2001 TOYOTA MR2 SPYDER wheel

01MY MR2(U) L/O 0008
1272001 MR2 (OM17482U)
Do not use your parking brake when
there is a possibility it could freeze.
When parking, put the transmission into
first or reverse and block the rear wheels.
Do not use the parking brake, or snow or
water accumulated in and around the
parking brake mechanism may freeze,
making it hard to release.
Keep ice and snow from accumulating
under the fenders.
Ice and snow built up under your fenders
can make steering difficult. During bad
winter driving, stop and check under the
fenders occasionally.
Depending on where you are driving,
we recommend you carry some emer-
gency equipment.
Some of the things you might put in the
vehicle are tire chains, window scraper,
bag of sand or salt, flares, small shovel,
jumper cables, etc.
Dinghy towing
SB31003
Your vehicle can be dinghy towed (with
four wheels on the ground) from the
front behind a motorhome.
CAUTION
Dinghy towing requires special equip-
ment and accessories. Please refer to
your service outlet of the motorhome
manufacture for the recommended
equipment.
NOTICE
Dinghy towing does not eliminate the
possibility of damage to your vehicle.
DINGHY TOWING TIPS
Before dinghy towing, be sure to ob-
serve the following in order to reduce
the damage to your vehicle.1. Put the shift lever in neutral.
2. Turn the ignition switch to the ACC" position. Make sure the audio is turned
off.
NOTICE
To avoid the locking of the steering
wheel, turn the ignition switch to the
ACC" position.
3. Release the parking brake.
After dinghy towing, let the engine idle for
more than 3 minutes before driving the
vehicle.

01MY MR2(U) L/O 0008
1292001 MR2 (OM17482U)
Avoid continuous speeding up and
slowing down. Stop−and−go driving
wastes fuel.
Avoid unnecessary stopping and
braking. Maintain a steady pace. Try
to time the traffic signals so you only
need to stop as little as possible or
take advantage of through streets to
avoid traffic lights. Keep a proper dis-
tance from other vehicles to avoid sud-
den braking. This will also reduce wear
on your brakes.
Avoid heavy traffic or traffic jams
whenever possible.
Do not rest your foot on the clutch
or brake pedal. This causes premature
wear, overheating and poor fuel econo-
my.
Maintain a moderate speed on high-
ways. The faster you drive, the greater
the fuel consumption. By reducing your
speed, you will cut down on fuel con-
sumption.
Keep the front wheels in proper
alignment. Avoid hitting the curb and
slow down on rough roads. Improper
alignment not only causes faster tire
wear but also puts an extra load on
the engine, which, in turn, wastes fuel.
Keep the bottom of your vehicle free
from mud, etc. This not only lessens
weight but also helps prevent corro-
sion.
Keep your vehicle tuned−up and in
top shape. A dirty air cleaner,
improper valve clearance, dirty plugs,
dirty oil and grease, brakes not
adjusted, etc. all lower engine
performance and contribute to poor fuel
economy. For longer life of all parts
and lower operating costs, keep all
maintenance work on schedule, and if
you often drive under severe
conditions, see that your vehicle
receives more frequent maintenance.
(For scheduled maintenance
information, please refer to the
Scheduled Maintenance Guide" or
Owner ’s Manual Supplement").
CAUTION
Never turn off the engine to coast
down hills. Your power steering and
brake booster will not function with-
out the engine running. Also, the
emission control system operates
properly only when the engine is run-
ning.

01MY MR2(U) L/O 0008
1372001 MR2 (OM17482U)
Stop the vehicle on a level firm
ground, firmly set the parking brake
and put the transmission in reverse.
Block the wheel diagonally opposite
to the one being changed if neces-
sary.
Make sure to set the jack properly
in the jack point. Raising the ve-
hicle with jack improperly posi-
tioned will damage the vehicle or
may allow the vehicle to fall off the
jack and cause personal injury.
Never get under the vehicle when
the vehicle is supported by the jack
alone.
Use the jack only for lifting your
vehicle during wheel changing.
Do not raise the vehicle with some-
one in the vehicle.
When raising the vehicle, do not
put an object on or under the jack.
Raise the vehicle only high enough
to remove and change the tire.
NOTICE
Do not continue driving with a de-
flated tire. Driving even a short dis-
tance can damage a tire and wheel
beyond repair.
SU41031
Compact spare tire
The compact spare tire is designed for
temporary emergency use only.
The compact spare tire is identified by the
distinctive wheel design and color and
special wording TEMPORARY USE ONLY"
molded into the side wall of the tire.
The standard tire should be repaired and
replaced as soon as possible.
The compact spare tire saves space in
your trunk, and its lighter weight helps to
improve fuel economy and permits easier
installation in case of a flat tire.

