2001 Oldsmobile Aurora dic

2-12
Security Feedback
This feature provides feedback to the driver when the
vehicle receives a command from the remote lock
control transmitter and all doors are closed. The
following settings can be programmed for each of
the remote lock control transmitters:

No feedback when locking or unlocking vehicle.

Parking lamps and the Daytime Running Lamps
will flash twice when unlocking the vehicle and flash
once when locking the vehicle.

Horn chirps when all doors are unlocked (second
unlock button press) and when locking the vehicle.

Parking lamps and the Daytime Running Lamps
will flash twice each time the button with the unlock
symbol is pressed; the horn chirps when all doors are
unlocked. Parking lamps and the exterior lamps flash
once and the horn chirps when locking the vehicle.
You must program this feature through the Driver
Information Center (DIC). See ªDIC Personalization
Programmingº in the Index.Matching Transmitter(s) to Your Vehicle
Each remote lock control transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring
any remaining transmitters with you when you go to
your dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.
See your dealer to match transmitters to another vehicle.
Battery Replacement
Under normal use, the battery in your remote lock
control transmitter should last about two years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.

2-13
NOTICE:
When replacing the battery, use care not to
touch any of the circuitry. Static from your
body transferred to these surfaces may damage
the transmitter.
For battery replacement, use a Duracell
battery, type
DL
-2032, or a similar type.To replace the battery:
1. Insert a coin into the notch near the key ring. Turn
the coin counterclockwise to separate the two halves
of the transmitter.
2. Once the transmitter is separated, use a pencil eraser
to remove the old battery. Do not use a metal object.
3. Replace the battery as the instructions under the
cover indicate.
4. Snap the transmitter back together tightly to be sure
no moisture can enter.
5. Test the operation of the transmitter with your
vehicle. If the transmitter does not work,
resynchronize the transmitter.

2-36
As you signal a turn or a lane change, if the arrows
flash very fast, a bulb may be burned out and other
drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in the
Index) and for burned
-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON? reminder message. To turn off the chime and
message, move the turn signal lever to the off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC.
Headlamps
The headlamp control
is located on the turn
signal/multifunction lever.
Turn the control to this symbol to turn on
the following:

Parking Lamps

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights

2-45
With your headlamp control in AUTO when it is
dark enough outside, your low
-beam headlamps will
automatically come on. The other lamps that turn on
with your headlamps will also turn on. When it is bright
enough outside, the regular lamps will go off, and your
high
-beam headlamps change to the reduced brightness
of DRL.
To turn off all exterior lighting at night when you are
parked, turn the headlamp control all the way toward
OFF. The DRL will turn on automatically and the
HEADLAMPS SUGGESTED message will be
displayed on the DIC when you move the transaxle
out of PARK (P).
If the headlamp control is in the parking lamps position
at night, only the parking lamps will be on. If the
transaxle is out of PARK (P), only the parking lamps
will be active and the HEADLAMPS SUGGESTED
message will be displayed on the DIC.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Headlamps
The automatic headlamps will keep your headlamps on
when it is dark outside and the ignition is in RUN.
It's possible that your headlamps may go out if you
drive from a dark area into a bright area like a lighted
parking lot. If this happens, turn on your headlamps
with the regular headlamp switch.
Light Sensor
Your automatic headlamps and Daytime Running Lamps
work with the light sensor on top of the instrument
panel. Don't cover it up. If you do it will read ªdarkº
and the automatic headlamp lighting will turn on.
Exterior Lighting Battery Saver
If the manual lamp control has been left on, the exterior
lamps will turn off approximately 10 minutes after the
ignition is turned to LOCK and any door has been
opened. This protects against draining the battery in
case you have accidentally left the headlamps or parking
lamps on. If you need to leave the lamps on for more
than 10 minutes, use the manual control to turn the lamps
back on after the ignition has been turned to LOCK and
any door has been opened. To delay the lamps from
turning off, see ªAutomatic Headlampsº in the Index.

