickup coil resistance (color) 248 ~ 372 W at 20 ˚C (68 ˚F)
(White – Red)----
CDI unit-model/manufacturer 5PH-00/YAMAHA ----
Ignition coil:
Model/manufacturer 4SR-00/YAMAHA ----
Minimum spark gap 6 mm (0.24 in) ----
Primary coil resistance 0.20 ~ 0.30 W at 20 ˚C (68 ˚F) ----
Secondary coil resistance 9.5 ~ 14.3 kW at 20 ˚C (68 ˚F) ----
Part to be tightened Thread size Q’tyTightening torque
Nm m·kg ft·lb
Stator M6 ´ 1.0 3 10 1.0 7.2
Rotor M10 ´ 1.25 1 48 4.8 35
Neutral switch M5 ´ 0.8 2 4 0.4 2.9
Ignition coil M6 ´ 1.0 2 7 0.7 5.1

SPEC
2 - 18
EC220001
GENERAL TORQUE SPECIFICATIONS
This chart specifies torque for standard fasten-
ers with standard I.S.O. pitch threads. Torque
specifications for special components or
assemblies are included in the applicable sec-
tions of this book. To avoid warpage, tighten
multi-fastener assemblies in a crisscross fash-
ion, in progressive stages, until full torque is
reached. Unless otherwise specified, torque
specifications call for clean, dry threads. Com-
ponents should be at room temperature.
A: Distance between flats
B: Outside thread diameter
EC230000
DEFINITION OF UNITS
A
(Nut)B
(Bolt)TORQUE
SPECIFICATION
Nm m•kg ft•lb
10 mm
12 mm
14 mm
17 mm
19 mm
22 mm6 mm
8 mm
10 mm
12 mm
14 mm
16 mm6
15
30
55
85
1300.6
1.5
3.0
5.5
8.5
134.3
11
22
40
61
94
Unit Read Definition Measure
mm
cmmillimeter
centimeter10
-3 meter
10-2 meterLength
Length
kg kilogram 10
3 gram Weight
N Newton 1 kg ´ m/sec
2 Force
Nm
m • kgNewton meter
Meter kilogramN ´ m
m ´ kgTorque
Torque
Pa Pascal N/m
2Pressure
N/mm Newton per millimeter N/mm Spring rate
L
cm
3 Liter
Cubic centimeter—
—Volume or capacity
Volume or capacity
r/min Revolution per minute — Engine speed
GENERAL TORQUE SPECIFICATIONS/
DEFINITION OF UNITS

3 - 45
INSP
ADJ
STEERING HEAD INSPECTION AND ADJUSTMENT
lTighten the steering ring nut 3 using
steering nut wrench 4.
NOTE:
Set the torque wrench to the steering nut
wrench so that they form a right angle.
Steering nut wrench:
YU-33975/90890-01403
T R..
Steering ring nut (initial tighten-
ing):
38 Nm (3.8 m • kg, 27 ft • lb)
lLoosen the steering ring nut one turn.
lRetighten the steering ring nut using the
steering nut wrench.
WARNING
Avoid over-tightening.
T R..
Steering ring nut (final tighten-
ing):
7 Nm (0.7 m • kg, 5.1 ft • lb)
lCheck the steering stem by turning it lock
to lock. If there is any binding, remove the
steering stem assembly and inspect the
steering bearings.
lInstall the upper bracket 5, steering stem
nut 6, handlebar 7, handlebar holder 8
and headlight 9.
NOTE:
lThe upper handlebar holder should be
installed with the punched mark a for-
ward.
lInsert the end of fuel breather hose 0 into
the hole of the steering stem.
CAUTION:
First tighten the bolts on the front side of
the handlebar holder, and then tighten
the bolts on the rear side.
T R..
Steering stem nut:
145 Nm (14.5 m • kg, 105 ft • lb)
Handlebar upper holder:
28 Nm (2.8 m • kg, 20 ft • lb)
Pinch bolt (handle crown):
23 Nm (2.3 m • kg, 17 ft • lb)
Headlight:
7 Nm (0.7 m • kg, 5.1 ft • lb)

