2001 YAMAHA TTR125 ignition

6 - 1
–+ELEC

* The illustration shows the TT-R125LW
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC600000
ELECTRICAL
EC610000
ELECTRICAL COMPONENTS AND WIRING DIAGRAM
EC611000
ELECTRICAL COMPONENTS
1
CDI unit
2
Engine stop switch
3
Ignition coil
4
CDI magneto
5
Spark plug
COLOR CODE
B.......................Black
Br .....................Brown
G ......................Green
O ......................Orange
R ......................Red
W......................WhiteB/R .................. Black/Red
B/W ................. Black/White
G/L .................. Green/Blue
G/W ................. Green/White
W/L .................. White/Blue
W/R ................. White/Red
EC612000
WIRING DIAGRAM
6

6 - 2
–+ELEC

IGNITION SYSTEM
EC620000
IGNITION SYSTEM
INSPECTION STEPS
Use the following steps for checking the possibility of the malfunctioning engine being attributable to
ignition system failure and for checking the spark plug which will not spark.
*marked: Only when the ignition checker is used.
NOTE:

l
Remove the following parts before inspection.
1) Seat
2) Fuel tank
l
Use the following special tools in this inspection.
Spark gap test*Clean or replace
spark plug.
Check entire ignition
system for connection.Repair or replace.
Check engine stop switch. Replace.
Check ignition coil. Primary coil Replace.
Secondary coilReplace.
Check CDI magneto. Pickup coil Replace.
Charging coil Replace.
Replace CDI unit.
Dynamic spark tester:
YM-34487
Ignition checker:
90890-06754
Pocket tester:
YU-3112-C/90890-03112
No Spark
OK
OK
OK
OK
Spark
No good
No good
No good
No good
No good
No good

6 - 3
–+ELEC

IGNITION SYSTEM
SPARK GAP TEST
1. Disconnect the spark plug cap from spark
plug.
2. Connect the dynamic spark tester
1
(ignition checker
2
) as shown.
l
Spark plug cap
3

l
Spark plug
4


For USA and CDN
õ
Except for USA and CDN
3. Kick the kickstarter crank.
4. Check the ignition spark gap.
5. Start engine, and increase spark gap
until misfire occurs. (for USA and CDN
only)
Minimum spark gap:
6.0 mm (0.24 in)

õ

EC624000
COUPLERS AND LEADS CONNECTION
INSPECTION
1. Check:
l
Couplers and leads connection
Rust/dust/looseness/short-circuit
®

Repair or replace.
ENGINE STOP SWITCH INSPECTION
1. Inspect:
l
Engine stop switch conduct.
Not continuous while being pushed
®

Replace.
Continuous while being freed
®
Replace.
Tester (+) lead
®
Black/White lead
1

Tester (–) lead
®
Black lead
2

B/W
1
B
2
Tester selec-
tor position
PUSH IN
W

´
1
FREE

6 - 4
–+ELEC

IGNITION SYSTEM
EC626002
IGNITION COIL INSPECTION
1. Inspect:
l
Primary coil resistance
Out of specification
®
Replace.
Tester (+) lead
®
Orange lead
1

Tester (–) lead
®
Black lead
2

Primary coil
resistanceTester selector
position
0.18 ~ 0.28
W
at
20 ˚C (68 ˚F)
W

´
1
2. Inspect:
l
Secondary coil resistance
Out of specification
®
Replace.
NOTE:

When inspecting the secondary coil resis-
tance, remove the spark plug cap.
Tester (+) lead
®
Spark plug lead
1

Tester (–) lead
®
Orange lead
2

Secondary coil
resistanceTester selector
position
6.3 ~ 9.5 k
W
at
20 ˚C (68 ˚F)k
W

´
1

6 - 5
–+ELEC

IGNITION SYSTEM
CDI MAGNETO INSPECTION
1. Inspect:
l
Pickup coil resistance
Out of specification ® Replace.
Tester (+) lead ® Red lead 1
Tester (–) lead ® White lead 2
Pickup coil
resistanceTester selector
position
248 ~ 372 W at
20 ˚C (68 ˚F)W ´ 100
2. Inspect:
lCharging coil resistance
Out of specification ® Replace.
Tester (+) lead ® Brown lead 1
Tester (–) lead ® Green lead 2
Charging coil
resistanceTester selector
position
688 ~ 1,032 W
at 20 ˚C (68 ˚F)W ´ 100
EC628000
CDI UNIT INSPECTION
Check all electrical components. If no fault is
found, replace the CDI unit. Then check the
electrical components again.