2001 SUZUKI GRAND VITARA engine oil

6-1-40 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
C51-1-10A/T input speed sensor (–)
(A/T vehicle)About 2.5 V Ignition switch ON
C51-1-11A/T input speed sensor (+)
(A/T vehicle)About 2.5 V Ignition switch ON
C51-1-12 Camshaft position sensor 1Deflects between
0 – 1 V and 4 – 6 VIgnition switch ON, crankshaft
turned slowly
C51-1-13 Camshaft position sensor 2Deflects between
0 – 1 V and 4 – 6 VIgnition switch ON, crankshaft
turned slowly
C51-1-14 Vehicle speed sensorDeflects between
0 – 1 V and over 4VIgnition switch ON, Rear right tire
turned slowly with rear left tire
locked
C51-1-15 EVAP canister purge valve 10 – 14 V Ignition switch ON
C51-1-16 IAC valve (stepper motor coil 4) – –
C51-1-17 IAC valve (stepper motor coil 3) – –
C51-1-18Transmission range switch “D”
(A/T vehicle)10 – 14 VIgnition switch ON, selector lever :
“D” range
0 – 1 VIgnition switch ON, selector lever :
Other than “D” range
C51-1-19Transmission range switch “N”
(A/T vehicle)10 – 14 VIgnition switch ON, selector lever :
“N” range
0 – 1 VIgnition switch ON, selector lever :
Other than “N” range
C51-1-20Shield wire ground for A/T output
speed sensor (A/T vehicle)––
C51-1-21Shield wire ground for A/T input
speed sensor (A/T vehicle)––
C51-1-22A/T output speed sensor (–)
(A/T vehicle)About 2.5 V Ignition switch ON
C51-1-23A/T output speed sensor (+)
(A/T vehicle)About 2.5 V Ignition switch ON
C51-1-24 Engine start signal10 – 14 V While engine cranking
0 – 1 V Other than above
C51-1-25 Power steering pressure switch10 – 14 V Ignition switch ON
0 – 1 VWith engine running at idle speed,
turning steering wheel to the right or
left as far as it stops
C51-1-26 4WD low switch0 – 1 VIgnition switch ON, Transfer lever :
4WD low range
10 – 14 VIgnition switch ON, Transfer lever :
4H or 2H range
C51-1-27Transmission range switch “L”
(A/T vehicle)10 – 14 VIgnition switch ON, selector lever :
“L” range
0 – 1 VIgnition switch ON, selector lever :
Other than “L” range
C51-1-28Transmission range switch “2”
(A/T vehicle)10 – 14 VIgnition switch ON, selector lever :
“2” range
0 – 1 VIgnition switch ON, selector lever :
Other than “2” range TERMINAL CIRCUIT NORMAL VOLTAGE CONDITION

