2001 SUZUKI GRAND VITARA abs

YH4
GRAND
VITARA
1. Master cylinder
1. Attaching bolt
2. Attaching nut
3. Clevis pin
ªAº
7C1-6 CLUTCH
INSTALLATION
1) To bleed air from master cylinder itself, tilt it as shown in figure
and add fluid into it.
NOTE:
After bleeding air from master cylinder, plug pipe hole in it
to prevent fluid from spilling out of it till pipe is connected.
2) Install master cylinder assembly and new gasket to body, attach-
ing bolt, nuts and push rod clevis pin.
NOTE:
Do not reuse gasket.
3) Torque attaching bolt and nut to specification.
4) Connect fluid pipe and torque flare nut to specification.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
5) Apply grease to clevis pin and install it.
ªAº: Grease 99000-25010
6) Fill reservoir with specified brake fluid and check fluid leakage.
7) After installation, bleed air from system and check clutch pedal
free travel. Refer to BRAKE section for air bleeding procedure.
FLUID INSPECTION
Fluid level should be always between MIN and MAX lines on reser-
voir. If fluid decreases quickly, check for leakage, repair leaky point,
if any, and add fluid up to MAX level.
NOTE:

Brake fluid damages painted surface badly. Should it get on
painted surface, remove it immediately and clean surface
thoroughly.

Do not use shock absorber fluid or any other fluid which con-
tains mineral oil. Do not use container which has been used
for mineral oil or which is wet from water. Mineral oil will
cause swelling and distortion of rubber parts in hydraulic
clutch system and water will mix with brake fluid, lowering
fluid boiling point. Keep all fluid containers capped to pre-
vent contamination.

Make sure not to use fluid whose container cap was first
opened more than a year ago.

YH4
GRAND
VITARA
1. Tachometer
2. Speedometer
3. Fuel level meter
4. Water temperature meter
5. Turn signal pilot light (LH)
6. 4WD indicator (if equipped)
7. ABS warning light (if equipped)
8. Immobilizer warning light (if equipped)
9. CHECK ENGINE light
10. Turn signal pilot light (RH)11. AIR BAG warning light (if equipped)
12. O / D OFF light (A / T vehicle only)
13. Fasten seat belt light (if equipped)
14. High beam light
15. Oil pressure warning light
16. Charge warning light
17. Brake and parking brake warning light
18. POWER indicator light (A / T vehicle only)
19. Shift position indicator (A / T vehicle, if equipped)or
CHECK
ENGINEor
ABS
8C-2 INSTRUMENTATION / DRIVER INFORMATION
GENERAL DESCRIPTION
CAUTIONS IN SERVICING
Refer to Section 8.
SYMBOLS AND MARKS
Refer to Section 8.
WIRING COLOR SYMBOLS
Refer to Section 8.
ABBREVIATIONS
Refer to Section 8.
JOINT CONNECTOR
Refer to Section 8.
FUSE BOX AND RELAY
Refer to Section 8.
POWER SUPPLY DIAGRAM
Refer to Section 8.
COMBINATION METER