2-48 Parade Dimming
To activate the instrument panel backlighting during
the day, turn the headlamp switch to the parking lamp
position. Dimming of the instrument panel display is
not possible during daylight hours. The instrument panel
display can only be adjusted when the parking lamps
are on and it is dark outside.
Perimeter Lighting
When the unlock symbol on the remote lock control
transmitter is pressed, the DRL headlamps, parking
lamps and back
-up lamps will turn on for approximately
25 seconds if it is dark enough outside.
This feature can be programmed on or off for each
transmitter. You can also program how long the
exterior lamps will stay on after unlocking the vehicle.
You must program this feature through the Driver
Information Center (DIC). See ªDIC Personalization
Programmingº in the Index.
Front Reading Lamps
These lamps and the interior courtesy lamps will come
on when you open a door. They will turn off when you
turn on the ignition. If a door is left open, they will turn
off after about 10 minutes.
To turn on the reading lamps when the doors are closed,
press the button under the lamp you want on. Press it
again to turn the lamp off.
These lamps work even when the ignition is off. To avoid
draining your vehicle's battery, be sure to turn off all
front and rear reading lamps when leaving your vehicle.

2-49 Rear Reading Lamps
These lamps will come on when you open the doors.
You can also turn them on by pressing the button on the
side of the lamp. Press it again to turn them off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's
battery against drainage from the interior lamps,
trunk lamp, glove box lamp or cigarette lighters.
When the ignition is turned off, the power to these
features will automatically turn off after 10 minutes.Power will be restored for an additional 10 minutes if
any door is opened, the trunk is opened or the courtesy
lamp switch is turned on. To restore power back to
the cigarette lighters the ignition must be turned back
to RUN.
Battery Load Management
The battery load management feature is designed to
monitor the vehicle's electrical load and determine when
the battery is in a heavy discharge condition. During
times of high electrical loading, the engine may idle at a
higher RPM setting than normal to make sure the battery
charges. High electrical loads may occur when several
of the following are on: headlamps, high beams, fog
lamps, rear window defogger, high blower fan, heated
seats and engine cooling fans.
If your vehicle's battery remains in a heavy discharge
condition for a long period of time, the blower fan,
rear defogger, heated seats and heated mirrors will be
disabled and the DIC will display BATTERY SAVER
ACTIVE. This can happen either under long periods of
idling or low speed driving with high electrical loading,
or in the event of a charging system fault.

2-50
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror may also
contain OnStar

controls.
This is the on/off button for mirrors equipped
with OnStar controls.
Pressing the MIRROR button (or the on/off button for
mirrors equipped with OnStar controls) located at the
bottom of the mirror, turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing.Mirror Operation
To turn on the automatic dimming feature, press MIRROR
(or press and hold the on/off button for about three seconds
for mirrors equipped with OnStar controls). To turn off
automatic dimming, press MIRROR (or press and hold
the on/off button for about three seconds for mirrors
equipped with OnStar controls) again. The green indicator
light will be illuminated when this feature is active.
The automatic dimming feature will be active each time
the vehicle is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors equipped
with OnStar controls) once to turn the compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for approximately
two seconds. After two seconds, the mirror will display the
compass heading.
Compass Calibration
If after two seconds, the display does not show a compass
heading (ªNº for North, for example), there may be a
strong magnetic field interfering with the compass. Such
interference may be caused by a magnetic antenna mount,
magnetic note pad holder or a similar magnetic item.
If the letter ªCº should ever appear in the compass
window, the compass may need calibration.

2-52 Power Remote Control Mirror
The controls on the driver's door operate both outside
rearview mirrors. Move the L/R switch to the left (L)
to select the driver's side rearview mirror, or to the
right (R) to select the passenger's side rearview mirror.
Then press the arrows on the four
-way pad to adjust
each mirror so that you can see a little of the side of
your vehicle when you are sitting in a comfortable
driving position.Leave the L/R switch in the center position to disable
mirror movement by the four
-way control pad.
If your vehicle is equipped with the memory function,
the mirrors and driver's seat position, can be stored into
memory. See ªMemory Seat and Mirrorsº in the Index.
Parallel Park Assist Mirror (If Equipped)
If you have the memory seat and mirrors feature,
the passenger's outside rearview mirror also includes a
tilt
-down feature that operates when the shift lever is
in REVERSE (R). When the vehicle is shifted out of
REVERSE (R), the passenger mirror will return to its
original position after a five
-second delay. This delay
prevents movement of the mirror if multiple gear
transitions (REVERSE (R) to DRIVE (D) to
REVERSE (R)) occur during a parallel parking
maneuver. This feature can be programmed on or off
through the DIC. See ªDriver Information Centerº
or ªPersonalization Featuresº in the Index for
programming instructions. Vehicles are delivered
with this feature off.