4 - 26
ENGCAMSHAFTS
CAUTION:
Do not turn the crankshaft during the
camshaft installation. Damage or
improper valve timing will result.
lInstall the clips, camshaft caps 4 and
bolts (camshaft cap) 5.
T R..
Bolt (camshaft cap):
10 Nm (1.0 m • kg, 7.2 ft • lb)
NOTE:
lBefore removing the clips, cover the cylin-
der head with a clean rag to prevent the
clips from into the cylinder head cavity.
lApply the engine oil on the thread and con-
tact surface of the bolts (camshaft cap).
lTighten the bolts (camshaft cap) 5 in a
crisscross pattern.
CAUTION:
The bolts (camshaft cap) must be tight-
ened evenly or damage to the cylinder
head, camshaft caps and camshaft will
result.
2. Install:
lTiming chain tensioner
Installation steps:
lWhile pressing the tensioner rod lightly
with fingers, use a thin screwdriver and
wind the tensioner rod up fully clockwise.
lWith the rod fully wound and the chain
tensioner UP mark a facing upward,
install the gasket 1 and the timing chain
tensioner 2, and tighten the bolt 3 to the
specified torque.
T R..
Bolt (timing chain tensioner):
10 Nm (1.0 m • kg, 7.2 ft • lb)

4 - 27
ENG
lRelease the screwdriver, check the ten-
sioner rod to come out and tighten the
gasket 4 and the cap bolt 5 to the speci-
fied torque.
T R..
Tensioner cap bolt:
7 Nm (0.7 m • kg, 5.1 ft • lb)
3. Turn:
lCrankshaft
Counterclockwise several turns
4. Check:
lRotor T.D.C. mark
Align with the crankcase align mark.
lCamshaft match marks
Align with the cylinder head surface.
Out of alignment ® Adjust.
5. Install:
lTiming mark accessing screw 1
lCrankshaft end accessing screw 2
6. Install:
lTiming chain guide (top side) 1
lCylinder head cover gasket 2
lCylinder head cover 3
lBolt (cylinder head cover) 4
NOTE:
Apply the sealant on the cylinder head cover
gasket.
Quick gasket®:
ACC-QUICK-GS-KT
YAMAHA Bond No. 1215:
90890-85505
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)
CAMSHAFTS