YH4
GRAND
VITARA
1. To door switch (driver side) B / Bl
2. To transmission range switch G / Bl
(A / T vehicle only, if equipped) L
3. To transmission range switch G / O
(A / T vehicle only, if equipped) 2
4. To transmission range switch Y / G
(A / T vehicle only, if equipped) D
5. To transmission range switch O / Bl
(A / T vehicle only, if equipped) N
6. To transmission range switch O / G
(A / T vehicle only, if equipped) P
7. To transmission range switch R
(A / T vehicle only, if equipped) R
8. To ground B
9. To PCM (A / T vehicle only) W / B
10. To ECT sensor Y / W
11. To fuel level gauge Bl / W
12. To ground B / Y
13. To combination switch G / Y
NOTE:
Terminal arrangement of coupler viewed from harness side.
Coupler A Coupler B Coupler C
Coupler A Coupler B Coupler C
1. Blank ÐÐ
2. Blank ÐÐ
3. To ignition switch B / W
4. Blank ÐÐ
5. To ABS control module Bl / O
(if equipped)
6. To PCM (A / T vehicle only) Gr / Bl
7. To ABS control module Br
(if equipped)
8. To VSS Bl / Y
9. To combination switch G / R
10. To SDM (if equipped) Y / G or Bl
11. To main fuse W / Bl
12. To fuse box W
13. To combination switch R
14. To ECM (PCM for A / T vehicle) V
(if equipped)
15. To ECM (PCM for A / T vehicle) V / Y
16. To ECM (PCM for A / T vehicle) O / B
(if equipped)1. To ground B
2. To ECM (PCM for A / T vehicle) Br
3. To ignition switch (if equipped) V / R
4. To brake fluid level switch R / B
5. To parking brake switch V
6. To seat belt switch (if equipped) Gr / R
7. To generator W / R
8. To oil pressure switch Y / B
9. To combination switch R / Y
10. To ignition switch (if equipped) Bl / R or CHECK
or ENGINE
or ABSif equipped
if equippedif equipped
INSTRUMENTATION / DRIVER INFORMATION 8C-3

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-3
1
A1 A2 A3 A4
A5 A6 A9 A10A7 A8
1. Coil antenna
2. Immobilizer Control Module
3. ECM/PCM
4. Immobilizer diagnostic coupler
4-1. Diagnostic output terminal
4-2. Ground terminal
5. Malfunction indicator lamp
6. Main relay
7. Ignition switch
8. Fuse
9. Main fuse
-10. To #9-pin in Data link connector
-11. To #7-pin in Data link connector
-12. To ABS control module
-13. Immobilizer indicator lamp
(Vehicle not equipped with monitor coupler)
-14. Monitor coupler (Vehicle not equipped
with immobilizer indicator lamp)) Terminal arrangement of Immobilizer
Control Module coupler (Viewed from
harness side)
B/R
BI
BI/B
B/W
V/Y
BI/B
B/W
B
V/W
V/W
BI
R
SbI
B
V/G
V
B
R/Y WIRE
SYMBOLWIRE
COLORabcdefghijklmn
1. Ignition key with built-in
transponder
1
1. Coil antenna
opqr
IGNITION KEY
The ignition key for the immobilizer control system has a built-in
transponder. Each transponder in the key has an each transmitting
code (Transponder code). The code will transmitted from the key
via the coil antenna to Immobilizer Control Module when the ignition
switch is turned ON.
COIL ANTENNA
The coil antenna is installed to the steering lock assembly. As it is
energized by Immobilizer Control Module, it transmits the trans-
ponder code of the ignition key to Immobilizer Control Module.

YH4
GRAND
VITARA
BODY SERVICE 9-25
a. Front bumper
b. 1st mounting
c. Suspension frame
d. Front strut
e. Suspension arm
f. 2nd mounting
g. ù20 zig hole
h. Zig hole
i. 3rd mounting
j. Lower rod
k. Upper rod
l. Lateral rod
m. Rear shock absorber
n. 4th mounting
o. Fuel tank
p. Fuel tank
q. Lower roda ± g : 1315 mm (51.77 in.)
a ± g' : 1534 mm (60.39 in.)
b ± g : 1243 mm (48.94 in.)
b ± g' : 1518 mm (59.76 in.)
c ± g : 1377 mm (54.21 in.)
c ± g' : 1105 mm (43.50 in.)
d ± g' : 1319 mm (51.93 in.)
d ± f : 874 mm (34.41 in.)
e ± g : 525 mm (20.67 in.)
e ± g' : 857 mm (33.74 in.)
f ± g' : 927 mm (36.50 in.)
h ± i : 178 mm (7.01 in.)
h ± j : 133 mm (5.24 in.)
h ± k : 325 mm (12.80 in.)
h ± l : 674 mm (26.54 in.)h ± m : 803 mm (31.61 in.)
h ± n : 1161 mm (45.71 in.)
h ± o : 1184 mm (46.61 in.)
h ± p : 1190 mm (46.85 in.)
i ± q : 999 mm (39.33 in.)
j ± q : 997 mm (39.25 in.)
k ± q : 824 mm (32.44 in.)
l ± q : 1130 mm (44.49 in.)
m ± q : 1258 mm (49.53 in.)
n ± q : 1483 mm (58.39 in.)
o ± q : 1349 mm (53.11 in.)
p ± q : 1334 mm (52.52 in.)
For 4 door model
g' ± q : 1275 mm (50.20 in.)
g ± q : 1534 mm (60.39 in.)
For 2 door model
g' ± q : 995 mm (39.17 in.)
g ± q : 1310 mm (51.57 in.)
UNDER BODY DIMENSIONS

