2001 TOYOTA TACOMA reset

’01 Tacoma U (L/O 0009)
42001 TACOMA (OM35766U)
1. Engine coolant temperature gauge
2. Tachometer
3. Service reminder indicators and indicator lights 4. Speedometer
5. Fuel gauge
6. Trip meter reset knob
7. Odometer and two trip meters
Instrument cluster overview

With tachometer

’01 Tacoma U (L/O 0009)
11 62001 TACOMA (OM35766U)
Odometer and two trip meters
This meter displays the odometer and
two trip meters.1. OdometerShows the total distance the vehicle has been driven.
2. Two trip metersShow two different distances independently driven since
the last time each trip meter was set
to zero.
You can use one trip meter to calculate
the fuel economy and the other to
measure the distance on each trip. All
trip meter data is cancelled if the elec-
trical power source is disconnected. 3. Trip meter reset knobResets the two
trip meters to zero, and also change
the meter display.
To change the meter display, quickly
push and release the knob. The meter
display changes in the order from the
odometer to trip meter A to trip meter
B, then back to the odometer each
time you push.
To reset the trip meter A to zero, dis-
play the meter A reading, then push
and hold the knob until the meter is
set to zero. The same process can be
applied for resetting the trip meter B.
(d) Stop and check.
(a)
If parking brake is
off, stop
immediately and
contact Toyota
dealer.
(b) Fasten seat belt.
(c) Stop and check.
(e) Take vehicle to
Toyota dealer.
(indicator and buzzer)
If the indicator or
buzzer comes on...
Do this.
Service reminder indicators
an d warn in g bu zzers

’01 Tacoma U (L/O 0009)
1332001 TACOMA (OM35766U)
SHIFTING BETWEEN H2" AND H4"
To shift from H2" to H4", reduce your
speed to less than 80 km/h (50 mph) and
move the front drive control lever.
If you have trouble shifting in cold weath-
er, reduce your speed or stop the vehicle
and reshift.
CAUTION
Never move the front drive control
lever if wheels are slipping. Stop the
slipping or spinning before shifting.
To shift from H4" to H2", simply move
the front drive control lever.
This can be done at any vehicle speed.
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse.
SHIFTING BETWEEN H4" AND L4"
To shift between H4" and L4", stop
the vehicle and put the transmission in
N". With your foot holding down the
brake pedal, move the front drive control
lever. SHIFTING BETWEEN H2" AND H4"
To shift from H2" to H4",
reduce your
speed to less than 100 km/h (62 mph)
and push in the 4WD" button. You need
not depress the clutch pedal.
If the indicator light does not come on
when you push in the 4WD" button, drive
straight ahead while accelerating or decel-
erating.
If the indicator light flashes and the buzz-
er sounds when you push in the 4WD"
button, reduce your speed or stop the
vehicle and reset.CAUTION
Never push the 4WD" button if
wheels are slipping. Stop the slipping
or spinning before shifting.
To shift from H4" to H2", push the
4WD" button again to turn it off.
This can be done at any vehicle speed.
You need not depress the clutch pedal.
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse. SHIFTING BETWEEN H2" OR H4" AND
L4"
To shift from H2" or H4" to L4",
stop the vehicle or reduce your speed to
less than 8 km/h (5 mph). With your foot
off the accelerator pedal, depress the
clutch pedal and move the front drive con-
trol lever.
To shift from L4" to H2" or H4",
depress the clutch pedal and move the
front drive control lever. When the 4WD"
button is pushed in, the transfer shifts into
H4"; when the button is left out, the
transfer shifts into H2".
This can be done at any vehicle speed.
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse.
(c) Shifting procedure
(lever type with automatic
transmission)
(c) Shifting procedure
(lever/button type with manual
transmission)

’01 Tacoma U (L/O 0009)
1342001 TACOMA (OM35766U)
SHIFTING BETWEEN H2" AND H4"
To shift from H2" to H4", reduce your
speed to less than 100 km/h (62 mph)
and push in the 4WD" button.
If the indicator light does not come on
when you push in the 4WD" button, drive
straight ahead while accelerating or decel-
erating.
If the indicator light flashes and the buzz-
er sounds when you push in the 4WD"
button, reduce your speed or stop the
vehicle and reset.
CAUTION
Never push the 4WD" button if
wheels are slipping. Stop the slipping
or spinning before shifting.
To shift from H4" to H2", push the
4WD" button again to turn it off.
This can be done at any vehicle speed.
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse. SHIFTING BETWEEN H2" OR H4" AND
L4"
To shift from H2" or H4" to L4",
stop the vehicle and put the transmission
in N". With your foot holding down the
brake pedal, move the front drive control
lever.
To shift from L4" to H2" or H4",
stop the vehicle and put the transmission
in N". With your foot holding down the
brake pedal, move the front drive control
lever. When the 4WD" button is pushed
in, the transfer shifts into H4"; when the
button is left out, the transfer shifts into
H2".
If the indicator light does not go off when
you shift the transfer into H2", drive
straight ahead while accelerating or decel-
erating, or drive in reverse.
Rear differential lock system
The rear differential lock system is pro-
vided for use only when wheel spinning
occurs in a ditch or on a slippery or
ragged surface.
This differential lock system is effective in
case one of the rear wheels is spinning.
Except for Pre Runner models
⎯
Before using the rear differential lock sys-
tem, first shift the front drive control into
L4" to see if it works. If this has no
effect, additionally use the rear differential
lock system.
(c) Shifting procedure
(lever/button type with
automatic transmission)