ENG
4 - 86
DEPOSE DU MOTEUR
MOTOR DEMONTIEREN
RIMOZIONE DEL MOTORE
2. Montieren:
lSicherungsscheibe 1
lMutter (Antriebsritzel) 2
HINWEIS:
Beim Festziehen der Mutter die Hin-
terradbremse betätigen.
T R..75 Nm (7,5 m · kg)
3. Die Lasche der Sicherungs-
scheibe umbiegen, um die
Mutter zu sichern.
4. Montieren:
lAntriebskettenritzel 1
lKettenschutz 2
lSchraube (Kettenschutz) 3
T R..8 Nm (0,8 m · kg)
Ölschlauch und Leerlaufschalter
1. Montieren:
lO-Ring 1
lPaßstift 2
lÖlschlauch 3
lSchraube (Ölschlauch) 4
HINWEIS:
Lithiumfett auf den O-Ring auftragen.
2. Montieren:
lFeder 1
lStift 2
lO-Ring 3
lLeerlaufschalter 4
lSchraube (Leerlaufschalter)
5
HINWEIS:
Lithiumfett auf den O-Ring auftragen.
T R..10 Nm (1,0 m · kg)
T R..4 Nm (0,4 m · kg)
2. Monter:
lRondelle-frein 1
lEcrou (pignon d’entraînement)
2
N.B.:
Serrer l’écrou en actionnant le frein
arrière.
T R..75 Nm (7,5 m · kg, 54 ft · lb)
3. Courber la languette de la ron-
delle-frein pour verrouiller
l’écrou.
4. Monter:
lGuide de pignon de chaîne de
transmission 1
lCouvercle de chaîne 2
lVis (couvercle de chaîne) 3
T R..8 Nm (0,8 m · kg, 5,8 ft · lb)
Durit d’huile et contacteur de point
mort
1. Monter:
lJoint torique 1
lGoujon 2
lDurit d’huile 3
lBoulon (durit d’huile) 4
N.B.:
Enduire le joint torique de graisse à base
de savon au lithium.
2. Monter:
lRessort 1
lGoupille 2
lJoint torque 3
lContacteur de point mort 4
lBoulon (contacteur de point
mort) 5
N.B.:
Enduire le joint torique de graisse à base
de savon au lithium.
T R..10 Nm (1,0 m · kg, 7,2 ft · lb)
T R..4 Nm (0,4 m · kg, 2,9 ft · lb)
2. Installare:
lRondella di bloccaggio 1
lDado (corona dentata trasmis-
sione) 2
NOTA:
Avvitare il dado agendo sul freno poste-
riore.
T R..75 Nm (7,5 m · kg, 54 ft · lb)
3. Piegare la linguetta della ron-
della di bloccaggio.
4. Installare:
lGuida corona catena di tra-
smissione 1
lCarterino corona catena di tra-
smissione 2
lVite (carterino corona catena di
trasmissione) 3
T R..8 Nm (0,8 m · kg, 5,8 ft · lb)
Flessibile dell’olio e interruttore di
folle
1. Installare:
lO-ring 1
lGrano di centraggio 2
lFlessibile dell’olio 3
lBullone (tubo flessibile
dell’olio) 4
NOTA:
Applicare grasso a base di sapone di litio
sull’O-ring.
2. Installare:
lMolla 1
lPerno 2
lO-ring 3
lInterruttore folle 4
lBullone (interruttore folle) 5
NOTA:
Applicare grasso a base di sapone di litio
sull’O-ring.
T R..10 Nm (1,0 m · kg, 7,2 ft · lb)
T R..4 Nm (0,4 m · kg, 2,9 ft · lb)

5 - 39
CHASFRONT FORK
26. Tighten:
lFront fork cap bolt (locknut) 1
NOTE:
lWhile compressing the fork spring, set the
thin type spanners 2 between the spacer 3
and spring guide 4.
lHold the locknut 5 and tighten the front fork
cap bolt with specified torque.
T R..29 Nm (2.9 m · kg, 21 ft · lb)
27. Install:
lFront fork cap bolt 1
To outer tube.
NOTE:
Temporarily tighten the cap bolt.
28. Install:
lProtector guide 1
Installation
1. Install:
lFront fork 1
NOTE:
lTemporarily tighten the pinch bolts (lower
bracket).
lDo not tighten the pinch bolts (upper bracket) yet.
2. Tighten:
lFront fork cap bolt 1
3. Adjust:
lFront fork top end a
* For EUROPE
** For AUS, NZ and ZA
Front fork top end (standard) a:
7 mm (0.28 in)
* 8 mm (0.31 in)
** 10.5 mm (0.41 in)
T R..30 Nm (3.0 m · kg, 22 ft · lb)

5 - 40
CHASFRONT FORK
4. Tighten:
lPinch bolt (upper bracket) 1
lPinch bolt (lower bracket) 2
CAUTION:
Tighten the lower bracket to specified
torque. If torqued too much, it may cause
the front fork to malfunction.
5. Install:
lBrake hose holder 1
lBrake caliper 2
lBolt (brake caliper) 3
NOTE:
Fit the brake hose holder cut a over the pro-
jection b on the front fork and clamp the brake
hose.
6. Install:
lBrake hose holder 1
lBolt (brake hose holder) 2
lProtector 3
lBolt (protector) 4
NOTE:
When installing the brake hose holder, pass
the brake hose 5 in front of the axle boss a,
then fit it into the hose groove b so that the
brake hose does not contact the nut (wheel
axle).
T R..23 Nm (2.3 m · kg, 17 ft · lb)
T R..20 Nm (2.0 m · kg, 14 ft · lb)
T R..23 Nm (2.3 m · kg, 17 ft · lb)
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)
7. Adjust:
lRebound damping force
NOTE:
Turn in the damping adjuster 1 finger-tight
and then turn out to the originally set position.