YH4
GRAND
VITARA
9-36 BODY SERVICE
Sealer is applied to the specific joints of a vehicle dur-
ing production. The sealer is intended to prevent dust
from entering the vehicle and serves also as an anti-
corrosion barrier. The sealer is applied to the door and
hood hem areas and between panels. Correct and re-
seal the originally sealed joints if damaged. Reseal
the attaching joints of a new replacement panel and
reseal the hem area of a replacement door or hood.
Use a quality sealer to seal the flanged joints, overlap
joints and seams. The sealer must have flexible char-
acteristics and paintability after it's applied to repair
areas.
For the sealer to fill open joints, use caulking material.
Select a sealer in conformance with the place and
purpose of a specific use. Observe the manufactur-
er's label-stand instructions when using the sealer.
In many cases, repaired places require color painting.
When this is required, follow the ordinary techniques
specified for the finish preparation, color painting and
undercoating build-up.
Rust proof wax, a penetrative compound, is applied
to the metal-to-metal surfaces (door and side sill in-
sides) where it is difficult to use ordinary undercoating
material for coating. Therefore, when selecting the
rust proof wax, it may be the penetrative type.
During the undercoating (vinyl coating) application,
care should be taken that sealer is not applied to the
engine-related parts and shock absorber mounting or
rotating parts. Following the under coating, make
sure that body drain holes are kept open.
he sequence of the application steps of the anti-corro-
sion materials are as follows:
1) Clean and prepare the metal surface.
2) Apply primer.
3) Apply sealer (all joints sealed originally).
4) Apply color in areas where color is required such
as hem flanges, exposed joints and under body
components.
5) Apply anticorrosion compound (penetrative wax).
6) Apply undercoating (rust proof material).
PAINT AND COATINGS
ANTI-CORROSION TREATMENT
WARNING:
Standard shop practices, particularly eye
protection, should be followed during the per-
formance of the below-itemized operations to
avoid personal injury.
As rust proof treatment, steel sheets are given corro-
sion resistance on the interior and / or exterior.
These corrosion resistance steel sheet materials are
called one of two-side galvanized steel sheets.
It is for the sake of rust protection that these materials
are selected and given a variety of treatments as de-
scribed blow.
1) Steel sheets are treated with cathodic electroprim-
er which is excellent in corrosion resistance.
2) Rust proof wax coatings are applied to door and
side sill insides where moisture is liable to stay.
3) Vinyl coating is applied to body underside and
wheel housing inside.
4) Sealer is applied to door hem, engine compart-
ment steel sheet-to-steel sheet joint, and the like
portions to prevent water penetration and resulting
in rust occurrence.
In panel replacement or collision damage repair, leav-
ing the relevant area untreated as it is in any operation
which does disturb the above-mentioned rust proof
treatment will cause corrosion to that area. Therefore,
it is the essential function of any repair operation to
correctly recoat the related surfaces of the relevant
area.
All the metal panels are coated with metal condition-
ers and primer coating during vehicle production. Fol-
lowing the repair and / or replacement parts installa-
tion, every accessible bare metal surface should be
cleaned and coated with rust proof primer. Perform
this operation prior to the application of sealer and
rust proof wax coating.

