Page 400 of 1897
BO2OW-02
H15908
Rear SeatbackRear Seat Cushion
Upper Back Silencer
w/ Speaker:
High-mounted Stop Light
Luggage Compartment Door
Luggage Compartment
Weatherstrip
Luggage Compartment
Door Hinge Arm
w/o Speaker:
High-mounted
Stop Light
Rear Seat Belt Bezel
Rear Seat Belt Bezel
LH Roof Side
Inner Garnish
CRS Tether Anchor
Bracket Cover
Package Tray Trim
RH Roof Side Inner GarnishPin
Torsion Bar
Torsion Bar Clamp
RH Inner Luggage
Compartment Trim CoverFront LH Luggage Compartment
Trim Cover
LH Inner Luggage
Compartment Trim Cover
Front Luggage
Compartment
Trim Cover
Luggage Compartment Side Tray
Luggage Compartment
Floor Mat
Luggage Compartment
Side Cover
Luggage Compartment Door
Cover
No. 1 Luggage Compartment
Trim Hook
RH Rear Floor
Finish Side Plate
Rear Floor
Finish Plate
No. 1 Luggage
Compartment Trim Hook
Spare Wheel Cover Clamp
Luggage Compartment
Door Lock Cylinder
Rear Combination
Light
Spare Wheel CoverLH Rear Floor
Finish Side Platex4
x3
Backup Light
Rear Combination Light
Luggage Compartment Door Striker
Backup
Light
x3x4
Luggage Compartment Door LockLicense Plate Light
N´m (kgf´cm, ft´lbf) : Specified torque
7.8 (80, 69 in.´lbf)
7.8 (80, 69 in.´lbf)
Luggage
Compartment
Outside
Garnish
41 (420, 30)
41 (420, 30)
No. 1 Upper Back Panel Hole Cover
Room Partition
Reinforcement
Door Inside
Handle Bezel
5.4 (55, 48 in.´lbf)
Luggage Door Lock
Opener Assembly
5.4 (55, 48 in.´lbf)
BO-30
- BODYLUGGAGE COMPARTMENT DOOR AND HINGE
1815 Author: Date:
2001 AVALON (RM808U)
LUGGAGE COMPARTMENT DOOR AND HINGE
COMPONENTS
Page 405 of 1897
H12128
:7 Clips
H03125H12122H12806
w/o Speaker:
w/ Speaker:
2 Clips
H07599
H12124
2 Clips BO-32
- BODYLUGGAGE COMPARTMENT DOOR AND HINGE
1817 Author: Date:
2001 AVALON (RM808U)
17. REMOVE ROOF SIDE INNER GARNISH
(a) Using a screwdriver, remove the roof side inner garnish.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
18. REMOVE HIGH-MOUNTED STOP LIGHT
Remove the high-mounted stop light as shown in the illustra-
tion, then disconnect the connector.
19. REMOVE PACKAGE TRAY TRIM
(a) Using a screwdriver, remove the 3 rear seat belt bezel.
HINT:
Tape the screwdriver tip before use.
(b) Remove the package tray trim as shown in the illustration.
20. REMOVE UPPER BACK SILENCER
21. REMOVE TORSION BAR
(a) Disconnect the torsion bars from the torsion bar clamp,
then remove the torsion bar clamp.
Page 417 of 1897
BO2PH-01
H12701
Rear Seatback
Rear Seat CushionRH Rear Seat Inner with Center Belt
Roof Side Inner Garnish
Rear Door Opening Trim
Quarter WIndow Glass LH Rear Seat Inner with Center Belt
Non-reusable part
18 (185, 13)
41 (420, 30)
18 (185, 13)
BO-64
- BODYQUARTER WINDOW GLASS
1849 Author: Date:
2001 AVALON (RM808U)
QUARTER WINDOW GLASS
COMPONENTS
Page 430 of 1897
BO2OU-01
N12124
N12125
BO-22
- BODYREAR DOOR
1807 Author: Date:
2001 AVALON (RM808U)
ADJUSTMENT
1. ADJUST DOOR IN FORWARD/REARWARD AND VER-
TICAL DIRECTIONS
(a) Remove the front door scuff plate.
(b) Remove the center pillar lower garnish.
(c) Remove the front seat belt floor anchor.
(d) Remove the front seat belt retractor.
(See page BO-128)
(e) Remove the side airbag sensor assembly.
(See page RS-78)
(f) Loosen the body side hinge nuts to adjust.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(g) Reinstall the side airbag sensor assembly.
(See page RS-81)
Torque:
(h) Reinstall the front seat belt retractor.
