2001 Oldsmobile Aurora ignition

3-2
Comfort Controls
This section tells you how to operate your climate
control system.
Your vehicle may be equipped with a passenger
compartment air filter. For more information, see
ªPassenger Compartment Air Filterº in the Index.
Comfort Controls Personalization
(If Equipped)
This feature allows two different drivers to store and
recall their own climate control settings for temperature,
air delivery mode and fan speed. The personal choice
settings recalled are determined by the transmitter used
to enter the vehicle. After the button with the unlock
symbol on a remote keyless entry transmitter is pressed,
and the ignition is in RUN, the climate control will
adjust to the last settings of the identified driver. The
settings can also be changed by pressing one of the
memory buttons (1 or 2) located on the driver's door,
until you hear two beeps. When adjustments are made,
the new settings are automatically saved for that driver.
Automatic Electronic Climate Control
Your vehicle is equipped with either a Single Zone or
a Dual Zone Automatic Electronic Climate Control
System. You can use the automatic setting or override
the automatic setting by using the manual controls.
Your vehicle also has the flow
-through ventilation
system described later in this section.
AUTO
-PUSH Knob
By pressing the AUTO
-PUSH knob, you have
selected the electronic climate control system to be in
the automatic mode. The climate control system will
automatically control the air temperature, air inlets, air
distribution and the fan speed based on your selected
temperature setting as well as on the temperature inside
the vehicle, the outside temperature and the sun load.

3-6
RECIRC: Press this button to limit the amount
of outside air entering your vehicle. This is helpful when
you are trying to cool the interior of the vehicle quickly
or limit the amount of outside air entering your vehicle
for some other reason. The RECIRC button and the
AUTO
-PUSH knob may be selected at the same time.
The system will remain in RECIRC until the ignition
is turned off, then the system will return back to the
previously selected mode. RECIRC may be selected
in all manual airflow modes except front defrost.
When the weather is cool or damp, operating in
RECIRC for extended periods of time may cause
fogging of the vehicle's windows. To clear the fog,
switch back to outside air by turning off RECIRC,
select either DEFOG or front defrost mode and increase
the fan speed. To avoid refogging of the windows,
minimize your use of RECIRC under these conditions
and turn the A/C on to help dehumidify the air.
A/C: Press this button to turn the air conditioning
compressor on and off. If the system is operating in
the automatic mode, the A/C indicator light will
automatically illuminate. In the auto mode, the
A/C compressor will only operate when the system
determines it is needed.OFF: Turn the AUTO
-PUSH knob to OFF. Turning
the system off will cause the fan to turn off and the
airflow to be directed out the lower floor outlets. The
system will still try to keep the interior of the vehicle
at the previously chosen comfort setting. The outside
temperature will show in the display when the system
is set to OFF.
Air Conditioning
The air conditioner cools and dehumidifies the air for
the inside of the vehicle.
The air conditioning compressor is enabled in all
modes unless the A/C button is in the off position
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When
the air conditioner is on, you may sometimes notice
slight changes in your vehicle's engine speed and power.
This is normal, because the system is designed to cycle
the compressor on and off to keep the desired cooling
and help fuel economy.

3-8 Rear Window Defogger
REAR: Press this
button to warm the
defogger grid on the
rear window. An
indicator light below
the button will glow
while the rear window
defogger is operating.
At speeds above 30 mph (48 km/h), the rear defogger
will stay on until you press the REAR button again.
At speeds below 30 mph (48 km/h), the rear window
defogger will turn off automatically after about
10 minutes of use. If you press it again, the defogger
will operate for about five minutes only. You can also
turn the defogger off by turning off the ignition.
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
When you operate the rear window defogger, the outside
rearview mirrors are also heated to help remove ice and
fog if your vehicle is equipped with heated outside
rearview mirrors. For more information see ªHeated
Outside Rearview Mirrorº in the Index.
NOTICE:
Don't use a razor blade or something else sharp
on the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Passenger Temperature Control (Option)
With this feature, the right
front seat passenger can
control the comfort setting
for their own zone. To use
this feature, turn the knob
on the passenger's door to
a cooler or warmer setting.
The temperature can be set up to 8
F (4
C) cooler or
warmer than the main setting.

