Page 17 of 88
3-5
INSTRUMENT AND CONTROL FUNCTIONS
1
23
4
5
6
7
8
9
EAU00162
Brake pedalThe brake pedal is on the right side
of the motorcycle. To apply the rear
brake, press down on the brake
pedal.1. Brake pedal
EAU01498
Fuel tank capTo open the fuel tank cap
1. Insert the key into the lock and
turn it 1/4 turn counterclockwise.
2. Turn the fuel tank cap counter-
clockwise, and then pull it off.1. Fuel tank cap
a. Unlock
b. Open
To close the fuel tank cap
1. Insert the fuel tank cap into the
tank opening with the key insert-
ed in the lock, and then turn the
cap clockwise.
2. Turn the key clockwise to the
original position, and then
remove it.NOTE:
The fuel tank cap cannot be installed
unless the key is in the lock. In addi-
tion, the key cannot be removed if the
cap is not properly installed and
locked.
EWA00025
wMake sure that the fuel tank cap is
properly closed before riding.
1
1
a
b
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 15
Page 20 of 88

3-8
INSTRUMENT AND CONTROL FUNCTIONS
1
23
4
5
6
7
8
9
EAU03032
Starter (choke) knob Ò1ÓStarting a cold engine requires a rich-
er air-fuel mixture, which is supplied
by the starter (choke).
Move the knob in direction ato turn
on the starter (choke).
Move the knob in direction bto turn
off the starter (choke).1. Starter (choke) knob Ò1Ó
EAU02934
Steering lockTo lock the steering
1. Turn the handlebar all the way to
the right.
2. Open the steering lock cover,
and then insert the key.
3. Turn the key 1/8 turn counter-
clockwise, push it in while turning
the handlebar slightly to the left,
and then turn the key 1/8 turn
clockwise.
4. Check that the steering is locked,
remove the key, and then close
the lock cover.1. Steering lock
2. Cover
To unlock the steering
1. Open the steering lock cover,
and then insert the key.
2. Push the key in, turn it 1/8 turn
counterclockwise so that it
moves out, and then release it.
3. Remove the key, and then close
the lock cover.
a
b
1
12
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 18
Page 66 of 88
6-35
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
94. Remove the headlight bulb hold-
er by turning it counterclockwise,
and then remove the defective
bulb.
EW000119
wHeadlight bulbs get very hot.
Therefore, keep flammable prod-
ucts away from a lit headlight bulb,
and do not touch the bulb until it
has cooled down.5. Place a new bulb into position,
and then secure it with the bulb
holder.1. Headlight bulb holder
1
3. Disconnect the headlight cou-
pler, and then remove the head-
light bulb cover.1. Coupler
2. Headlight bulb cover
1
2
EAU01158
Replacing the headlight bulbIf the headlight bulb burns out,
replace it as follows.
1. Remove cowling A. (See page
6-5 for cowling removal and
installation procedures.)
2. Remove the headlight unit by
removing the bolts.1. Bolt (´2)
1
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 64
Page 67 of 88
6-36
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9 6. Install the bulb cover, and then
connect the coupler.
7. Install the headlight unit by
installing the bolts.
8. Install the cowling.
9. Have a Yamaha dealer adjust
the headlight beam if necessary.
EAU03497
Replacing a turn signal light
bulb1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.1. Screw
2. Lens
3. bulb
1
2
3
ECA00065
cCDo not overtighten the screw, oth-
erwise the lens may break.
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 65
Page 68 of 88

6-37
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
56
7
8
9
EAU01579
Supporting the motorcycleSince this model is not equipped with
a centerstand, follow these precau-
tions when removing the front and
rear wheel or performing other main-
tenance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed
under the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcy-
cle by using a motorcycle stand
or, if an additional motorcycle
stand is not available, by placing
a jack under the frame in front of
the rear wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand. 2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
cCDo not overtighten the screws,
otherwise the lens may break.1. Bulb
1
EAU01623
Replacing the tail/brake light
bulb1. Remove the tail/brake light lens
by removing the screws.1. Screw (´2)
1
5EK-9-E2 (TW125)<3.3Passport> 5/23/00 9:47 AM Page 66