’01 Tacoma U (L/O 0009)
1382001 TACOMA (OM35766U)
If you need accelerationfor example,
when passingdepress the accelerator
pedal enough for the vehicle to exceed
the set speed. When you release it, the
vehicle will return to the speed set prior
to the acceleration.
CAUTION
For manual transmission:
While driving with the cruise control
on, do not shift to neutral without
depressing the clutch pedal, as this
may cause engine racing or over−rev-
ving.
CANCELLING THE PRESET SPEED
You can cancel the preset speed by:
a. Pulling the lever in the CANCEL"direction and releasing it
b. Depressing the brake pedal
c. Depressing the clutch pedal (manual
transmission)
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out. If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.
RESETTING TO A FASTER SPEED
Push the lever up in the RES/ACC" direc-
tion and hold it. Release the lever when
the desired speed is attained. While the
lever is held up, the vehicle will gradually
gain speed.
However, a faster way to reset is to ac-
celerate the vehicle and then push the
lever down in the SET/COAST" direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the SET/COAST"
direction and hold it. Release the lever
when the desired speed is attained. While
the lever is held down, the vehicle speed
will gradually decrease.
However, a faster way to reset is to de-
press the brake pedal and then push the
lever down in the SET/COAST" direction.
On vehicles with automatic transmission,
even if you turn off the overdrive switch
with the cruise control on, engine braking
will not be applied because the cruise
control is not cancelled. To decrease the
vehicle speed, reset to a slower speed
with the cruise control lever or depress
the brake pedal. If you use the brake
pedal, cruise control is cancelled.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by pulling
the control lever or by depressing the
brake pedal or clutch pedal, pushing the
lever up in the RES/ACC" direction will
restore the speed set prior to cancellation.
However, once the vehicle speed falls be-
low about 40 km/h (25 mph), the preset
speed will not be resumed.

’01 Tacoma U (L/O 0009)
1452001 TACOMA (OM35766U)
1 2 3 4 5 6 (Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in
the desired station (see TUNE" knob or
SEEK" button). Push and hold down the
button until you hear a beepthis will set
the station to the button. The button num-
ber will appear on the display.
To tune in to a preset station: Push the
button for the station you want. The but-
ton number and station frequency will ap-
pear on the display.
These systems can store one AM and two
FM stations for each button (The display
will show AM", FM1" or FM2" when you
push AM" FM1·2").
(Program)
Push 
" to select the other side of a
cassette tape. The display indicates which
side is currently selected (
" indicates
top side, 
" indicates bottom side).
Auto−reverse feature: After the cassette
player reaches the end of a tape side, it
automatically reverses and begins to play
the other side. This is true whether the
cassette was playing or fast forwarding.
(Reverse/Fast forward buttons)
Cassette Player
Push the fast forward button to fast for-
ward a cassette tape. FF" will appear on
the display. Push the reverse button to
rewind a tape. REW" will appear on the
display.
To stop the tape while it is fast forward-
ing, push the fast forward button or
TAPE"; to stop the tape while it is re-
winding, push the reverse button or
TAPE".
If a tape side rewinds completely, the cas-
sette player will stop and then play that
same side. If a tape fast forwards com-
pletely, the cassette player will play the
other side of the tape, using the auto−re-
verse feature.
Compact Disc Player
If you want to fast forward or reverse
through a compact disc track, push and
hold in the fast forward or reverse button.
When you release the button, the compact
disc player will resume playing. AM
Push AM" to turn on the radio and select
the AM band. AM" will appear on the
display.
If the audio system is off, you can turn
on the radio by pushing AM". Also, push
AM" to switch from cassette or compact
disc operation to radio operation.
CTRL / MODE (Audio control and mode
adjustment)
Manual tone adjustment function
This knob is used to adjust the tone
manually.
For low−pitch tone adjustment, push
CTRL / MODE" repeatedly until BAS"
appears on the display. Then turn the
knob to suit your preference.
The display will show the range from
BAS −5" to BAS 5".
For high−pitch tone adjustment, push
CTRL / MODE" repeatedly until TRE"
appears on the display. Then turn the
knob to suit your preference.
The display will show the range from
TRE −5" to TRE 5".