3-10 Steering Wheel Controls for Climate Control
Some heating and cooling
controls can be adjusted
at the steering wheel.
Other touch controls
also operate some audio
controls. See ªAudio
Steering Wheel Controlsº
later in this section.
Press the upper part of the fan symbol button to override
the automatic fan control and increase the fan speed.
Press the lower part of the fan symbol button to override
the automatic fan control and reduce the fan speed.
Press either arrow on the TEMP button once to display
your current comfort setting in the digital display. Press
the upper part of the TEMP button again to provide a
warmer comfort setting or press the lower part of the
TEMP button again to provide a cooler comfort setting.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all its controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Setting the Clock
Press and hold HR until the correct hour appears. The
letters AM or PM will appear on the display. Then, press
and hold MN until the correct minute appears. The clock
may be set with the ignition on or off. In addition, the
clock can also be automatically set, when tuned to an
RDS station that is broadcasting time, by pressing and
holding the HR and the MN button at the same time.
The display will show TIME UPDATED. If there is no
time available, NO UPDATE will be displayed.

3-15
ALERT!: This type of announcement warns of national
or local emergencies. You will not be able to turn off
alert announcements. ALERT! appears on the display
when an alert announcement plays. When an alert
announcement comes on the tuned radio station, you
will hear it, even if the volume is muted or a cassette
tape or compact disc is playing. If the cassette tape or
compact disc player is playing, play will stop for the
announcement and resume when the announcement
is finished.
ALTERNATE FREQUENCY: This feature allows
the radio to switch to a stronger station with the same
broadcast. Press and hold AM
-FM for two seconds to
turn alternate frequency on. AF ON will appear on the
display. The radio may switch to stronger stations with
the same broadcast. Press and hold AM
-FM again for
two seconds to turn alternate frequency off. AF OFF
will appear on the display. The radio will not switch to
other stations. When you turn the ignition off and
then on again, the alternate frequency feature will
automatically be turned on.Adjusting the Speakers
BAL
-FADE: The AUDIO button adjusts balance and
fade. To adjust balance, press and hold the AUDIO
button until BAL appears on the display. Turn the knob
to adjust the sound to the left or right speakers. The
middle position balances the sound between the speakers.
To adjust fade, press and hold the AUDIO button until
FAD appears on the display. Turn the knob to adjust the
sound to the front or rear speakers. The middle position
balances the sound between the speakers.
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this
player. The longer side with the tape visible should face
to the right. If the ignition is on, but the radio is off, the
tape can be inserted and will begin playing. If you hear
nothing but a garbled sound, the tape may not be in
squarely. Press EJECT to remove the tape and start over.

3-16
While the tape is playing, use the VOL, FAD, BAL,
TREB, MID, BASS, AUTO EQ, SEEK and SCAN
controls just as you do for the radio. The display will
show TAPE and an arrow showing which side of the tape
is playing. The tape player automatically begins playing
the other side when it reaches the end of the tape.
Your tape bias is set automatically when a metal or
chrome tape is inserted. If you want to insert a tape
when the ignition is off, first press EJECT or the
RCL button.
If an error appears on the radio display, the tape won't
play because of an error.
TIGHT TAPE is displayed when the tape is tight and the
player can't turn the tape hubs. Remove the tape. Hold
the tape with the open end down and try to turn the right
hub counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape may
be damaged and should not be used in the player. Try a
new tape to make sure your player is working properly.
BROKEN TAPE is displayed when the tape is broken.
Try a new tape.
WRAPPED is displayed when the tape is wrapped
around the tape head. Attempt to get the cassette out.
Try a new tape.If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer. If your radio
displays an error message, write it down and provide
it to your dealer when reporting the problem.
REV (1): Press this button to reverse the tape rapidly.
Press it again to return to playing speed. The radio will
play the last selected station while the tape reverses. You
may select stations during REV operation by using the
TUNE knob.
FWD (2): Press this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last selected
station while the tape advances. You may select stations
during FWD operation by using the TUNE knob.

