2001 Oldsmobile Intrigue ignition

2-71
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running. If the light doesn't come on, have it repaired.
This light will also come on during a malfunction in
one of two ways:

Light Flashing
-- A misfire condition has been
detected. A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service may be required.

Light On Steady
-- An emission control system
malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.
If the Light Is Flashing
The following may prevent more serious damage to
your vehicle:

Reducing vehicle speed.

Avoiding hard accelerations.

Avoiding steep uphill grades.

If you are towing a trailer, reduce the amount of
cargo being hauled as soon as it is possible.If the light stops flashing and remains on steady, see ªIf
the Light Is On Steadyº following.
If the light continues to flash, when it is safe to do so,
stop the vehicle. Find a safe place to park your vehicle.
Turn the key off, wait at least 10 seconds and restart the
engine. If the light remains on steady, see ªIf the Light
Is On Steadyº following. If the light is still flashing,
follow the previous steps, and drive the vehicle to your
dealer or qualified service center for service.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. See ªFilling Your Tankº in the Index.
The diagnostic system can determine if the fuel cap
has been left off or improperly installed. A loose or
missing fuel cap will allow fuel to evaporate into the
atmosphere. A few driving trips with the cap properly
installed should turn the light off.
Did you just drive through a deep puddle of water?
If so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out. A few driving trips should turn the light off.

2-73 Oil Warning Light
If you have a problem with
your oil, this light may stay
on after you start your
engine or come on
when you are driving.
This indicates that oil is not going through your engine
quickly enough to keep it lubricated. The engine could
be low on oil or could have some other oil problem.
Have your vehicle serviced immediately.
The oil light could also come on when the ignition is on
but the engine is not running. This is normal. The light
comes on as a test to show you it's working, but the light
should go out when you turn the ignition to ON. If it
doesn't come on with the ignition on, you may have a
problem with the fuse or bulb. Have it fixed right away.CAUTION:
Don't keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.
NOTICE:
Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.

2-74 Service Vehicle Soon Light
This light will come on
briefly when the ignition
is turned to ON to show
that the bulb is working.
This light indicates problems with your vehicle that are
not related to emissions.
These problems may not be obvious and may affect
vehicle performance and durability. Consult your dealer
for necessary repairs to maintain vehicle performance.
Low Oil Level Light
Your engine is equipped
with an oil level monitoring
system. When the ignition
is turned to ON, the LOW
OIL light will briefly
come on.
If the light does not flash, have it fixed so it will be
ready to warn you if there's a problem.
If the light stays on, stop the vehicle on a level surface
and turn the engine off. Check the oil level using the
engine oil dipstick. (See ªEngine Oilº in the Index.)
The oil level monitoring system only checks oil level
during the brief period between key on and engine
crank. It does not monitor engine oil level when the
engine is running. Additionally, an oil level check is
only performed if the engine has been turned off for
an extended period of time, allowing the oil normally
in circulation to drain back into the oil pan.

2-76 Low Washer Fluid Light
This light appears when
your vehicle is low on
windshield washer fluid.
This light will come on when your ignition is turned on
to check the bulb. It will go out after a few seconds.
If the light does not come on when you start your
vehicle, the bulb may need to be replaced. See your
dealer to have it fixed right away.
If this light appears while you're driving, your vehicle is
low on washer fluid. Be sure to refill the tank as soon
as possible so that you'll have washer fluid available
when you need it.
Fuel Gage
United States Canada
Your fuel gage tells you about how much fuel you have
left when the ignition is on.
When the indicator nears empty, you still have a little
fuel left, but you should get more soon.

2-77
Here are four things that some owners ask about. All
these things are normal and do not indicate a problem
with the fuel gage:

At the gas station, the gas pump shuts off before the
gage reads full.

It takes more (or less) fuel to fill up than the gage
reads. For example, the gage reads half full, but it
takes more (or less) than half the fuel tank's capacity
to fill it.

The gage pointer may move while cornering, braking
or speeding up.

The gage may not indicate empty when the ignition
is turned off.Low Fuel Light
United States Canada
If your vehicle is low on fuel, this warning light near the
fuel gage will come on.
It will also come on for a few seconds when you first
turn on the ignition as a check to show you it's working.
If it doesn't come on then, the bulb may need to be
replaced. See your dealer to have it fixed right away.

3-9
Ventilation
For mild outside temperatures when little heating or
cooling is needed, use UPPER, ECON and OUTSIDE
AIR to direct outside air through your vehicle. Your
vehicle also has the flow
-through ventilation system
described later in this section.
Defogging and Defrosting
Your system has two settings for clearing the front and
side windows. To defrost the windows quickly, use your
DEFROST button. To warm passengers while keeping
the windows clean, use DEFOG by pressing the
MODE button.
Rear Window Defogger
The rear window defogger
uses a warming grid to
remove fog from the rear
window. Press the button to
turn the defogger on. It will
turn itself off after about
15 minutes (automatic
control) or 10 minutes
(manual control).If you turn it on again, the defogger will only run for
about seven and one
-half minutes (automatic control) or
five minutes (manual control) before turning off. You
can also turn it off by turning off the ignition or pressing
the button again.
Do not attach anything like a temporary vehicle license
or decal across the defogger grid.
NOTICE:
Don't use a razor blade or something else sharp
on the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.

3-11
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all its controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Setting the Clock
Press and hold HR until the correct hour appears.
The letter A or P may appear on the display for AM
or PM. Then, press and hold MN until the correct
minute appears. The clock may be set with the
ignition on or off.
AM-FM Stereo with Cassette Tape Player
and Automatic Tone Control
Playing the Radio
PWR VOL: Press this knob to turn the system on and
off. To increase volume, turn the knob clockwise. Turn
it counterclockwise to decrease volume.

3-12
RCL: Press this button briefly to recall the station being
played or to display the clock. To change what is
normally shown on the display (station or time), press
the RCL button until you see the display you want, then
hold the RCL button until the display flashes. If you
press the button when the ignition is off, the clock will
show for a few seconds.
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back into its stored
position when you're not using it.
SEEK: Press the up or down arrow to go to the next
higher or lower station and stay there. The sound will
mute while seeking.
SCAN: Press this button and release it to listen to
stations for a few seconds. The radio will go to a station,
stop for a few seconds, then go on to the next station.
Press the button again to stop scanning. The sound will
mute while scanning, and SCAN will appear on the
display. If you press SCAN for more than two seconds,
the radio will change to P SCAN mode. P SCAN will
appear on the display.PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations. You can set up to
15 stations (five AM, five FM1 and five FM2). Just do
the following:
1. Turn the radio on.
2. Press AM FM to select the band.
3. Tune in the desired station.
4. Press TONE to select the equalization that best suits
the type of station selected.
5. Press and hold one of the five numbered buttons.
The sound will mute. When it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the tone that
you selected will also be automatically selected for
that button.
6. Repeat the steps for each pushbutton.
P SCAN: Press SCAN for more than two seconds, and
P SCAN will appear on the display. The radio will go to
the first preset station stored on your pushbuttons, stop
for a few seconds, then go on to the next preset station.
Press SCAN again to stop scanning.