’01 Tacoma U (L/O 0009)
1482001 TACOMA (OM35766U)
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold SCAN" until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
SCAN" again.
To scan all the frequencies:
Quickly push and release SCAN". If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push SCAN" again.
Compact disc player
There are two scan featuresyou can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.Scanning the tracks on a disc:
Quickly push and release SCAN". SCAN"
will appear on the display and the player
will scan all the tracks on the disc you
are listening to. If you hear a beep, you
held the button too long, and the player
will scan the first track of all the discs in
the magazine. To select a track, push
SCAN" again. If the player scanned all
the tracks on the disc, it will stop scan-
ning.
Compact disc auto changer only
Scanning the first track of all the discs in
the magazine:
Push SCAN" until you hear a beep.

·SCAN" will appear on the display
and the player will perform the first track
of the next disc. To select a disc, push
the SCAN" again. If the player has
scanned all the di scs, it will stop scan-
ning.
SEEK (Seeking)
Radio
In the seek mode, the radio finds and
plays the next station up or down the
station band.
To seek a station, quickly push and re-
lease the  " or  " under the SEEK".
Do this again to find another station. Cassette Player
By using this button, you can skip up or
down to a different track.
You can skip up to nine tracks at a time.
Push the up or down side of the button.
FF 1" or REW 1" will appear on the
display.
Next, push either side of the track button
until the number on the display reaches
the number of tracks you want to skip. If
you push the button ten times, the skip
feature will be turned off.
When counting the number of tracks you
want to rewind, remember to count the
current track as well. For example, if you
want to rewind to a song that is two be-
fore the song you are listening to, push
on the down side of the button until REW
3" appears on the display.
If you have pushed the track button more
than you wanted to, push the other side
of the button. The track number will be
reduced.
The track number you select is not valid
if it is higher than the number of tracks
remaining on the current cassette side.
After the beginning of the tape is
reached, the player will automatically
start playing the same side.

’01 Tacoma U (L/O 0009)
1512001 TACOMA (OM35766U)
1 2 3 4 5 6 (Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in
the desired station (see TUNE" knob or
SEEK" button). Push and hold down the
button until you hear a beepthis will set
the station to the button. The button num-
ber will appear on the display.
To tune in to a preset station: Push the
button for the station you want. The but-
ton number and station frequency will ap-
pear on the display.
These systems can store one AM and two
FM stations for each button (The display
will show AM", FM1" or FM2" when you
push AM" FM1·2").
(Eject button)
Push the cassette tape eject button to
eject a cassette. Push the compact disc
eject button to eject a compact disc.
After you turn the ignition to LOCK", you
will be able to eject a cassette or disc but
you will not be able to reinsert it.
(Program)
Push 
" to select the other side of a
cassette tape. The display indicates which
side is currently selected (
" indicates
top side, 
" indicates bottom side).
Auto−reverse feature: After the cassette
player reaches the end of a tape side, it
automatically reverses and begins to play
the other side. This is true whether the
cassette was playing or fast forwarding.
(Reverse/Fast forward buttons)
Cassette Player
Push the fast forward button to fast for-
ward a cassette tape. FF" will appear on
the display. Push the reverse button to
rewind a tape. REW" will appear on the
display.
To stop the tape while it is fast forward-
ing, push the fast forward button or
TAPE"; to stop the tape while it is re-
winding, push the reverse button or
TAPE".
If a tape side rewinds completely, the cas-
sette player will stop and then play that
same side. If a tape fast forwards com-
pletely, the cassette player will play the
other side of the tape, using the auto−re-
verse feature. Compact Disc Player
If you want to fast forward or reverse
through a compact disc track, push and
hold in the fast forward or reverse button.
When you release the button, the compact
disc player will resume playing.
AM
Push AM" to turn on the radio and select
the AM band. AM" will appear on the
display.
If the audio system is off, you can turn
on the radio by pushing AM". Also, push
AM" to switch from cassette or compact
disc operation to radio operation.
CTRL / MODE (Audio control and mode
adjustment)
Manual tone adjustment function
This knob is used to adjust the tone
manually.
For low−pitch tone adjustment, push
CTRL / MODE" repeatedly until BAS"
appears on the display. Then turn the
knob to suit your preference.
The display will show the range from
BAS −5" to BAS 5".