2001 TOYOTA AVALON wheel bolt torque

SA0VW-02
W03096
SST
W03097
WasherNut SA-14
- SUSPENSION AND AXLEFRONT WHEEL HUB BOLT
1348 Author
: Date
:
2001 AVALON (RM808U)
FRONT WHEEL HUB BOLT
REPLACEMENT
1. REMOVE FRONT WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using SST and a hammer handle or an equivalent, remove the
hub bolt.
SST 09628-1001 1
4. INSTALL HUB BOLT
(a) Install a washer and nut to a new hub bolt, as shown in the
illustration.
(b) Using a hammer handle or an equivalent to hold, install
the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 107 N´m (1,090 kgf´cm, 79 ft´lbf)
6. INSTALL FRONT WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)

SA0W6-02
R10948
Z00206
W03211
A
A
B
- SUSPENSION AND AXLEREAR AXLE HUB
SA-45
1379 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the brake caliper and disc.
Torque: 47 N´m (475 kgf´cm, 34 ft´lbf)
(b) Support the brake caliper securely.
3. CHECK BEARING BACKLASH AND AXLE HUB DEVI-
ATION
(a) Using a dial indicator, check the backlash near the center
of the axle hub.
Maximum: 0.05 mm (0.0020 in.)
If the backlash exceeds the maximum, replace the axle hub.
(b) Using a dial indicator, check the deviation at the surface
of the axle hub outside the hub bolt.
Maximum: 0.07 mm (0.0028 in.)
If the deviation exceeds the maximum, replace the axle hub.
4. DISCONNECT ABS SPEED SENSOR
Remove the bolt and disconnect the ABS speed sensor.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
5. REMOVE REAR AXLE HUB
(a) Remove the 4 bolts and rear axle hub.
Torque: 80 N´m (820 kgf´cm, 59 ft´lbf)
(b) Remove the O-ring.
HINT:
At the time of installation, coat a new O-ring with MP grease.
(c) Support the backing plate securely.
6. REMOVE REAR AXLE CARRIER
(a) Loosen the 3 nuts.
Torque:
Nut A (Reused nut): 196 N´m (2,000 kgf´cm, 145 ft´lbf)
Nut A (New nut): 255 N´m (2,600 kgf´cm, 188 ft´lbf)
Nut B: 181 N´m (1,850 kgf´cm, 134 ft´lbf)

SA0VG-02
W03216
W03217
Rear
F06465A
A B
B
- SUSPENSION AND AXLEREAR LOWER SUSPENSION ARM AND STRUT ROD
SA-57
1391 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE CENTER EXHAUST PIPE
3. REMOVE STRUT ROD
(a) Remove the bolt and disconnect the parking brake cable.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the 2 bolts and nuts.
Torque: 113 N´m (1,150 kgf´cm, 83 ft´lbf)
NOTICE:
Do not turn the nut.
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolts.
(c) Remove the strut rod.
4. REMOVE NO. 2 LOWER SUSPENSION ARM
(a) Remove the 3 nuts, suspension arm washer and washer.
Torque: 181 N´m (1,850 kgf´cm, 134 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nuts.
(b) Remove the No. 2 lower suspension arm.
HINT:
At the time of installation, face the paint mark to the rearward.
5. REMOVE STABILIZER BAR BRACKETS
(See page SA-63)
6. REMOVE NO. 1 LOWER SUSPENSION ARM
(a) Support the suspension member with a jack.
(b) Remove the 4 nuts, 2 bolts and 8 suspension member
stoppers.
Torque:
A: 51 N´m (520 kgf´cm, 38 ft´lbf)
B: 38 N´m (390 kgf´cm, 28 ft´lbf)
(c) Lower the suspension member.

SA0WA-02
R00749
F01924
F07383
SA-50
- SUSPENSION AND AXLEREAR SHOCK ABSORBER
1384 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR SEAT (See page BO-1 19)
2. REMOVE REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
3. DISCONNECT FLEXIBLE HOSE AND ABS SPEED
SENSOR WIRE HARNESS CLAMP
Remove the 2 bolts and disconnect the flexible hose and ABS
speed sensor wire harness clamp.
Torque:
Flexible hose: 29 N´m (300 kgf´cm, 22 ft´lbf)
ABS speed sensor wire harness:
5.4 N´m (55 kgf´cm, 48 in.´lbf)
4. DISCONNECT STABILIZER BAR LINK FROM SHOCK
ABSORBER (See page SA-63)
5. REMOVE SHOCK ABSORBER WITH COIL SPRING
(a) Loosen the 2 nuts on the lower side of the shock absorber.
Torque:
Reused nut: 196 N´m (2,000 kgf´cm, 145 ft´lbf)
New nut: 255 N´m (2,600 kgf´cm, 188 ft´lbf)
HINT:
At the time of installation, coat the nut's threads with engine oil.
(b) Support the rear axle carrier with a jack.
(c) Remove the cap.
(d) Loosen the nut in the center of the suspension support.
NOTICE:
Do not remove it.
Torque: 49 N´m (500 kgf´cm, 36 ft´lbf)
HINT:
If not disassembling the shock absorber, it is not necessary to
loosen the nut.
(e) Remove the 3 nuts of the suspension support.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(f) Lower the rear axle carrier and remove the 2 bolts on the
lower side of the shock absorber.
(g) Remove the shock absorber with the coil spring.

SA0VL-02
F06464
W03226
- SUSPENSION AND AXLEREAR STABILIZER BAR
SA-63
1397 Author
: Date
:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR WHEELS
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
2. REMOVE STABILIZER BAR LINKS
(a) Remove the 2 nuts and stabilizer bar link.
HINT:
If the ball joint turns together with the nut, use a hexagon (5 mm)
wrench to hold the stud.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(b) Employ the same manner described above to the other
side.
3. REMOVE BRACKETS AND BUSHINGS
(a) Remove the 2 bolts, bracket and bushing.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
HINT:
At the time of installation, install the bushing to the outside of
the bushing on the stabilizer bar.
(b) Employ the same manner described above to the other
side.
4. REMOVE STABILIZER BAR

SA0W8-02
Z00212
SST
Z00213
Nut
Washer
SA-48
- SUSPENSION AND AXLEREAR WHEEL HUB BOLT
1382 Author
: Date
:
2001 AVALON (RM808U)
REAR WHEEL HUB BOLT
REPLACEMENT
1. REMOVE REAR WHEEL
2. REMOVE BRAKE CALIPER AND DISC
(a) Remove the 2 bolts, brake caliper and disc.
(b) Support the brake caliper securely.
3. REMOVE HUB BOLT
Using SST and a hammer handle or an equivalent, remove the
hub bolt.
SST 09628-1001 1
4. INSTALL HUB BOLT
(a) Install a washer and nut to a new hub bolt as shown in the
illustration.
(b) Using a hammer handle or an equivalent to hold, install
the hub bolt by torquing the nut.
5. INSTALL DISC AND BRAKE CALIPER
Install the disc and brake caliper with the 2 bolts.
Torque: 47 N´m (475 kgf´cm, 34 ft´lbf)
6. INSTALL REAR WHEEL
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)