(See page BO-137)
Torque:
Upper bolt: 7.5 N´m (76 kgf´cm, 66 in.´lbf)
Lower bolt: 41 N´m (420 kgf´cm, 30 ft´lbf)
(i) Reinstall the front seat belt floor anchor.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(j) Reinstall the center pillar lower garnish and front door
scuff plate.
2. ADJUST DOOR IN LEFT/RIGHT AND VERTICAL
DIRECTIONS
Loosen the door side hinge bolts to adjust.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
Page 432 of 1897
BO2OS-01
H12120
Door Lock Striker
Rear Guide Bracket
Garnish
23 (230, 17)
Rear Door
Window Guide
Rear Door Weatherstrip
Rear Door Glass Run
Rear Door Glass
Outside Handle
5.4 (55, 48 in.´lbf)
5.4 (55, 48 in.´lbf)
Door Lock
Door Lock ProtectorRear Door Outside
Lower Moulding
Door Speaker Board
25 (260, 19)
25 (260, 19)25 (260, 19)
7.8 (80, 69 in.´lbf)
Door Check
25 (260, 19)
Door Hinge
Inside Handle
Inside Handle Bezel
Service Hole Cover
Rear Door Belt Moulding
Cover
Upper Armrest Base Panel
Power Window
Switch
Rear Door ArmrestRear Door
Inner Weatherstrip
Door Trimx13
x7
Window Regulator
Guide Assembly
Window Regulator Motor
5.4 (55, 48 in.´lbf)
Rear Door Trim Pocket
: Specified torqueN´m (kgf´cm, ft´lbf)
Precoated Part
5.4 (55, 48 in.´lbf)
4.9 (50, 43 in.´lbf)
Guide Piece Plate
BO-16
- BODYREAR DOOR
1801 Author: Date:
2001 AVALON (RM808U)
REAR DOOR
COMPONENTS
Page 434 of 1897
H12163
x13
x7
H06127
H12115
H12116
Protective Tape BO-18
- BODYREAR DOOR
1803 Author: Date:
2001 AVALON (RM808U)
(c) Using a screwdriver, remove the rear door inner weather-
strip.
(d) Remove the 13 screws and rear door armrest.
(e) Remove the 7 screws and rear door trim pocket.
5. REMOVE INSIDE HANDLE
(a) Remove the screw.
(b) Slide the inside handle backward to remove it.
(c) Disconnect the 2 cables from the inside handle as shown
in the illustration.
6. REMOVE DOOR SPEAKER BOARD
7. REMOVE SERVICE HOLE COVER
(a) Disconnect the 2 control cables from the link clamp.
(b) Using a clip remover, remove the grommets and link
clamp.
(c) Remove the service hole cover.
NOTICE:
Do not tear the cover.
HINT:
At the time of reassembly, please refer to the following item.
Bring out the 2 control cables and wire harness through the ser-
vice hole cover.
8. REMOVE REAR DOOR WEATHERSTRIP
(a) Remove the screw from the door check.
(b) Using a clip remover, remove the rear door weatherstrip.
(c) Reinstall the screw to the door check.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
9. REMOVE REAR DOOR BELT MOULDING
(a) Apply protective tape to the outer surface as shown in the
illustration, to keep the surface from being scratched.
(b) Using a moulding remover, remove the rear door belt
moulding.
Page 439 of 1897
BO2QD-01
H12219
Center Armrest
Seat Cushion Pad
with Frame Seat Cushion Cover
Center Armrest Bracket
Center Armrest Hinge
Hog Ring
Shoulder Belt Guide
Headrest
Headrest Support
Headrest Support
Seatback Pad with Frame
Hog Ring
N´m (kgf´cm, ft´lbf): Specified torque
Non-reusable partSeatback Cover
5.9 (60, 52 in.´lbf)
18 (185, 13)
41 (420, 30)
18 (185, 13)
- BODYREAR SEAT
BO-1 19
1904 Author: Date:
2001 AVALON (RM808U)
REAR SEAT
COMPONENTS
Page 440 of 1897
BO2QF-01
H03147
- BODYREAR SEAT
BO-121
1906 Author: Date:
2001 AVALON (RM808U)
DISASSEMBLY
1. REMOVE HEADRESTS
2. REMOVE CENTER ARMREST
Remove the 2 nuts and center armrest.
Torque: 5.9 N´m (60 kgf´cm, 52 in.´lbf)
3. REMOVE SHOULDER BELT GUIDES
Remove the 4 screws and 2 shoulder belt guides.
4. REMOVE HEADREST SUPPORTS
5. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover from the seatback
pad with frame.
6. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
