2001 SUZUKI GRAND VITARA AC relay

6-1-62 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
Fig. for STEP 34 HO2S heater control circuit check :
1) With ignition switch OFF, install HO2S
heater relay.
2) With ignition switch ON leaving engine OFF,
check voltage between C51-2-4 and
ground.
Is the voltage 10 – 14 V?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S heater relay
or “BLK” wire open, “BLU”
wire open or shorted to
ground circuit
or
“GRY” wire open or
shorted to ground circuit.
If OK, substitute a known-
good ECM (PCM) and
recheck. Step Action Yes No
a. HO2S heater relay

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-63
DTC P0136 HO2S-2 (Bank 1) Circuit Malfunction
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1. HO2S heater relay
2. ECM (PCM)
3. HO2S-2 (Bank-1)
DTC DETECTING CONDITION TROUBLE AREA
DTC will set when any one of following conditions is detected (2 driving
cycle detection logic).
• 4.5 V or more HO2S circuit voltage is detected when 5 V power is con-
nected to HO2S circuit in ECM (PCM).
• While running with A/F feed back, average output voltage during speci-
fied time is too high or too low.
or
• While running with A/F feed back, max output voltage during specified
time is lower than specified value or min. output voltage during speci-
fied time is higher than specified value.• HO2S-2 or its circuit
• Fuel system
•ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.

6-1-66 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
TROUBLESHOOTING
Fig. for STEP 2, 3Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 HO2S-2 heater check :
1) Disconnect HO2S-2 coupler with ignition
switch OFF.
2) Check resistance between “3” and “4” termi-
nal of HO2S-2 connector.
HO2S -2 heater resistance :
11.7 – 14.3
Ω
ΩΩ Ω (at 20°C (68°F))
Is it within above specificationGo to Step 3. Replace HO2S-2.
3 HO2S heater power supply check :
1) With ignition switch ON leaving engine OFF,
check voltage between E139-3 and ground,
E139-1 and ground. (See Fig.)
Is each voltage 10 – 14 V?Go to Step 4. Fuse “HO2S” and/or “IG
METER” blown.
If OK, faulty “BLK/WHT”
wire or “BLU/WHT” wire.
4 HO2S heater control circuit check :
1) With ignition switch OFF, install HO2S
heater relay.
2) With ignition switch ON leaving engine OFF,
check voltage between C51-2-16 and
ground.
Is the voltage 10 – 14 V?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S heater relay
or “BLK” wire open, “BLU”
wire open or shorted to
ground circuit, “WHT/
BLK” wire open or shorted
to ground circuit.
If OK, substitute a known-
good ECM (PCM) and
recheck.
a. HO2S heater relay

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-67
DTC P0150 (DTC No.26) HO2S-1 (Bank 2) Circuit Malfunction or No Activity
Detected
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
1. HO2S heater relay
2. ECM (PCM)
3. HO2S-1 (Bank-2)
NOTE:
For vehicle with monitor connector, DTC will set when following only (*) mark condition is detected.
DTC DETECTING CONDITION TROUBLE AREA
Any one of the following conditions are detected in idle state while running
under driving conditions described for “DTC CONFIRMATION PROCEDURE”.
• 4.5 V or more HO2S circuit voltage is detected, when 5 V power is con-
nected to HO2S circuit in ECM (PCM), or
• Max. output voltage of HO2S is 0.6 V or lower on average and its minimum
voltage on average is 0.3 V or lower.
• Min. output voltage of HO2S is over 3.0 V or
• Max. output voltage of HO2S is 0.74 V or higher on average and its min.
voltage on average is 0.33 V or higher.
• Output voltage of HO2S-1 does not exceed 0.45 V for specified time.
(2 driving cycle detection logic)HO2S-1 or its circuit.
Fuel system
ECM (PCM)

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-71
Fig. for STEP 2, 34 HO2S heater control circuit check :
1) With ignition switch OFF, install HO2S
heater relay.
2) With ignition switch ON leaving engine OFF,
check voltage between C51-2-4 and
ground.
Is the voltage 10 – 14 V?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S heater relay
or “BLK” wire open, “BLU”
wire open or shorted to
ground circuit, “BLK/RED”
wire open or shorted to
ground circuit.
If OK, substitute a known-
good ECM (PCM) and
recheck. Step Action Yes No
a. HO2S heater relay

6-1-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0156 HO2S-2 (Bank 2) Circuit Malfunction
WIRING DIAGRAM
DTC DETECTING CONDITION AND TROUBLE AREA
DTC CONFIRMATION PROCEDURE
1. HO2S heater relay
2. ECM (PCM)
3. HO2S-2 (Bank-2)
DTC DETECTING CONDITION TROUBLE AREA
DTC will set when any one of following conditions is detected (2 driving
cycle detection logic).
• 4.5 V or more HO2S circuit voltage is detected when 5 V power is con-
nected to HO2S circuit in ECM (PCM).
• While running with A/F feed back, average output voltage during speci-
fied time is too high or too low.
or
• While running with A/F feed back, max output voltage during specified
time is lower than specified value or min. output voltage during speci-
fied time is higher than specified value.• HO2S-2 or its circuit
• Fuel system
• ECM (PCM)
WARNING:
When performing a road test, select a place where there is no traffic or possibility of a traffic acci-
dent and be very careful during testing to avoid occurrence of an accident.
Road test should be carried out with 2 persons, a driver and a tester, on a level road.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-75
TROUBLESHOOTING
Fig. for STEP 2, 3Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 HO2S-2 heater check :
1) Disconnect HO2S-2 coupler with ignition
switch OFF.
2) Check resistance between “3” and “4” termi-
nal of HO2S-2 connector.
HO2S -2 heater resistance :
11.7 – 14.3
Ω
ΩΩ Ω (at 20°C (68°F))
Is it within above specificationGo to Step 3. Replace HO2S-2.
3 HO2S heater power supply check :
1) With ignition switch ON leaving engine OFF,
check voltage between E139-3 and ground,
E139-1 and ground. (See Fig.)
Is each voltage 10 – 14 V?Go to Step 4. Fuse “HO2S” and/or “IG
METER” blown.
If OK, faulty “BLK/WHT”
wire or “BLU/WHT” wire.
4 HO2S heater control circuit check :
1) With ignition switch OFF, install HO2S
heater relay.
2) With ignition switch ON leaving engine OFF,
check voltage between C51-2-17 and
ground.
Is the voltage 10 – 14 V?Substitute a known-good
ECM (PCM) and recheck.Faulty HO2S heater relay
or “BLK” wire open, “BLU”
wire open or shorted to
ground circuit, “PNK/
WHT” wire open or
shorted to ground circuit.
If OK, substitute a known-
good ECM (PCM) and
recheck.
a. HO2S heater relay

6-1-86 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
DTC P0340 (DTC No.42) Camshaft Position Sensor Circuit Malfunction
WIRING DIAGRAM
SYSTEM DESCRIPTION
CMP sensor detects REF signal and POS signal.
• REF signal : 4 pulses/1 revolution of camshaft. There are 2 different kinds of wavelength. Based on REF sig-
nal, ECM (PCM) judges which cylinder is at TDC.
• POS signal : 6 pulse/1 revolution of camshaft. Each of POS signals has equivalent wavelength. Based on
POS signal, ECM (PCM) judges the wavelength of REF signals, engine speed and piston position.
REFERENCE
Connect oscilloscope between terminals C51-1-13 (POS) or C51-1-12 (REF) and C51-3-26 (ground) of ECM
(PCM) connector connected to ECM (PCM) and check CMP sensor signal.
1. CMP sensor
2. To main relay
3. ECM (PCM)