2001 Peugeot 306 C boot

YOUR 306 CABRIOLET AT A GLANCE
6
FRONT AIRBAGS Disarming the passenger airbag. Insert the ignition key in switch 1
and turn it:
Ð to the ÒONÓposition, the pas-
senger airbag is armed,
Ð to the ÒOFFÓposition, the pas-
senger airbag is not armed.
Operational check This is by means of the warning light on the instru-ment panel.
If the passenger airbag is not armed, the warning light remainson. Always contact your PEUGEOT dealer if the warning light flashes.
THE REMOTE CONTROL
A single press on button Alocks
the doors and boot.
A single press on button Bunlocks
the vehicle.
KEYS
Using the key in the driverÕs door lock will lock or unlock the doorsand boot.
Passenger airbagprecautions
If the passenger airbag is armed or if your vehicle is not fitted with apassenger airbag, the warninglight comes on for 6 seconds whenthe ignition is switched on.For a vehicle fitted with a disarm-ing switch:
Ð disarm theairbag if youinstall arearwards-facing childseat.
Ð arm the airbag whenan adult is inthe seat.
For a vehicle not fitted with a disarming switch:
Ð do not install rear-wards-facingchild seats on thefront passengerseat.
Never place your feet or any object on the fascia.
A
B
103

MAINTENANCE OF YOUR 306 CABRIOLET21
PEUGEOT SERVICING LEVELS A AND C
Level
Operations Description of operations for 1st serviceServicesACIntermediate visit
DRAIN AND REFILL- Engine drain and refill.- Oil filter.
REPLACEMENT- Fuel filter (Petrol).
- Air filter element.
- Spark plugs (Petrol).
- Engine oil (check + top up).
- Manual gearbox oil (check + top up).
- Battery (check + top up) if plug is removable.
LEVEL- Front/rear windscreen wash (check + top up).
- Coolant (check + top up).
- Brake fluid (check + top up).
- Power steering fluid (check + top up according to specification).
- Operation of lights and indicators.
- Condition of glass, headlamp and light lenses and mirrors.
- Horn.
- Windscreen washer jets.
- Condition of wiper blades.
- Condition and tension of ancillary drive belts.
- Handbrake.
- Condition of hydraulic circuits (hoses and covers), check for leaks.
CHECK- Condition of rubber boots and gaiters.
- Brake pad wear.
- Clearances, hubs, rods, ball joints, flxible mountings.
- Sealing of dampers.
- Wear of rear linings.
- Condition and pressure of tyres (including spare wheel).
- Emission control check according to current legislation (Petrol).
- Pollen filter check (according to specification).
- Visual check of the whole vehicle by a PEUGEOT dealer.
ROAD TEST
: All driving conditions : Specific conditions

ELECTRIC HOOD: CLOSING Inside the vehicle:
- Turn the ignition key to position M
(engine not running, oil pressure warning light on) and lower thefront windows.
- Press the switch 4on the central
console until the operation hasbeen completed (hood unfoldeduntil it stops not quite flush withthe windscreen). Using the centre handle and a sidehandle, fold down the front of thehood, position the side handle hooksin their housings and secure the twohandles. As a safety precaution,opening and closingoperations must be car-
ried out when stationary.Driving with the hood
cover open is prohibited.
If the boot is not closed, the hood
cannot be opened or closed.
If the front of the hood is not
closed, the hood cannot be
opened.
Do not carry out too many opera-
tions in succession as there is a
risk that the battery may become
flat.
Do not place anything in the com-
partment reserved for storing the
hood as there is a risk of damage.
Before opening the hood:
- Ensure that the hood and rear screen are clean.
- Ensure that the hood is dry, otherwise the compression it is
subjected to when it is folded
will result in marks or even
stains caused by moisture over
time.
YOUR 306 CABRIOLET IN DETAIL 47
4

If an electrical fault occurs whilethe hood is open, it is possible to close it manually.
Using the side handle 1, raise the
hood and unfold it to the point of resistance.
- Raise the rear of the hood.
- Close the hood cover and secure it by turning the wheelbrace Ba
quarter turn anti-clockwise.
- Fold down the rear of the hood on the hood cover. - From inside the vehicle, using the
centre handle and a side handle, fold down the front of the hood,position the side handle hooks intheir housings and secure the twohandles.
If the fault persists, contact your
PEUGEOT dealer.
YOUR 306 CABRIOLET IN DETAIL
48
A
B
1
ELECTRIC HOOD:
MANUAL CLOSING Open the boot, remove the cap
A.
Using the wheelbrace B, turn a quar-
ter turn clockwise in order to release the hood cover and open it.

