2001 SUBARU LEGACY oil filter

11-4
Always use the proper tools and make certain that they are
well maintained. Never get under the vehicle supported only by a jack. Always
use a safety stands to support the vehicle. Never keep the engine running in a poorly ventilated area,
such as a garage or other closed areas. Do not smoke or allow open flames around the fuel or battery.
This will cause a fire. Because the fuel system is under pressure, replacement of the
fuel filter should be performed only by your SUBARU dealer. Wear adequate eye protection to guard against getting oil or
fluids in your eyes. If something does get in your eyes, thorough-
ly wash it out with clean water. Do not tamper with the wiring of the SRS airbag system or
seatbelt pretensioner system, or attempt to take its connectorsapart, as that may activate the system or it can render it inopera-tive. The wiring and connectors of these systems are yellow for
easy identification. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pretensioner needs service, con-
sult your nearest SUBARU dealer. Before checking or servicing in the engine compart- ment
Always stop the engine and set the parking brake firmly to pre-
vent the vehicle from moving. Always let the engine cool down. Engine parts become very
hot when the engine is running and remain hot for some time af-ter the engine is stopped. Do not spill engine oil, engine coolant, brake fluid or any other
fluid on hot engine components. This may cause a fire. Always remove the key from the ignition switch. When the
ignition switch is in the “ON” position, the cooling fan may oper-
ate suddenly even when the engine is stopped.

Maintenance and service11-7
–
CONTINUED –
Engine compartment overview
2.5 liter models
HBB036BB
1 Manual transmission oil level
g aug e (MT) (p ag e 11-23) or
Differential g ear oil level g aug e
(AT) (p ag e 11-26)
2 Air c leaner element
(p ag e 11-18)
3 Clutc h fluid reservoir
(p ag e 11-32)
4 Automatic transmission fluid
level g aug e (p ag e 11-24)
5 Brake fluid reservoir
(p ag e 11-30)
6 Fuel filter 7
Wind shield washer tank
(p ag e 11-42)
8 Fuse b ox (p ag e 11-46)
9 Battery (p ag e 11-45)
Q Eng ine oil filler c ap
(p ag e 11-9)
W Eng ine c oolant reservoir
(p ag e 11-15)
E Rad iator c ap (p ag e 11-15)
R Eng ine oil level g aug e
(p ag e 11-9)
T Power steering fluid reservoir
(p ag e 11-29)

11-8
3.0 liter models
HBB058BB
1 Air c leaner element
(p ag e 11-18)
2 Differential g ear oil level g aug e
(AT) (p ag e 11-26)
3 Automatic transmission fluid
level g aug e (p ag e 11-24)
4 Brake fluid reservoir
(p ag e 11-30)
5 Fuel filter
6 Wind shield washer tank
(p ag e 11-42) 7
Fuse b ox (p ag e 11-46)
8 Battery (p ag e 11-45)
9 Eng ine c oolant reservoir
(p ag e 11-15)
Q Eng ine oil filler c ap
(p ag e 11-9)
W Eng ine oil level g aug e
(p ag e 11-9)
E Rad iator c ap (p ag e 11-15)
R Power steering fluid reservoir
(p ag e 11-29)

11-10
Changing the oil and oil filter
Chang e the oil and oil filter ac c ord ing to the main tenanc e sc hed ule in
the “Warranty and Maintenanc e Booklet ”.
The eng ine oil and oil filter must b e c hang ed more freq uently than
listed in the maintenanc e sc hed ule when d riving on d usty road s,
when short trip s are freq uently mad e, or when d rivi ng in extremely
c old whether.
1. Warm up the eng ine b y letting the eng ine id le for ab out 10 minutes
to ease d raining the eng ine oil.
2. Park the vehic le on a level surfac e and stop the eng ine.
3. Remove the oil filler c ap .
HBB005BB
4. Drain out the eng ine oil b y removing the d rain p l ug while the en-
g ine is still warm. The used oil should b e d rained into an ap p rop riate
c ontainer and d isp osed of p rop erly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wip e the seating surfac e of the d rain p lug with a c lean c loth and
tig hten it sec urely with a new sealing washer after the oil has c om-
p letely d rained out.

Maintenance and service11-11
–
CONTINUED –
HBB051BB
HBB055BA
HBB054BA
6. Remove three c lip s at the front of the c over und e r the oil filter.
7. Slid e the c over toward the vehic le front to remov e it.
8. Remove the oil filter with an oil filter wrenc h.
9. Before installing a new oil filter, ap p ly a thin c oat of eng ine oil to the
seal.
10. Clean the rub b er seal seating area of the lower c rank c ase and
install the oil filter b y hand turning . Be c areful not to twist or d amag e
the seal.
11. Tig hten it ap p roximately two-third s of a turn a fter the seal makes
c ontac t with the lower c rank c ase.
CAUTION
Never over tighten the oil filter because that can result in an oilleak.

11-1212. Reinstall the c over und er the oil filter.
13. Pour the sp ec ified amount of eng ine oil throug h
the filler nec k.
Oil c ap ac ity: 2.5 liter mod els: 4.2 US q t (4.0 liters, 3.5 Imp q t )
3.0 liter mod els: 6.0 US q t (5.7 liters, 5.0 Imp q t )
14. Start the eng ine and make sure that no oil leak s ap p ear around
the filter ’s rub b er seal.
15. Run the eng ine until it reac hes the normal op er ating temp erature.
Then stop the eng ine and wait a few minutes to allo w the oil d rain
b ac k. Chec k the oil level ag ain and if nec essary, a d d more eng ine oil.
Recommended grade and viscosity CAUTION
Use only engine oil with the recommended grade and viscosity.
Oil grade: API classification SJ or SH with the words “ENERGY
CONSERVING II ” (if you cannot obtain the oil with SJ
or SH grade, you may use SG grade oil.) or the new API certification mark (Starburst mark) dis-
played on the container.
New API Certification Mark (Starburst Mark)API Service label
1
2
3
1 Ind ic ates the oil q uality b y API d esig nations
2 Ind ic ates the SAE oil visc osity g rad e
3 Ind ic ates that the oil has fuel saving c ap ab ilities