2001 TOYOTA TUNDRA four wheel drive

'01 TUNDRA_U (L/O 0008)
82001 TUNDRA (OM 34416U)
*
1: For details, see ªService reminder indicators and warning
buzzersº in Section 1±5.
*2: If this light flashes, see ªFour±wheel drive systemº in Sec-
tion 1±6.
*3: If this light flashes, see ªCruise controlº in Section 1±6. Cruise control indicator light
*
3
Low speed four±wheel drive indicator light*2
Four±wheel drive indicator light
High speed four±wheel drive indicator light
*2
Automatic transmission indicator lights
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
902001 TUNDRA (OM 34416U)
Do this.
If the indicator or
buzzer comes on...
(g) Fill up tank.
(f) Take vehicle to
Toyota dealer.
(h) Take vehicle to
Toyota dealer.
or
(i) Close all doors.
(j)Take vehicle to
To y o t a
dealer
immediately.
Do this.
If the indicator or
buzzer comes on...
(k) Shift front drive control lever out of
ªNº.
(l)Stop and check.
(m) Add washer fluid.
(n)Remove key.
Key reminder
buzzer
(o) Shift the transfer
mode again,
correctly.
Four±wheel
drive system
warning
buzzer (a) Brake System Warning Light
This light comes on in the following cases
when the ignition key is in the ªONº posi-
tion.

When the parking brake is applied...

When the brake fluid level is low...
CAUTION
It is dangerous to continue driving
normally when the brake fluid level is
low.
Have your vehicle checked at your
Toyota dealer in the following case:

The light does not come on even if the
parking brake is applied when the igni-
tion key is in the ªONº position.
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
932001 TUNDRA (OM 34416U)
(k) Unengaged ªParkº Warning Light
(with automatic transmission and
front drive control lever)
This light warns that the transmission
ªParkº mechanism is not engaged. If the
front drive control lever is in the ªNº posi-
tion while the selector lever is in the ªPº
position, the transmission will disengage
and the wheels will not lock.
CAUTION
To restore the park function, shift the
front drive control lever out of ªNº,
or the vehicle can move.
(l) Automatic Transmission Fluid Tem- perature Warning Light
This light warns that the automatic trans-
mission fluid temperature is too high.
If this light comes on while you are driv-
ing, slow down and pull off the road. Stop
the vehicle at a safe place and put the
selector lever in ªPº. With the engine id-
ling, wait until the light goes off. If the
light goes off, you may start the vehicle
again. If the light does not go off, call a
Toyota dealer or qualified repair shop for
assistance. (m) Low Windshield Washer Fluid Level
Warning Light (with daytime running
light system)
This light warns that the windshield wash-
er fluid level is too low. Add washer fluid
at your earliest opportunity. (For instruc-
tions, see ªAdding washer fluidº in Section
7±3.)
(n) Key Reminder Buzzer
This buzzer reminds you to remove the
key when you open the driver 's door with
the ignition key in the ªACCº or ªLOCKº
position.
(o) Four±wheel drive system warning buzzer
This buzzer reminds you that the transfer
mode is not selected correctly.
If the buzzer sounds when you shift the
transfer from ª2WDº to ª4HIº, ª4LOº to
ª4HIº, ª4HIº to ª4LOº, or ª4LOº to ª2WDº
mode, follow the instructions in ªFour±
wheel drive systemº in Section 1±6. CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light and low windshield
washer fluid level warning light)
1. Apply the parking brake.
2. Open one of the doors. The open door warning light should
come on.
3. Close the door. The open door warning light should go
off.
4. Turn the ignition key to ªACCº. The SRS warning light should come on.
It goes off after about 6 seconds.
5. Turn the ignition key to ªONº, but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light and
SRS warning light should come on. The
ªABSº warning light goes off after a
few seconds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by your Toyota
dealer as soon as possible.
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
952001 TUNDRA (OM 34416U)
OPERATION OF INSTRUMENTS AND
CONTROLS
Ignition switch, Transmission and Parking brake
Ignition switch with steering lock 96
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic transmission 97
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. .
Manual transmission 101
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . .
Four±wheel drive system 103
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
Parking brake 108
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Cruise control 108
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . . . .
Clutch start cancel switch 111
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
SECTION 1± 6
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
982001 TUNDRA (OM 34416U)
(b) Overdrive switch
You can select either third gear (with
overdrive off) or fourth gear (with over-
drive on) by pushing this switch.
To turn the overdrive off, push the switch.
The ªO/D OFFº indicator light should come
on. To turn the overdrive on again, push
the switch again. The ªO/D OFFº indicator
light should go off.
Always drive your vehicle with the over-
drive on for better fuel economy and
quieter driving.
If the engine is turned off when the over-
drive is off and restarted, the overdrive
will automatically be on. Vehicles with cruise controlÐWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be enabled because the
cruise control is not cancelled.
For ways to decrease the vehicle speed,
see ªCruise controlº in this section.
(c) Normal driving
1. Start the engine as instructed in ªHow to start the engineº in Section 3. The
transmission must be in ªPº or ªNº.
2. With your foot holding down the brake pedal, shift the selector lever to ªDº.
When the lever is in the ªDº position, the
automatic transmission system will select
the most suitable gear for running condi-
tions such as normal cruising, hill climb-
ing, hard towing, etc.
Always turn the overdrive on for better
fuel economy and quieter driving. If the
engine coolant temperature is low, the
transmission will not shift into the over-
drive gear even with the overdrive on.
CAUTION
Never put your foot on the accelera-
tor pedal while shifting.
3. Release the parking brake and brake pedal. Depress the accelerator pedal
slowly for smooth starting.
(d) Using engine braking
To use engine braking, you can downshift
the transmission as follows:

Push the overdrive switch. The ªO/D
OFFº indicator light will come on and
the transmission will downshift to third
gear.

Shift into the ª2º position. The trans-
mission will downshift to second gear
when the vehicle speed drops down to
or lower than the following speed, and
stronger engine braking will be en-
abled.
Two±wheel drive models
5VZ±FE engine 115 km/h (71 mph)
2UZ±FE engine 120 km/h (75 mph)
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
992001 TUNDRA (OM 34416U)
Four±wheel drive models
5VZ±FE engine Front drive control lever in ªH2º or
ªH4º 109 km/h (68 mph)
Front drive control lever in ªL4º
37 km/h (23 mph)
2UZ±FE engine ª2WDº or ª4HIº mode is selected 120 km/h (75 mph)
ª4LOº mode is selected
41 km/h (25 mph)

Shift into the ªLº position. The trans-
mission will downshift to first gear
when the vehicle speed drops down to
or lower than the following speed, and
maximum engine braking will be en-
abled.
Two±wheel drive models
5VZ±FE engine 55 km/h (34 mph)
2UZ±FE engine 58 km/h (36 mph) Four±wheel drive models
5VZ±FE engine Front drive control lever in ªH2º or
ªH4º 52 km/h (32 mph)
Front drive control lever in ªL4º
10 km/h (6 mph)
2UZ±FE engine ª2WDº or ª4HIº mode is selected 58 km/h (36 mph)
ª4LOº mode is selected
11 km/h (7 mph)
Vehicles with cruise controlÐWhen the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking is not enabled because the cruise
control is not cancelled.
For ways to decrease the vehicle speed,
see ªCruise controlº in this section.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
(e) Using ª2º and ªLº positions
The ª2º and ªLº positions are used for
strong engine braking as described pre-
viously.
With the selector lever in ª2º or ªLº, you
can start the vehicle in motion as with the
lever in ªDº.
With the selector lever in ª2º, the vehicle
will start in first gear and automatically
shift to second gear.
With the selector lever in ªLº, the trans-
mission is engaged in first gear.
NOTICE
Be careful not to over±rev the en- gine. Watch the tachometer to keepengine rpm from going into the redzone. The approximate maximum al-
lowable speed for each position isgiven below for your reference:
Two±wheel drive models
5VZ±FE engineЪ2º 115 km/h (71 mph) . . . . . . . . .
ªLº 60 km/h (37 mph) . . . . . . . . . .
2UZ±FE engineÐ ª2º 120 km/h (75 mph) . . . . . . . . .
ªLº 65 km/h (40 mph) . . . . . . . . . .
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
1002001 TUNDRA (OM 34416U)
Four±wheel drive models
5VZ±FE engineÐFront control lever in ªH2º orªH4º
ª2º 110 km/h (68 mph) . . . . . . . . .
ªLº 60 km/h (37 mph)
. . . . . . . . . .
Front control lever in ªL4º
ª2º 40 km/h (25 mph)
. . . . . . . . . .
ªLº 20 km/h (12 mph)
. . . . . . . . . .
2UZ±FE engineÐ ª2WDº or ª4HIº mode is selected ª2º 120 km/h (75 mph)
. . . . . . . . .
ªLº 65 km/h (40 mph)
. . . . . . . . . .
ª4LOº mode is selected ª2º 45 km/h (28 mph)