(3): Press this button to reduce background noise.
DOLBY B ON will appear on the display with the
Dolby icon. Press it again to turn Dolby off.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation.
Dolby and the double
-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.
SIDE (5): Press this button to play the other side
of the tape.

3-17
AUTO EQ: Press AUTO EQ to select the desired
preset equalization setting while playing a cassette tape.
The equalization will be automatically set whenever you
play a cassette tape.
SEEK: Press the up or down arrow to search for the next
or previous selection on the tape. Your tape must have at
least three seconds of silence between each selection for
SEEK to work. You can skip nine selections up or down
on the tape. Choose how many selections you want to
skip. Press the SEEK arrow that many times. The number
of selections to be skipped will appear on the display.
SCAN: Press and hold the SEEK button for more than
two seconds until you hear a beep and SCAN appears
in the display. Use SCAN to listen to each selection for a
few seconds. The tape will go to the next selection, stop
for a few seconds, then go on to the next selection.
Press this button again to stop scanning.
AM
-FM: Press this button to play the radio when
a tape is in the player. The tape will stop but remain in
the player.TP
-CD: With a compact disc in the player and the
radio playing, press this button to play a compact disc.
Press AM
-FM to return to the radio when a compact
disc is playing. Press TP
-CD to switch between the
tape and compact disc if both are loaded. The inactive
tape or CD will remain safely inside the radio for future
listening. The display will show TAPE and CD icons.
If you have the optional CD changer and the CD
changer is loaded, the TP
-CD button will activate the
changer and an icon will be lit in the display.
EJECT: Press this button to remove the tape. The
radio will play. EJECT may be activated with either the
ignition or radio off. Cassettes may be loaded with the
radio and ignition off if this button is pressed first.
CLEAN PLAYR: If this message appears on the
display, the cassette tape player needs to be cleaned.
It will still play tapes, but you should clean it as soon
as possible to prevent damage to the tapes and player.
See ªCare of Your Cassette Tape Playerº in the Index.
After you clean the player, press and hold EJECT for
five seconds to reset the CLEAN PLAYR indicator.
The radio will display CLEANED to show the indicator
was reset.

3-18
Playing a Compact Disc
With the ignition on, insert a disc partway into the slot,
label side up. The player will pull it in and the disc
should begin playing. If you want to insert a CD when
the ignition is off, first press EJECT or the RCL knob.
Note that when the disc is inserted, the CD symbol will
be displayed. If you select an EQ setting for your CD,
it will be activated each time you play a CD.
As each new track starts to play, the track number will
appear on the display.
If CHECK CD appears on the radio display and the disc
comes out, it could be that:

The road is too rough. The disc should play when
the road is smoother.

The disc is dirty, scratched, wet or upside down.

The air is very humid. If so, wait about an hour
and try again.
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer. If your radio
displays an error message, write it down and provide it
to your dealer when reporting the problem.REV (1): Press and hold this button to reverse quickly
within a track. You will hear sound at a reduced volume.
The display will show elapsed time. Release it to play
the passage.
FWD (2): Press and hold this button to advance quickly
within a track. You will hear sound at a reduced volume.
The display will show elapsed time. Release it to play
the passage.
RDM (4): Press this button to hear the tracks in random,
rather than sequential, order. RDM and the track number
will appear on the display.
AUTO EQ: Press AUTO EQ to select the desired
preset equalization setting while playing a compact disc.
The equalization will be automatically set whenever you
play a compact disc.
SEEK: Press the reverse arrow while playing a CD to
go to the start of the current track if more than eight
seconds have played. Press the forward arrow to go to
the next track. If you hold the button or press it more
than once, the player will continue moving backward or
forward through the disc.