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-41
C51-2-1 Fuel injector No.2
10 – 14 V Ignition switch ON
C51-2-2 Fuel injector No.1
C51-2-3 – – –
C51-2-4Heater of HO2S-1 (bank 1)
(if equipped)10 – 14 V Ignition switch ON
0 – 2 VAt specified idle speed after engine
warmed up
C51-2-5Heater of HO2S-1 (bank 2)
(if equipped)10 – 14 V Ignition switch ON
0 – 2 VAt specified idle speed after engine
warmed up
C51-2-6 – – –
C51-2-7 Ground – –
C51-2-8 Fuel injector No.4
10 – 14 V Ignition switch ON
C51-2-9 Fuel injector No.3
C51-2-10 – – –
C51-2-11 – – –
C51-2-12EGR valve (stepper motor coil 4)
(if equipped)0 – 1 V
Ignition switch ON C51-2-13EGR valve (stepper motor coil 3)
(if equipped)10 – 14 V
C51-2-14EGR valve (stepper motor coil 2)
(if equipped)10 – 14 V
C51-2-15EGR valve (stepper motor coil 1)
(if equipped)0 – 1 V
C51-2-16Heater of HO2S-2 (bank 1)
(if equipped)10 – 14 V Ignition switch ON
0 – 1 VAt specified idle speed after engine
warmed up
C51-2-17Heater of HO2S-2 (bank 2)
(if equipped)10 – 14 V Ignition switch ON
0 – 1 VAt specified idle speed after engine
warmed up
C51-2-18 – – –
C51-2-19Crankshaft position sensor (+)
(if equipped)––
C51-2-20Crankshaft position sensor (–)
(if equipped)––
C51-2-21 Fuel injector No.6
10 – 14 V Ignition switch ON
C51-2-22 Fuel injector No.5
C51-2-23 Ignition coil assembly for No.6 – –
C51-2-24 Ignition coil assembly for No.5 – –
C51-2-25 Ignition coil assembly for No.4 – –
C51-2-26 Ignition coil assembly for No.3 – –
C51-2-27 Ignition coil assembly for No.2 – –
C51-2-28 Ignition coil assembly for No.1 – –
C51-2-29 – – –
C51-2-30Ground for CKP sensor shield wire
(if equipped)–– TERMINAL CIRCUIT NORMAL VOLTAGE CONDITION

6-1-42 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
RESISTANCE CHECK
1) Disconnect couplers (1) from ECM/PCM with ignition switch
OFF.
2) Check resistance between each pair of terminals of discon-
nected couplers (1) as listed in following table. CAUTION:
Never touch terminals of ECM/PCM itself or connect volt-
meter or ohmmeter (2).
CAUTION:
Be sure to connect ohmmeter (2) probe from wire har-
ness side of coupler.
Be sure to turn OFF ignition switch for this check.
Resistance in table represents that when parts temper-
ature is 20°C (68°F).
TERMINALS CIRCUIT STANDARD
RESISTANCECONDITION
E61-9 and E61-2 Main relay 79 – 95 Ω–
E61-22 and C51-3-20 A/C fan motor relay (if equipped) 75 – 110 ΩBattery disconnected
and ignition switch ON
E61-23 and C51-3-20 Fuel pump relay 79 – 95 Ω–
C51-3-6 and Body ground Ground Continuity –
C51-3-17 and Body ground Ground Continuity –
C51-1-1 and Body ground Shift solenoid B (A/T) 11 – 15 Ω–
C51-1-2 and Body ground Shift solenoid A (A/T)
C51-1-4 and C51-3-4 IAC valve (stepper motor coil 2) 25.5 – 33.5 Ω–
C51-1-5 and C51-3-4 IAC valve (stepper motor coil 1)
C51-1-8 and Body ground TCC solenoid (A/T) 11 – 15 Ω–
C51-1-15 and C51-3-4 EVAP canister purge valve 28 – 35 Ω–
C51-1-16 and C51-3-4 IAC valve (stepper motor coil 4) 25.5 – 33.5 Ω–
C51-1-17 and C51-3-4 IAC valve (stepper motor coil 3)
C51-2-1 and C51-3-4 Fuel injector No.2 13 – 16 Ω–
C51-2-2 and C51-3-4 Fuel injector No.1
C51-2-4, C51-2-5 and E61-9 Heater of HO2S-1 5.0 – 6.4 Ω–
C51-2-7 and Body ground Ground Continuity –
C51-2-8 and C51-3-4 Fuel injector No.4 13 – 16 Ω–
C51-2-9 and C51-3-4 Fuel injector No.3
C51-2-12 and C51-3-4 EGR valve (stepper motor coil 4) 20 – 24 Ω–
C51-2-13 and C51-3-4 EGR valve (stepper motor coil 3)
C51-2-14 and C51-3-4 EGR valve (stepper motor coil 2)
C51-2-15 and C51-3-4 EGR valve (stepper motor coil 1)
C51-2-16, C51- 2-17 and
E61-9Heater of HO2S-2 11.7 – 14.3 Ω–
C51-2-21 and C51-3-4 Fuel injector No.6
13 – 16 Ω–
C51-2-22 and C51-3-4 Fuel injector No.5

