2001 YAMAHA WR 250F clutch

3 - 46
INSP
ADJ
LUBRICATION
LUBRICATION
To ensure smooth operation of all compo-
nents, lubricate your machine during setup,
after break-in, and after every race.
1All control cable
2Clutch lever pivot
3Shift pedal pivot
4Footrest pivot
5Throttle-to-handlebar contact
6Drive chain
7Tube guide cable winding portion
8Throttle cable end
9Clutch cable end
0Decompression cable endUse Yamaha cable lube or equivalent on these
areas.
õUse SAE 10W-30 motor oil or suitable chain
lubricants.
‚Lubricate the following areas with high quality,
lightweight lithium-soap base grease.
CAUTION:
Wipe off any excess grease, and avoid get-
ting grease on the brake discs.
AAA
AAB
CC

4 - 49
ENGCLUTCH
EC4A0000
CLUTCH
Extent of removal:1 Push rod 1, 2 and push lever shaft removal2 Push pod 1 disassembly
3 Friction plate and clutch plate removal4 Primary driven gear removal
Extent of removal Order Part name Q’ty Remarks
CLUTCH REMOVAL
Preparation for removal Drain the engine oil. Refer to “ENGINE OIL REPLACEMENT”
section in the CHAPTER 3.
Brake pedal Refer to “ENGINE REMOVAL” section.
Clutch cable Disconnect at engine side.
1 Clutch cover 1
2 Clutch spring 5
3 Pressure plate 1
4 Push rod 1 1
5 Circlip 1
6 Washer 1
7 Bearing 1
8 Ball 1
9Push rod 2
1
4
1
12
3

4 - 50
ENGCLUTCH
Extent of removal Order Part name Q’ty Remarks
10 Friction plate 9
11 Clutch plate 8
12 Cushion spring 1
13 Seat plate 1
14 Nut (clutch boss) 1
Use special tool.
Refer to “REMOVAL POINTS”. 15 Look washer 1
16 Clutch boss 1
17 Thrust washer 1
18 Primary driven gear 1
19Push lever shaft
1
4
1
3

4 - 51
ENGCLUTCH
EC4A3000
REMOVAL POINTS
Clutch boss
1. Remove:
lNut 1
lLock washer 2
lClutch boss 3
NOTE:
Straighten the lock washer tab and use the
clutch holding tool 4 to hold the clutch boss.
For USA and CDN
õExcept for USA and CDN
Clutch holding tool:
YM-91042/90890-04086
õ
EC4A4000
INSPECTION
EC484100
Clutch housing and boss
1. Inspect:
lClutch housing 1
Cracks/wear/damage ® Replace.
lClutch boss 2
Scoring/wear/damage ® Replace.
EC484201
Primary driven gear
1. Check:
lCircumferential play
Free play exists ® Replace.
lGear teeth a
Wear/damage ® Replace.
Clutch spring
1. Measure:
lClutch spring free length a
Out of specification ® Replace springs
as a set.
Clutch spring free length:
39.1 mm (1.54 in)
: 38.1 mm (1.50 in)

4 - 52
ENGCLUTCH
Friction plate
1. Measure:
lFriction plate thickness
Out of specification ® Replace friction
plate as a set.
Measure at all four points.
EC484600
Clutch plate
1. Measure:
lClutch plate warpage
Out of specification ® Replace clutch
plate as a set.
Use a surface plate 1 and thickness
gauge 2.
Friction plate thickness:
2.9 ~ 3.1 mm
(0.114 ~ 0.122 in)
: 2.7 mm (0.106 in)
Warp limit:
0.1 mm (0.004 in)
Push lever shaft
1. Inspect:
lPush lever shaft 1
Wear/damage ® Replace.
Push rod
1. Inspect:
lPush rod 1 1
lBearing 2
lWasher 3
lPush rod 2 4
lBall 5
Wear/damage/bend ® Replace.

4 - 53
ENGCLUTCH
EC4A5000
ASSEMBLY AND INSTALLATION
Push lever shaft
1. Install:
lPush lever shaft 1
lBolt (push lever shaft) 2
NOTE:
lApply the lithium soap base grease on the oil
seal lip.
lApply the engine oil on the push lever shaft.
lFit the seat plate 3 in the groove a of the
push lever shaft and tighten the bolt (seat
plate).
3
1
a2
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)
Clutch
1. Install:
lPrimary driven gear 1
lThrust washer 2
lClutch boss 3
NOTE:
Apply the engine oil on the primary driven gear
inner circumference.
2. Install:
lLock washer 1
lNut (clutch boss) 2
NOTE:
Use the clutch holding tool 3 to hold the clutch
boss.
For USA and CDN
õExcept for USA and CDN
Clutch holding tool:
YM-91042/90890-04086
T R..60 Nm (6.0 m · kg, 43 ft · lb)

õ

4 - 54
ENGCLUTCH
3. Bend the lock washer 1 tab.
4. Install:
lSeat plate 1
lCushion spring 2
NOTE:
lInstall the seat plate with its chamfered por-
tion a facing the clutch boss 3.
lInstall the cushion spring with the paint b
facing out.
1
2 1
2 3
a
b
5. Install:
lFriction plate 1 1
lClutch plate 1 2
lFriction plate 2 3
lClutch plate 2 4
NOTE:
lInstall the clutch plates and friction plates
alternately on the clutch boss, starting with a
friction plate and ending with a friction plate.
lUse the friction plates 1 for the first and final
while paying attention to the difference in
surface pattern.
lApply the engine oil on the friction plates and
clutch plates.
lUnlike the clutch plate 2, the clutch plate 1
has no surface gloss. Use the clutch plate 1
for the first while paying attention to the dif-
ference in surface gloss.
1
2
6. Install:
lBearing 1
lWasher 2
lCirclip 3
To push rod 1 4.
NOTE:
Apply the engine oil on the bearing and
washer.

4 - 55
ENGCLUTCH
7. Install:
lPush rod 2 1
lBall 2
lPush rod 1 3
NOTE:
Apply the engine oil on the push rod 1, 2 and
ball.
8. Install:
lPressure plate 1
9. Install:
lClutch spring 1
lBolt (clutch spring) 2
NOTE:
Tighten the bolts in stage, using a crisscross
pattern.
T R..8 Nm (0.8 m · kg, 5.8 ft · lb)
10. Install:
lDowel pin 1
lGasket (clutch cover) 2
11. Install:
lClutch cover 1
lBolt (clutch cover)
NOTE:
Tighten the bolts in stage, using a crisscross
pattern.
T R..10 Nm (1.0 m · kg, 7.2 ft · lb)