- Release the two front side handles13 .
- Remove the hard top and careful- ly place it on a clean and stable stand. - From the boot, manually open the
hood cover 10. To do this, remove
the cap and turn the control aquarter turn clockwise using thewheelbrace. Remove the wheel-brace, close the boot and hold thehood cover 10open using the sec-
ond strap 2.
- Remove the two side brackets 12
using the 17 mm flat spanner 6.
- Connect connector 8to the har-
ness connector located behind theside flap 14on the right hand side
of the rear shelf (if the connectionis not made, the hood and blowerwill not operate).
- Remove the retaining straps 2
from the hood cover 10and from
the side flaps 7.
- Close the hood cover 10manually.
- Switch on the ignition.
- Close the hood and the windows. Before folding the hood into its housing, ensurethat it has been brushedand dried to remove any
moisture and that the rear screen
is folded correctly.
To prevent damage to the hood cover and the boot, the boot mustbe closed during the hood coverlowering and raising operations. Although the hood cover may appear to support itself in the ver-tical position, it must be securedusing a strap.
Take extreme care when handling the hard top to avoid scratching ordamaging it. Do not lean the hard top against a wall or place it in an unstableposition. Store the hard top on a stand in a clean, dry environment and coverit. When the hood has been folded for a long time, ask a PEUGEOTdealer to remove any creases. Imperative The hard top heated rear screen harness must be connected at alltimes. If the harness is not con-nected significant damage mayresult from accidental operation.
The ignition must be switched off for all operations.
(except during the hood cover manoevring phase for the electric hood).
YOUR 306 CABRIOLET IN DETAIL 51
12
13
10
2

- Remove the retaining strap 2from
the hood cover 10.
- From the boot, close the hood cover 10manually. To do this,
remove the cap and turn the con- trol a quarter turn anti-clockwiseusing the wheelbrace. Removethe wheelbrace, reposition the capand close the boot.
Take care not to trap the harness.
- Carefully position the hard top: place the front edge of the roof incontact with the seal of the uppersection of the windscreen. Position the rear section of the roof on the side brackets 12.
Switch on the ignition. Open all the windows.
Lower the hood completely.
Switch off the ignition.Open the hood cover Place the restraining straps
2on the
two side flaps 7and the hood cover
10 .
- Secure the two side brackets 12to
the vehicle using the 17mm span- ner 6.
- Disconnect connector 8from the
harness located behind the sideflap 14on the right hand side of
the rear shelf.
HARD-TOP: REFITTING
Tools
Your hard-top is supplied with a tool kit containing: 1
- A storage case.
2 - Two retaining straps.
3 - A screwdriver with two heads.
4 - A pair of gloves.
5 - A special spanner.
6 - A 17mm flat spanner.
WARNINGThe removal-refitting operations described below should have beendemonstrated by your PEUGEOTdealer on handover of your vehicle. If your hard-top was supplied as
an accessory, the first removaloperation must be carried out by
an approved dealer. The opera-tion must be carried out by threepeople.
YOUR 306 CABRIOLET IN DETAIL
52
6
3
5 1 4
2
10
14
2
82
7
5
12

- Fit the covers 11in place and
screw them in.
- Check that the window seals are positioned correctly.
- Switch on the ignition and close the windows.
- Secure the two front side handles
13 .
- Secure the hard top on the side brackets 12using the special
spanner 5(a quarter turn).
- Connect connector 8to the hard
top heated rear screen harness.
- Remove the restraining strap 2
from the side flaps 7. Before folding the hood into its housing, ensurethat it has been brushedand dried to remove anymoisture and that the
rear screen is folded correctly.
To prevent damage to the hood cover and boot, the boot must beclosed during the hood cover low-ering and raising operations. Although the hood cover may appear to support itself in the ver-tical position, it must be securedusing a strap. Handle the hard top carefully so as not to damage the seal.
Take extreme care when handling the hard top to avoid scratching ordamaging it. Do not lean the hard top against a wall or place it in an unstableposition. Store the hard top on a stand in a clean, dry environment and coverit. When the hood has been folded for a long time, ask a PEUGEOTdealer to remove any creases. Imperative The hard top heated rear screen harness must be connected at alltimes. If the harness is not con-nected, significant damage mayresult from accidental operation.
The ignition must be switched off for all operations
(except during the hood cover manoeuvring phase for the electric hood).
YOUR 306 CABRIOLET IN DETAIL 53
11
13

YOUR 306 CABRIOLET IN DETAIL
78
THE REMOTE CONTROL
A single press on button Alocks the
doors and boot, this is displayed by the direction indicators staying on forabout 2 seconds.
A single press on button Bunlocks
the vehicle, this is displayed by the
direction indicators flashing rapidly.
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot. If either of the front doors is notclosed, the central locking will notwork. CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR
1620/3 volt
battery). If the remote control does not work after the battery has been changed,re-programme the remote control. PROGRAMMING THE REMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: Do not repeatedly press the button of your remote control out of range of
your vehicle. You risk causing it not towork and the remote control wouldhave to be reprogrammed.
A
B