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-81
TROUBLESHOOTING
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Ignition system inspection :
1) Check spark plug and ignition spark of cylin-
der where misfire occurs, referring to “IGNI-
TION SYSTEM” section.
Is it in good condition?Go to Step 3. Faulty ignition coil, wire
harness, or other system
parts.
3 Fuel injector circuit inspection :
1) Using sound scope, check each injector
operating sound at engine cranking or
idling.
Do all injectors make operating sound?Go to Step 4. Check coupler connec-
tion and wire harness of
injector not making oper-
ating sound and injector
itself.
If OK, substitute a known-
good ECM (PCM) and
recheck.
4 Fuel pressure inspection :
1) Check fuel pressure referring to “TABLE B-
3” in this section.
Is check result satisfactory?Go to Step 5. Repair or replace.
5 Fuel injector inspection :
1) Check fuel injector(s) referring to Section
6E2.
Is check result satisfactory?Go to Step 6. Replace.
6 Ignition timing inspection :
1) Check ignition timing referring to Section
6F2.
Is check result satisfactory?Go to Step 7. Adjust or check system
related parts.
7 EGR system inspection :
1) Check EGR system referring to Section
6E2.
Is check result satisfactory?Go to Step 8. Repair or replace.
8 Fuel level sensor inspection :
1) Check fuel level sensor referring to Section
6E2.
Is check result satisfactory?Go to Step 9. Repair or replace.
9 Check engine mechanical parts or system
which can cause engine rough idle or poor per-
formance.
• Engine compression (See Section 6A2).
• Valve lash or lash adjuster (See Section
6A2).
• Valve timing (Timing belt or chain installa-
tion. See Section 6A2).
Are they in good condition?Check wire harness and
connection of ECM (PCM)
ground, ignition system
and fuel injector for inter-
mittent open and short.Repair or replace.

6-1-88 ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE)
Fig. for Step 45 CMP sensor (REF) signal check :
1) With ignition switch OFF, connect CMP sensor
coupler.
2) Disconnect couplers from ignition coil assembly
and fuel injectors.
3) With ignition switch ON and crankshaft turned
slowly, check voltage between C51-1-13 and
C51-3-26 terminal.
Does voltmeter indicator deflect between 0 – 1 V
and 3 – 5.25 V 4 times while crankshaft turned two
revolutions?Go to Step 6. Faulty “YEL/GRN” wire
or CMP sensor.
If OK, substitute a
known-good ECM
(PCM) and recheck.
6 CMP sensor (POS) signal check :
1) With ignition switch ON and crankshaft turned
slowly, check voltage between C51-1-12 and
C51-3-26 terminal.
Does voltmeter indicator deflect between 0 – 1 V
and 3 – 5.25 V 6 times while crankshaft turned two
revolutions?Poor C51-1-12 and/or
C51-3-13 terminal of
ECM (PCM) coupler con-
nection.
If OK, substitute a
known-good ECM (PCM)
and recheck.Faulty “YEL/BLU” wire
or CMP sensor.
If OK, substitute a
known-good ECM
(PCM) and recheck. Step Action Yes No
1. Disconnected CMP sensor coupler
2. “BLU/BLK” wire (C09-2) terminal
3. “GRY/YEL” wire (C09-1) terminal