01MY MR2(U) L/O 0008
1392001 MR2 (OM17482U)
1. Get the tool bag and compact sparetire.
You will find a jack in the tool bag.
To prepare yourself for an emergency, you
should fam iliarize yourself with the use of
the jack, each of the tools and their stor-
age locations.
SB41047
To remove the compact spare tire:
1. Open the front box cover in the trunk.
SB41061
2. Remove the spare wheel cover.

01MY MR2(U) L/O 0008
1402001 MR2 (OM17482U)
SB41063
3. Loosen the bolt and remove it.
Then take the compact spare tire out of
the vehicle.
When storing the compact spare tire, put
it in place with the outer side of the wheel
facing up. Then secure the tire by repeat-
ing the above removal steps in reverse
order to prevent it from flying forward dur-
ing a collision or s udden braking.
SB41064
When you store the replaced flat ground
tire in the place where the compact spare
tire was loaded, install the spare wheel
extension to the spare wheel clamp.
NOTICE
The replaced ground tire should be
fixed steadily by the spare wheel
clamp or it may damage the vehicle’s
body.
Blocking the wheel
SB41035
2. Block the wheel diagonally opposite
the flat tire to keep the vehicle from
rolling when it is jacked up.
When blocking the wheel, place a wheel
block from the front for the front wheels
or from the rear for the rear wheels.

01MY MR2(U) L/O 0008
1412001 MR2 (OM17482U)
Loosening wheel nuts
SB41027
3. Loosen all the wheel nuts.
Always loosen the wheel nuts before rais-
ing the vehicle.
Turn the wheel nuts counterclockwise to
loosen. To get maximum leverage, fit the
wrench to the nut so that the handle is
on the right side, as shown above. Grab
the wrench near the end of the handle
and pull up on the handle. Be careful that
the wrench does not slip off the nut.
Do not remove the nuts yetjust unscrew
them about one−half turn.
Positioning the jack
SB41036
4. Position the jack at the correct jack point as shown.
Make sure the jack is positioned on a
level and solid place.
Raising your vehicle
SB41029
5. After making sure that no one is in the vehicle, raise it high enough so
that the compact spare tire can be
installed.
Remember you will need more ground
clearance when putting on the compact
spare tire than when removing the flat
tire.
To raise the vehicle, insert the jack handle
into the jack (it is a loose fit) and turn it
clockwise. As the jack touches the vehicle
and begins to lift, double−check that it is
properly positioned.

01MY MR2(U) L/O 0008
1422001 MR2 (OM17482U)
CAUTION
Never get under the vehicle when the
vehicle is supported by the jack
alone.
Changing wheels
SB41028
6. Remove the wheel nuts and changetires.
Lift the flat tire straight off and put it
aside.
Roll the compact spare wheel into position
and align the holes in the wheel with the
bolts. Then lift up the wheel and get at
least the top bolt started through its hole.
Wiggle the tire and press it back over the
other bolts.
SB41044
Before putting wheels on, remove any cor-
rosion on the mounting surfaces with a
wire brush or such. Installation of wheels
without good metal−to−metal contact at the
mounting surface can cause wheel nuts to
loosen and eventually cause a wheel to
come off while driving. Therefore after the
first 1600 km (1000 miles), check to see
that the wheel nuts are tight.

01MY MR2(U) L/O 0008
1432001 MR2 (OM17482U)
Reinstalling wheel nuts
SB41030
7. Reinstall all the wheel nuts with fin-ger tight.
Reinstall the wheel nuts (tapered end in-
ward) and tighten them as much as you
can by finger. Press back on the tire back
and see if you can tighten them more.
Lowering your vehicle
SB41031
8. Lower the vehicle completely and tighten the wheel nuts.
Turn the jack handle counterclockwise to
lower the vehicle.
Use only the wheel nut wrench and turn
it clockwise to tighten the nuts. Do not
use other tools or any additional leverage
other than your hands, such as a hammer,
pipe or your foot. Make sure the wrench
is securely engaged over the nut.
Tighten each nut a little at a time in the
order shown. Repeat the process until all
the nuts are tight.
CAUTION
When lowering the vehicle, make sure
all portions of your body and all oth-
er persons around will not be injured
as the vehicle is lowered to the
ground.