2001 Peugeot Partner VU change time

1
11
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for arduous conditions (seethe Maintenance Guide) whichconsist of more frequent services.Note : if the maximum time bet-
ween two oil changes is reachedbefore the mileage is up, the span-ner symbol lights. To change the maintenanceintervals :
- Switch off the ignition. - Press and hold down button
1.
- Switch on the ignition
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated - When the desired maintenance
interval is displayed, press but-ton 1for ten seconds to validate
(the selected maintenance inter-val will flash for ten seconds).
Release the button to validatewhen the display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this ope-
ration after each service. However,if you intend to service the vehicleyourself, the procedure for reset-ting the maintenance indicator isas follows:
- Switch off the ignition.- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Holdbutton 1down for ten
seconds.
- The display will read Ò=0Óand
the spanner will disappear.
29I-14INSTRUMENT PANEL*
* According to model or country.

B
1 - The clockcan be set, with the ignition on and the engine not running , by pressing button B for more than three
seconds; the hour will start to flash.
Changing the time 2 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The hour is memorised, the minutes flash. Long press, rapid scrolling
Changing the minutes 3 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The minutes are set. Long press, rapid scrolling
Note : the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The
clock display goes off after 10 minutes if the driverÕs door remains open.
32I-14INSTRUMENT PANEL*
Digital clock
* According to model or country

1
11
Maintenance intervals If your vehicle is used in particular- ly harsh conditions, it is necessaryto select the maintenance sche-dules for arduous conditions (seethe Maintenance Guide) whichconsist of more frequent services.Note : if the maximum time bet-
ween two oil changes is reachedbefore the mileage is up, the span-ner symbol lights. To change the maintenanceintervals :
- Switch off the ignition. - Press and hold down button
1.
- Switch on the ignition
- The distance remaining until the next service flashes.
- Release the button immediately.
- The maintenance interval is dis- played.
- Pressing button 1briefly allows
the maintenance intervals to be alternated - When the desired maintenance
interval is displayed, press but-ton 1for ten seconds to validate
(the selected maintenance inter-val will flash for ten seconds).
Release the button to validatewhen the display stops flashing. Resetting the maintenance indi- cator to zero
Your dealer will perform this ope-
ration after each service. However,if you intend to service the vehicleyourself, the procedure for reset-ting the maintenance indicator isas follows:
- Switch off the ignition.- Press and hold down button 1.
- Switch on the ignition.
- The distance remaining until the next service flashes.
- Holdbutton 1down for ten
seconds.
- The display will read Ò=0Óand
the spanner will disappear.
29I-14INSTRUMENT PANEL*
* According to model or country.

B
1 - The clockcan be set, with the ignition on and the engine not running , by pressing button B for more than three
seconds; the hour will start to flash.
Changing the time 2 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The hour is memorised, the minutes flash. Long press, rapid scrolling
Changing the minutes 3 - Short press on B, allows the time to be changed slowly.
If the button is not pressed for five seconds : The minutes are set. Long press, rapid scrolling
Note : the clock display comes on when the driverÕs door is opened and goes out one minute after it is shut. The
clock display goes off after 10 minutes if the driverÕs door remains open.
32I-14INSTRUMENT PANEL*
Digital clock
* According to model or country

Direction indicators Left: move the stalk downwards. Right: move the stalk upwards.
To signal a change of direction, move the stalk past the point of resistance. The signal will cancel automatically as the steering wheel returns.
36I-16SIGNALLING
Horn Press the end of the stalk. Headlamp flash Flick the stalk gently towards you.
It is possible to flash the headlamps when the engine is switched off. Hazard warning This operates all the direction indicators at the same time.
Use it only in case of danger,for an emergency stop or in exceptional dri-
ving circumstances.
It can also operate when the ignition is off.The direction indicators will not operate if the vehicle is driven with the hazard warning lights on.

Towbar The installation of a towbar should be carried out by an approved dealer who will know the towing capacity of your
vehicle and have the necessary information on the fitting of such a safety related item. The dealer will also be aware
of any modifications to the vehicleÕs cooling system needed to cater for any arduous towing conditions.
Towing (boat, caravan, etc.)
¥ Before setting off :- check the tyre pressures of both the vehicle and the towed load and check the signalling lamps on the towed load.
- practise manoeuvring, especially reversing.
- regularly grease the towball hitch, remove it when not required.
¥ Spread the load inside the caravan and keep within the weight limits.
¥ Always drive at a moderate speed, Change down to a lower gear in good time before going uphill and downhill. Be aware of the effect of side winds.
¥ Towing increases fuel consumption.
¥ Braking distances are increased. Use the brakes gently and progressively. Avoid harsh braking.
¥ When parking on a slope: as well as following the instructions for operation of the handbrake, make sure that the towbar is properly locked and use wheel chocks if necessary.
106VI-7SAFETY ADVICE
Keep within the towing limits of your vehicle.
In the case of a towing vehicle exceeding its maximum rear axle weight or Gross Vehicle Weight, its speed limit is 60 mph (100 Km/h).
Towing weights: see ÒGENERALÓ.