Page 224 of 801

YH4
GRAND
VITARA
3D-22 FRONT SUSPENSION
1. Hydraulic press
2. Front bushing
A: Bushing flange
contacts housing edge
1. Hydraulic press
2. Rear bushing
A: Bushing flange
contacts housing edge
INSTALLATION
1) Front bushing
Press-fit front bushing until its flange contacts housing edge of
control arm, use special tools as shown.
Special Tool
(C): 09951-16060
(F): 09913-85210
NOTE:
When press-fitting bushing, compounding oil or soap water
applied to inside of control arm housing will facilitate work.
2) Rear bushing
Press-fit rear bushing until its flange contacts housing edge of
control arm, use special tools as shown.
Special Tool
(E): 09925-58210
(F): 09913-85210
NOTE:
When press-fitting bushing, compounding oil or soap water
applied to inside of control arm housing will facilitate work.
3) Install control arm to chassis.
Tighten suspension arm nut to specified torque after lowering
hoist and vehicle in non-loaded condition.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
(b): 127 N.m (12.7 kg-m, 92.0 lb-ft)
4) As installation procedure hereafter is the same as that for coil
spring. Refer to ªCOIL SPRINGº in this section.
NOTE:
For any tightening torque other than those specified in text,
refer to ªTORQUE SPECIFICATION TABLEº at the end of
this section.
Page 225 of 801
YH4
GRAND
VITARA
FRONT SUSPENSION 3D-23
TIGHTENING TORQUE SPECIFICATIONS
Page 235 of 801
YH4
GRAND
VITARA
1. Axle housing
2. Floor jack
1. Lower rod
2. Rear mount nut1. Lower rod
2. Front mount bolt
1. Lower rod
2. Front bolt
3. Rear bolt
4. Vehicle body
5. Axle housing
6. Body center
7. Body out side
[A]: Body side
[B]: Axle side
3E-8 REAR SUSPENSION
LOWER ROD
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) Support rear axle housing by using floor jack.
3) Remove lower rod front mount bolt.
4) Remove lower rod rear mount bolt.
INSTALLATION
1) Install lower rod to chassis frame and axle housing, referring to
figure for proper installing direction of bolts.
Nuts should not be tightened.
2) Remove floor jack from rear axle housing.
3) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque for wheel nuts
100 N
.m (10.0 kg-m, 72.5 lb-ft)
4) Lower hoist and with vehicle in non loaded condition, tighten
front bolt and rear nut of lower rod to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65.0 lb-ft)
Page 236 of 801
YH4
GRAND
VITARA
1. Clamp
2. Upper rod
1. Upper rod front bolt
2. Nut
3. Upper rod
4. Wheel speed sensor
harness bracket
(Toward outside of body)1. Upper rod
2. Bolt
5. Upper rod rear bolt
6. Washer
7. Body center
8. Front side
REAR SUSPENSION 3E-9
UPPER ROD
REMOVAL
1) Hoist vehicle and remove rear wheel.
2) If equipped with ABS, disconnect wheel speed sensor harness
clamp from left upper rod.
3) Remove upper rod.
INSTALLATION
1) Install upper rod to chassis frame and axle housing, referring to
figure for installing direction of bolts.
Nuts should not be tightened.
2) See figure for distinction of installing direction of left side upper
rod for vehicle equipped with ABS.
3) Connect wheel speed sensor harness clamp to upper rod (if
equipped with ABS).
4) Lower hoist and with vehicle in non-loaded condition, tighten
front bolt and rear nut of upper rod to specified torque.
Tightening Torque
(a): 90 N
.m (9.0 kg-m, 65 lb-ft)
Page 280 of 801

YH4
GRAND
VITARA
5-4 BRAKES
DIAGNOSIS TABLE
ConditionPossible CauseCorrection
Not enough brak-
ing forceBrake oil leakage from brake lines.
Brake disc or pads stained with oil.
Overheated brakes.
Poor contact of shoes on brake drum.
Brake shoes linings stained with oil or wet
with water.
Badly worn brake shoe linings.
Defective wheel cylinders.
Malfunctioning caliper assembly.
Air in system.
Maladjusted sensor spring length of LSPV.
Broken sensor spring of LSPV.
Defective collar of LSPV.
Malfunctioning ABS (Antilock brake system),
if equipped.Locate leaking point and repair.
Clean or replace.
Determine cause and repair.
Repair for proper contact.
Replace.
Replace.
Repair or replace.
Repair or replace.
Bleed system.
Check or adjust.
Replace.
Replace.
Check system and replace as
necessary.
Brake pull
(Brakes not work-
ing in unison)Pad or shoe linings are wet with water or
stained with oil in some brakes.
Drum-to-shoe clearance out of adjustment in
some brakes.
(Malfunctioning auto adjusting mechanism)
Drum is out of round in some brakes.
Wheel tires are inflated unequally.
Malfunctioning wheel cylinders.
Disturbed front end alignment.
Unmatched tires on same axle.
Restricted brake pipes or hoses.
Malfunctioning caliper assembly.
Loose suspension parts.
Loose calipers.Replace.
Check for inoperative auto adjusting
mechanism.
Replace.
Inflate equally.
Repair or replace.
Adjust as prescribed.
Tires with approximately the same
amount of tread should be used on the
same axle.
Check for soft hoses and damaged
lines.
Replace with new hoses and new
brake pipes.
Check for stuck or sluggish pistons
and proper lubrication of caliper slide
bush.
Caliper should slide.
Check all suspension mountings.
Check and torque bolts to specifica-
tions.
Noise (High pitched
squeak without
brake applied)Front lining worn out.Replace linings.
Rear brake locked
prematurelyMaladjusted sensor spring length of LSPV.
Malfunction LSPV assembly.Check or adjust.
Replace assembly.
Brake locked
(For vehicles
equipped with
ABS)Malfunctioning ABS, if equipped.Check system and replace as
necessary.
Page:
< prev 1-8 9-16 17-24