ENGINE GENERAL INFORMATION AND DIAGNOSIS (H27 ENGINE) 6-1-91
TROUBLESHOOTING
Step Action Yes No
1 Was “ENGINE DIAG. FLOW TABLE” per-
formed?Go to Step 2. Go to “ENGINE DIAG.
FLOW TABLE” in this
section.
2 Is there DTC P0403 (EGR circuit malfunction)? Go to DTC P0403 Diag.
Flow Table.Go to Step 3.
3 Do you have SUZUKI scan tool? Go to Step 4. Go to Step 6.
4 EGR valve operation check :
1) With ignition switch OFF, install SUZUKI
scan tool.
2) Check EGR system referring to Section
6E2.
Is it in good condition?Go to Step 5. Go to Step 6.
5 MAP sensor check :
1) Check MAP sensor for performance refer-
ring to Section 6E2.
Is check result satisfactory?Intermittent trouble or
faulty ECM (PCM). Check
for intermittent referring to
“INTERMITTENT AND
POOR CONNECTION” in
Section 0A.Repair or replace.
6 EGR valve power supply circuit check :
1) With ignition switch OFF, disconnect EGR
valve coupler.
2) With ignition switch ON, check voltage
between C04-2 and ground, C04-5 and
ground.
Is each voltage 10 – 14 V?Go to Step 7. Faulty “BLU/BLK” wire.
7 EGR valve stepper motor coil circuit check :
1) With ignition switch OFF, connect EGR
valve coupler and disconnect ECM (PCM)
couplers.
2) Check resistance between C51-3-4 and
C51-2-12, C51-2-13, C51-2-14, C51-2-15.
Is each resistance 20 – 24 Ω at 20°C (68°F)?Go to Step 8. Faulty EGR valve.
8 MAP sensor check :
1) Check MAP sensor for performance refer-
ring to Section 6E2.
Is check result satisfactory?EGR passage clogged or
EGR valve malfunction.
If all above are OK, inter-
mittent trouble or faulty
ECM (PCM).
Check for intermittent
referring to “INTERMIT-
TENT AND POOR CON-
NECTION” in Section 0A.Repair or replace.

6A2-10 ENGINE MECHANICAL (H27 ENGINE)
4) Disconnect EGR pipe from right (No.2) bank exhaust mani-
fold if right side exhaust manifold is removed.
5) Remove oil level gauge guide (3) if left side exhaust manifold
is removed.
6) Detach P/S pump assembly as following, if left side exhaust
manifold is removed.
a) Loosen P/S pump drive belt by loosening tensioner bolt.
b) Remove P/S pump mounting bolts.
c) Detach P/S pump assembly (4) with its hoses from cylinder
block.
7) Remove exhaust manifold covers (2) from exhaust manifolds
(1).
8) Hoist vehicle.
9) For 4WD vehicle, before disconnecting front propeller shaft,
put match mark (1) on joint flange and propeller shaft to facil-
itate their installation as shown in the figure.
10) For 4WD vehicle, disconnect propeller shaft from front differ-
ential.
11) Remove exhaust manifold stiffeners (1).
12) Remove stabilizer bar mounting bolt and pull down stabilizer
bar if right side exhaust manifold is removed.
13) Remove exhaust manifolds and their gaskets from cylinder
heads.
1
4
32
2. Exhaust No.1 pipe
A. Without WU-TWC
B. With WU-TWC

6A2-12 ENGINE MECHANICAL (H27 ENGINE)
7) Reverse removal procedure to install front propeller shaft if
removed.
When installing propeller shaft, align match mark (1).
Use following specification to torque universal joint flange.
Tightening torque
Universal joint flange bolt (c) :
55 N·m (5.5 kg-m, 40.0 lb-ft)
8) Connect EGR pipe to left (No.1) bank exhaust manifold (1).
9) Install exhaust manifold covers (2).
10) Install oil level gauge guide (3) using new O-ring.
11) Install P/S pump assembly (4) if it was removed. Refer to
“POWER STEERING PUMP” in Section 3B1.
12) Adjust P/S pump drive belt tension, refer to “POWER
STEERING BELT CHECK AND ADJUSTMENT” in Section
3B1.
13) Connect oxygen sensor lead wire couplers.
Be sure to clamp its lead wires.
14) Connect negative (–) cable to battery.
Upon completion of installation, start engine and check that
no exhaust gas leakage exists.
1
4
32
1. HO2S-1 (Green connector)
2. HO2S-2 (Black connector)