. . . . . . . . . .
ªLº 25 km/h (16 mph)
. . . . . . . . . .
Do not continue hill climbing or
hard towing for a long time in theª2º or ªLº position. This may causesevere automatic transmission dam-
age from overheating. To preventsuch damage, ªDº position shouldbe used in hill climbing or hard
towing.
(f) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down with your foot, shift the selector lever to the
ªRº position.
NOTICE
Never shift into reverse while the ve-
hicle is moving.
(g) Parking
1. Bring the vehicle to a complete stop.
2. With the brake pedal pressed down, fully depress the parking brake pedal
to apply the parking brake securely.
3. With the brake pedal pressed down, shift the selector lever to the ªPº posi-
tion.
CAUTION
Never attempt to move the selector
lever into ªPº position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.
(h) Good driving practice

If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.
CAUTION
Always keep your foot on the brake
pedal while stopped with the engine
running. This prevents the vehicle
from creeping.
NOTICE
Do not hold the vehicle on an up-grade with the accelerator pedal. Itcan cause the transmission to over-heat. Always use the brake pedal or
parking brake.
ProCarManuals.com

'01 TUNDRA_U (L/O 0008)
1022001 TUNDRA (OM 34416U)
Recommended shifting speeds
The transmission is fully synchronized and
upshifting or downshifting is easy.
For the best compromise between fuel
economy and vehicle performance, you
should upshift or downshift at the following
speeds:
gear km/h (mph)
1 to 2 or 2 to 1 24 (15)
2 to 3 or 3 to 2 40 (25)
3 to 4 or 4 to 3 64 (40)
4 to 5 or 5 to 4 72 (45)
Downshift to the appropriate gear if accel-
eration is needed when you are cruising
below the above downshifting speeds.
Upshifting too soon or downshifting too
late will cause lugging, and possibly ping-
ing. Regularly revving the engine to maxi-
mum speed in each gear will cause ex-
cessive engine wear and high fuel
consumption. Maximum allowable speeds
To get on a highway or to pass slower
traffic, maximum acceleration may be nec-
essary. Make sure you observe the follow-
ing maximum allowable speeds in each
gear:
Two±wheel drive models
gear km/h (mph)
1 45 (28)
2 85 (53)
3 125 (78)
4 165 (112)
Four±wheel drive models gear km/h (mph) ªH2º or ªH4º ªL4º
1 45 (28) 15 (9)
2 85 (53) 30 (18)
3 125 (78) 45 (28)
4 165 (103) 70 (43)
NOTICE
Do not downshift if you are going
faster than the maximum allowablespeed for the next lower gear.
Good driving practice

If it is difficult to shift into reverse, put
the transmission in neutral, release the
clutch pedal momentarily, and then try
again.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use fifth gear.
CAUTION
Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to spin or
skid.
NOTICE
Make sure the vehicle is completely
stopped before shifting into reverse.
ProCarManuals.com