YH4
GRAND
VITARA
When the welding or heating operation causes the
original galvanization or other anticorrosive materials
to be burnt, the interior and under-body panel sur-
faces must be cleaned.
Removal of residues of the burning should be carried
out carefully when the relevant place has boxtype
construction or has shape which limits the access to
the interior surfaces. In general, the following method
can be used satisfactorily for the removal of those res-
idues.Scrape the accessible places. If a standard putty knife
or scraper does not fit to the elevant place, consider
to use a more flexible scraper to a place narrowly en-
closed by sheet metals.
A jet of compressed air can remove most residues,
and is effective to limited areas.
However, this type of operation absolutely requires
eye protection.
BODY SERVICE 9-37
The metal service replacement parts (or assemblies)
are coated with electro-deposition primer.
For the proper adhesion of a paint, the following finish
process (refinish steps) becomes necessary.
1) Use wax or grease-removing solvent to clean the
part.
2) Use a wet or dry sand-paper (No. 400) to polish the
panel lightly. Do not polish it forcibly to produce any
scratch. Clean the part again.
3) If factory-applied primer coating is cut through to
the bare metal, apply metal conditioner to the bare
metal exposed to open air. As for method of use of
the metal conditioner, follow directions on the con-
tainer.
4) Apply primer-surfacer to the part completely dry
before starting sand-paper polishing. As for drying
time, follow directions advised on the primer-sur-
facer container.
5) Use a wet or dry sand-paper (No. 400) and water
to polish the panel lightly.
6) Wash the part again.
7) Apply color, coating to the part.
8) Different paints demand different drying methods.
Hence, follow directions advised on the pertinent
paint container.9) When lacquer coating (quick-drying paint coat-
ing) is applied, dry coated surface and polish it
with compound.
In the case of the melamine or acrylic coating,
compound polishing can be omitted after drying.
10) If the case of lacquer coating, wax should not be
applied to coated surface until the surface has
dried completely (for approx. two months).
Before replacing exterior parts or assemblies, check
paint conditions of all the covered or hidden interior
surfaces. If any rust scale is found at these places,
proceed as follows:
1) Use a proper wire brush, adhesive or liquid rust re-
moving agent to remove rust. As for the method of
use, follow directions advised for respecitve mate-
rials.
2) If necessary, wash parts with detergent, rinse, and
dry them.
3) Before installing exterior body parts, apply anticor-
rosive compound to all cleaner surfaces of exterior
body parts. Also, apply anticorrosive compound to
inner surfaces of exterior body parts to be
installed.
METAL REPLACEMENT PARTS FINISHING

YH4
GRAND
VITARA
9-58 BODY SERVICE
PLASTIC PARTS FINISHING
Paintable plastic parts are ABS plastic parts.
Painting
Rigid or hard ABS plastic needs no primer coating.
General acrylic lacquers can be painted properly over hard ABS
plastic in terms of adherence.
1) Use cleaning solvent for paint finish to wash each part.
2) Apply conventional acrylic color lacquer to part surface.
3) Follow lacquer directions for required drying time. (Proper dry-
ing temperature range is 60 to 70
C).
Reference
Plastic parts employ not only ABS (Acrylonitrile Butadiene Styrene)
plastic but also polypropylene, vinyl, or the like plastic. Burning test
method to identify ABS plastic is described below.
1) Use a sharp blade to cut off a plastic sliver from the part at its
hidden backside.
2) Hold sliver with pincers and set it on fire.
3) Carefully observe condition of the burning plastic.
4) ABS plastic must raise readily distinguishable back smoke while
burning with its residue suspended in air temporarily.
5) Polypropylene must raise no readily distinguishable smoke
while burning.