2001 Oldsmobile Aurora light

2-20
To program the new key:
1. Insert the current driver's key (black in color) in the
ignition and start the engine. If the engine will not
start, see your dealer for service.
2. After the engine has started, turn the key to LOCK,
and remove the key.
3. Insert the key to be programmed and turn it to RUN
within 10 seconds of removing the previous key.
4. The SECURITY telltale light will turn off once the
key has been programmed. It may not be apparent
that the SECURITY light went on due to how
quickly the key is programmed.
5. Repeat Steps 1 through 4 if additional keys are
to be programmed.
If you are ever driving and the SECURITY light comes on
and stays on, you will be able to restart your engine if you
turn it off. Your PASS
-Key III system, however, is not
working properly and must be serviced by your dealer.
Your vehicle is not protected by the PASS
-Key III system
at this time.
If you lose or damage a PASS
-Key III key, see your
dealer or a locksmith who can service PASS
-Key III to
have a new key made.
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate ªbreak-in.º
But it will perform better in the long run if you
follow these guidelines:

Don't drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Don't tow a trailer during break
-in.
See ªTowing a Trailerº in the Index for
more information.

2-21
Ignition Positions
With the ignition key in the ignition switch, you can turn
the switch to four different positions.
LOCK (A): This is the only position in which you
can remove the key. This position locks your ignition,
steering wheel and transaxle. It's a theft
-deterrent feature.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
ACCESSORY (B): This position lets you use your
electrical power accessories such as power windows,
power sunroof (option), radio and the windshield wipers.
RUN (C): This is the position the switch returns to after
you start your engine and release the switch. This is the
position for normal driving. Even when the engine is not
running, you can use RUN to operate your electrical
power accessories and to display some instrument panel
warning lights.
START (D): This position starts your engine. When
the engine starts, release the key. The ignition switch
will return to RUN for normal driving.

2-22 Key Reminder Warning
If you leave your key in the LOCK ignition position,
you will hear a warning chime when you open the
driver's door.
Always leave your key in LOCK. If you leave it in any
other position, you will drain the battery power.
Retained Accessory Power (RAP)
After you turn the ignition off and remove the key, you
will still have electrical power to accessories such as the
power windows, audio steering wheel controls, clock,
sunroof (option), accessory power outlet and the radio
for up to 10 minutes. The instrument panel cluster lights
will stay on for a few seconds, then go out. Once you
open a door, the power will shut off.
Starting Your Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's
a safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transaxle. Shift to PARK (P) only when your
vehicle is stopped.

2-29
Parking Brake
Your vehicle has a PUSH
TO RELEASE parking
brake. To set the parking
brake, hold the regular
brake pedal down with
your right foot. Push down
the parking brake pedal
with your left foot.
If the ignition is on, the brake system warning light
will come on while the parking brake is set and a single
chime will be heard.To release the parking brake, hold the regular brake
pedal down with your right foot and push the parking
brake pedal with your left foot. This will release the
parking brake pedal. When you lift your left foot, the
parking brake pedal will follow it to the release position.
If you try to drive approximately 20 feet (6.1 m) with
the parking brake on, the brake light stays on and a
chime sounds until you release the parking brake.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.
If you are towing a trailer and are parking on any hill,
see ªTowing a Trailerº in the Index. That section
shows what to do first to keep the trailer from moving.

2-36
As you signal a turn or a lane change, if the arrows
flash very fast, a bulb may be burned out and other
drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in the
Index) and for burned
-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON? reminder message. To turn off the chime and
message, move the turn signal lever to the off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC.
Headlamps
The headlamp control
is located on the turn
signal/multifunction lever.
Turn the control to this symbol to turn on
the following:

Parking Lamps

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights

2-37
Turn the headlamp control to this symbol to turn on
the following:

Headlamps

Parking Lamps

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights
Turning the headlamp control to AUTO will turn the
headlamps, taillamps and parking lamps on and off,
while the ignition is on, by sensing how dark it is outside.
Turn the headlamp control back to off to turn all of the
lamps off.
Wiper
-Activated Headlamps
This feature turns on the low
-beam headlamps,
instrument panel cluster backlighting, and taillamps
when it is bright enough outside, the headlamp control
is in AUTO and after the windshield wipers have been
in use for approximately six seconds.To operate the wiper
-activated headlamps the headlamp
control must be in AUTO. If the wiper
-activated
headlamps are on and the ignition switch is turned to
RUN, the wiper
-activated headlamps will continue.
When you turn the key to LOCK, the wiper
-activated
headlamps will immediately turn off. The wiper
-activated
headlamps will also turn off if you turn the headlamp
switch to OFF or turn off the windshield wipers.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high,
push the lever away from you until you hear a click.
Then release it.
When the high beams
are on, this light on the
instrument panel cluster
will also be on.
If the fog lamps are on when you turn on the
high
-beam headlamps, the fog lamps will turn off.
The fog lamps will turn back on when you turn off the
high
-beam headlamps.

2-39 Windshield Wipers
The lever on the right side of your steering column
operates your windshield wipers.
If your windshield wipers are on for more than
six seconds while you are driving, the low
-beam
headlamps, instrument panel cluster backlighting and
the taillamps will turn on. For more information see
ªWiper
-Activated Headlampsº in the Index.
For a single wiping cycle, move the lever down to MIST.
Hold it there until the wipers start, then release it. The wipers will stop after one cycle. If you want more
cycles, hold the lever to MIST longer.
For steady wiping at low speed, move the lever up to
the LO position. For high
-speed wiping, move the
lever up further, to HI. To stop the wipers, move the
lever to OFF.
You can set the wiper speed for a long or short delay
between wiper cycles. This can be very useful in light
rain or snow. Move the lever up to the first detent, INT.
Turn the band labeled INT ADJ down towards the
shorter lines for fewer wiper passes per minute. As you
turn the band towards the longer lines, the wiper cycles
per minute will increase.
Remember that damaged wiper blades may prevent
you from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they're frozen to the
windshield, carefully loosen or thaw them. If your
blades do become damaged, get new blades or blade
inserts. See ªWindshield Wiper Blade Replacementº
in the Index.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.

2-42
If your vehicle is in cruise control when the traction
control system begins to limit wheel spin, the cruise
control will automatically disengage. See ªTraction
Control Systemº in the Index. When road conditions
allow you to safely use it again, you may turn the cruise
control back on.
Setting Cruise Control
CAUTION:
If you leave your cruise control switch on when
you're not using cruise, you might hit a button
and go into cruise when you don't want to. You
could be startled and even lose control. Keep the
cruise control switch off until you want to use
cruise control.
1. Push the cruise control switch located at the end of
the lever in to ON.
2. Get up to the speed you want.
3. Push the lever down to SET
-CST and release it.
The CRUISE light on the instrument panel cluster
will come on.
4. Take your foot off the accelerator pedal.